Fixes accesses a renamed variable when a specific Kconfig is
active that would cause a compile error.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds a test which enables all Kconfig options for MCUmgr (that are
not deprecated and can be supported on the nrf52840dk board) to
ensure that if a breaking change is introduced in CI then it can
be caught.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Ensure maximum size of common extended header format be
reserved when CONFIG_BT_CTLR_ADV_RESERVE_MAX=n is used so
that changes to ACAD, like channel map update does not need
frequent update to periodic advertising auxiliary channel
PDU time reservations.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When calculating the offsets between primary advertising
PDU, auxiliary PDU, Periodic Advertising PDU, and BIS PDU,
the values used as anchor points for starting the periodic
interval for auxiliary, periodic and BIG events, should be
ensured to have the minimum auxiliary frame spacing T_MAFS
between the PDUs. EVENT_OVERHEAD_START_US has to be reduced
as this value is used to offset the start of the radio
event on air.
Reverts commit b867f0e8a6 ("Bluetooth: Controller: Fix
T_MAFS between broadcasting roles").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Enable advertiser main to support relay messages, this maximizes
theutilization efficiency of advertising sets, which is helpful for the
sending of dense relays, but for Friend and LPN, it delays the sending
of local messages a little, this may cause the time slot deviation between
friend and lpn, and the power consumption of lpn will increase.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
For Mesh Message, should only process by model layer when dst
is unicast address of this nodes or model subscrip on.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
The code in prep_c sets VBAR to relocate vector from 0x0, assuming the
low vector bit in SCTLR to be clear. This isn't the case on all
hardware, so set it explicitly to support those.
Signed-off-by: Théophile Ranquet <theophile.ranquet@gmail.com>
This commit changes the way bonding between endpoints is processed.
There is no blind attempt to read the buffer without mbox notification.
On second side the notification is repeated multiple times until valid
bonding is detected.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
The default number of buffers (contexts) for locally initiated
procedures was 4. Per default the host initiates 3 procedures
when opening a connection, allowing the application to initiate
only 1 additional procedure in parallel.
This commit increases the default to 6, if auto phy-update and
dle is enabled, increasing the robustness for an application.
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
This commit configures the testcase to run on the
stm32u5x5 target boards. USART2 is selected
Pins Tx and Rx (PD5 PD6 on CN9) must be connected on the HW board
to pass the test.
The USART transfer uses the GP DMA transfer with request
27 and 26 on 2 DMA channels (0-15).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit configures the testcase to run on the
stm32u585 target boards. USART3 is selected
Pins Tx and Rx (PD8 PD9 on CN14) must be connected on the HW board
to pass the test.
The USART transfer uses the GP DMA transfer with request
28 and 29 on 2 DMA channels (0-15).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When DMA transfer is enabled on the stm32U5,
the UART Tx channel must be suspended before stopping.
This will let the on-going transfer ends properly
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit is optimizing the uart isr execution to avoid starting
the Rx timeout if it is null. In anycase the async_timer_start
function is checking the tiemout value. This will just save some
execution lines.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Gives the stm32u5 dma driver a suspend function to
enhance the dma API.
This is a particular feature of the stm32U5 GPDMA
to suspend a channel.
A delay is required ;1ms is compatible with both stm32u5 platforms.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Kconfig uses commas to separate macro arguments.
Improve Kconfig documentation by describing to users how this can be
handled when using devicetree Kconfig macros when using devicetree names
which may have commas in them.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
With the current LLDP implementation in Zephyr the support for it has to
be enabled in the ethernet driver. This commit adds exactly this
capability to the STM32 HAL based ethernet driver.
Signed-off-by: Jan Krautmacher <jan@krautmacher.org>
Remove the CONFIG_FPU for the stm32f3_disco and
stm32373c eval boards.
The FPU exists like on many other stm32 series
but CONFIG_FPU has not to be defined here.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The Flash latency depends on the sysclock
In case of the stm32F7 the regulator overdrive mode is set
depending on the sys clock freq.
