This needs to use 'main' for its default now.
Without this patch, GitHub redirects to main, but displays a banner
that says 'Branch not found, redirected to default branch' at the top.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove dead code enum tracing_log_id
Not used anywhere in the code. Also it caused MISRA rule 8.12
violation.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
This board uses an old bootloader version. The bootloader
always relocate code due to flash bootloader. This imply
a wrong behaviour when using --offset. This is fixed using
bossac legacy mode.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add compatibility mode with old sam-ba flash bootloaders that don't have
offset capabilities. These bootloaders flash to a pre-defined flash
region. At end, bossac will suppress --offset parameter.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Coverity detected that a zero divisor can be passed to
ll_create_connection() without parameter sanitization. Conditionally
check the connection creation parameters according to spec.
Fixes#35343.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Treat warnings as errors. Since we already disable warnings for
undocumented members (the major source of warnings), reported warnings
are in all cases real problems that should be fixed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
1. functions can only belong to one group, use arch-timing (already
defined)
2. group was not properly terminated
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
On sending write request we should check write response.
If data prepaired to be written by peer or offset are not equal
to the data and offset we sent, we shall send Execute Write
Request with Request Flag set to 0x00 (Cancel All Prepared Writes).
This was affecting GATT/CL/GAW/BI-32-C and GATT/CL/GAW/BI-37-C
Signed-off-by: Krzysztof Kopyściński <krzysztof.kopyscinski@codecoup.pl>
Fix the missing HCI event data len limit check when encoding
incomplete advertising data report.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Max data length has to be adjusted for subevent code, otherwise we'll
hit an assert when trying to add data to event due to insufficient
free space.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
After system reset (SETETHRST) interrupt enable register (EIE)
has the default value 0x8010 and global interrupt enable flag (INTIE)
is set. This is not desired and the INTIE flag should be set only at
the end of the initialization.
Disable INTIE flag and set desired interrupts sources in
a single write command just right after system reset.
Resolves: #35091
Reported-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The controller has several interrupt sources which are signaled
via a single INT pin. Only the interrupt sources that are explicitly
switched on during controller initialization may generate an interrupt
signal. Currently there are only PHY Link Status Change Interrupt
and RX Packet Pending Interrupt enabled. So there is no other reason why
an interrupt can be triggered.
Terminate interrupt handling thread on unknown interrupt
only when debugging, as there are concerns that stopping
thread in the field is going too far.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Enable the option to pause the fallback hardware watchdog if the MCU is
halted by a debugger.
This fixes issue #33509 where some boards with Nordic MCUs could not be
flashed anymore after using the task watchdog sample.
Signed-off-by: Martin Jäger <martin@libre.solar>
Enable the option to pause the watchdog if the MCU is halted by a
debugger.
This fixes an issue with some Nordic MCUs (see #33509) where the board
could not be flashed anymore if a short watchdog timeout (<100 ms) was
used.
Signed-off-by: Martin Jäger <martin@libre.solar>
arcmwdt toolchain has various pre build libraries, we can find it in
path: {METAWARE_HOME}/lib, and it will use av2em lib by default.
it's OK for em boards, but not suitable for hs boards. I have tested
hs38_full library for hs boards, it's OK. let's use it.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
The resource description on the OMA LwM2M registry states that only the
first instance of a particular error should trigger creation of a new
error code instance.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Added test which validates that uart device correctly handles
going to and from low power state.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Function should return -ENOTSUP when asynchronous api is not
supported by the device.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Deadlock may occur when uart device was put to low power state
while uart_poll_out was in progress. Poll out pends until uarte
is ready to send new byte and it is detected by endtx and txstopped
events being set. When uarte was disabled while poll_out was pending
events were never set and that lead to deadlock. Added a step
in going to low power state in which CPU waits for txstopped event
and only after that uarte peripheral is disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Every va_start() currently triggers a FPU access trap if FPU is not
already used. This is due to the fact that va_start() must copy FPU
registers that are used for float argument passing into the va_list
object. Flushing the FPU context to its owner and granting access to
the current thread is wasteful if this is only for va_start(),
especially since in most cases there are simply no FP arguments
being passed by the caller.