The overdrive must be set before the first LL_SetFlashLatency.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the support jedec configuration to run
the jedec sample application. So target boards can display
the content of the octo-NOR flash
of the stm32u585 and stm32l562 or stm32h735 disco boards.
The sfdp-bfp table is provided as example (overlay file),
to run this sample on the stm32l562e_dk platform.
It has to be defined in the deviceTree "in cases were runtime
retrieval of SFDP data is not desired."
Signed-off-by: Francois Ramu <francois.ramu@st.com>
No sfdp-table property given by the DTS but received from
the octoflash Node rely on the issued by the read sfdp command.
Note that the size of the mx25lm51245 flash controller
is expressed in bits (ie 512Mbits or 64 Mbytes).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When the SFDP table is provided by the DeviceTree with sfdp-bfp property
It is NOT read from the octoFlash.
If no table exists in the DTS and flash read SPDP fails,
the device init fails.
Availability of this sfdp_read API is conditional
on selecting CONFIG_FLASH_JESD216_API.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds the jedec216 read JEDEC ID function API.
The ospi commands are issued to the octo flash device or
by the DTS jedec-id property.
Availability of this API is conditional
on selecting CONFIG_FLASH_JESD216_API.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fixes command configuration to have samples/drivers/spi_flash
passed on stm32l562 and stm32u585 disco kits.
In OctoSPI STR/DTR and SPI/STR modes,
to determine the address_width, checking the jesd216_bfp_addrbytes
on JESD216_SFDP_BFP_DW1_ADDRBYTES_VAL_3B4B or _VAL_4B.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Changing pcie0 to pcie0: pcie0 allows it to be referenced as &pcie0. I
am not sure why this is required. Otherwise I get error:
...
parse error: undefined node label 'pcie0'
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
nRF52840DK documentation was updated with details on how to change UART1
pins. nRF52833DK and nRF21540 boards has the same incorrect instructions
and were not fixed. Do it now.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
With the stm32U5, when the sysclock is > 55 MHz, the EPOD booster
must be configured before the PLL1 is enabled (see refMan).
This is the case when sysclock is on PLL1 sourced by MSIS or
HSE higher than 16MHz.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Adds the dma transfer for the octoSPI on NOR octo Flash
of the b_u585i_iot02a disco kit.
The channel for the GPDMA is 0-15 (0-7 for DMA1, 8-15 for DMA2)
The channel 12 to 15 are used for GPDMA transfers
to/from external memories.
The request is 41 for the OCTOSPI2.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
For the stm32U5 serie, the busy flag is handled as other serie.
When the DMA is overriden by other HAL drivers, the busy flag
is not considered.
Refer to https://github.com/zephyrproject-rtos/zephyr/pull/47645
There is no Mux for this GPDMA and fixed 16 channels.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit set the stm32 octospi drivers for the stm32u5x
when DMA (GPDMA) is transferring.
Valid for octospi1 or octospi2.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove Kconfig file samples/subsys/usb/usb_pid.Kconfig added in
the commit e5cbe6a9e7 ("usb: cdc: Add unique PIDs for each sample")
with the motivation to have a separate ID for each sample supposedly
to be recognizable by the host.
The new USB support does not use the options, VID/PID is set
directly in the application. As a note, it is not necessary to have
unique PID for each sample, especially for the well known USB classes.
Replace the individual Kconfig options in the documentation
by a table with the references to the samples and PIDs.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
mcc.c does not include `conn_internal.h` so it does not
know the `bt_conn` struct, causing logging issues when
trying to log a `bt_conn` pointer.
Fixed by casting the `conn` pointers to `(void *)`.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add a sample that demonstrates usage of the nPM6001 PMIC (all of its
functionalities).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This aligns the conditional compilation logic with the one used for the
prototype in net_pkt.h, avoids build errors due to a undefined reference
to net_pkt_print_frags.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