This is made even worse with exception code (syscalls, IRQ handlers,
etc.) where the exception code has to be resumed with interrupts
disabled upon FPU access as there is no provision for preserving an
interrupted exception mode's FPU context.
Fix those issues by simply simulating the sequence of STR instructions
that the va_start() generates without actually granting FPU access.
We limit ourselves only to exception context to keep changes to a
minimum for now.
This also allows for reverting the ARM64 exception in the nested IRQ
test as it now works properly even if FPU_SHARING is enabled.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
There is no known TFM/secure side solution for the lpcxpresso55s28.
The '_ns' board config variant was added as a copy/pasted based on
how some other boards did things. If/when TFM supports the board
we can revert this to support it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Changes CMakeLists.txt in TensorFlow samples from explicit file
list to a GLOB capturing src/* to make TensorFlow samples consistent
with other samples in tree.
Signed-off-by: Lauren Murphy <lauren.murphy@intel.com>
Fixes documentation for samples that incorrectly state that TensorFlow
library requires the -fno-threadsafe-statics flag to compile.
Signed-off-by: Lauren Murphy <lauren.murphy@intel.com>
Adds no-threadsafe-statics to compiler flags for gcc and arcmwdt.
The flag is required to compile the samples - the module can compile
without it.
Signed-off-by: Lauren Murphy <lauren.murphy@intel.com>
(same considerations as commit 2f01479b)
In a multi-instance driver it may happen that on some h/w
one device should use interrupts and a second device should use
polling mode. So, CONFIG_IIS2ICLX_TRIGGER is not enough to discriminmate
if interrupt inizialization routine should be called or not; the choice
is now based whether the "irq-gpios" property is present in the DT
for that particular instance or not.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use gpio_pin_configure_dt() and gpio_pin_interrupt_configure_dt()
for drdy_gpio: they result in a more readable code.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add test to statically allocate a minimum-size heap, verify that it
works to allocate a single byte and that it doesn't overrun its memory
bounds.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The K_HEAP_DEFINE macro would allow users to specify heaps that are
too small, leading to potential corruption events (though at least
there were __ASSERTs that would catch this at runtime if enabled).
It would be nice to put the logic to compute this value into the heap
code, but that isn't available in kernel.h (and we don't want to pull
it in as this header is already WAY to thick). So instead we just
hand-compute and document the choice. We can address bitrot problems
with a test.
(Tweaks to heap size asserts and correct size bounds from Nicolas Pitre)
Fixes#33009
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The interrupt offload testcases fail on some boards because the timing
of the delay is too short. Refine the testcases and make it not rely
on the delay timing.
Fixes#35097Fixes#35241
Signed-off-by: Enjia Mai <enjiax.mai@intel.com>
This patch enables the DMA chan_blen_transfer and loop_transfer tests on
the nucleo_f070rb board.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
The STM32F0 MCUs (except STM32F030XC) don't have a DMA channel selection
register (DMA_CSELR). This patch fixes the build of the dma_stm32 driver
for them.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
The hardware watchdog was always fed with channel ID 0. This is correct
in most cases, but we should still use the actual ID returned from
wdt_install_timeout.
Signed-off-by: Martin Jäger <martin@libre.solar>
As of today we assume that the help text contained in the Kconfig help
field will be properly formatted RST. However, there is no guarantee
that this will happen. This patch tries to address this problem by:
- Escaping inline RST characters for text that needs to be rendered as
"normal text" (i.e. prompt)
- Use code-blocks to render help content. This way help is rendered as
literal text and so it does not get processed by the RST parser.
A secondary change: the index table now contains the prompt information
only. The page was taking a long time to render because of the large
amount of content. Using a table doesn't help either. Note that adding
code-block to include help as a literal increases build time even more,
so it is not an option.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adds a note on a known config conflict with mbedtls 2.26.0 and TF-M
where the mbedtls PSA APIs can no be enabled at the same time as TF-M.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
the `doc-examples` project is not used and, in fact, is a duplicate of
the Zephyr project.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
