In the eeprom read operation, when rambuf was available
mutex was not unlocked after the read. Consequence of that is
that device was blocked after that read for incoming operations.
This commit fixes the issue
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
This CL replaces offset macros of pmc 'multi-registers' such as
PWDWN_CTLn with internal inline functions for better readability.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL replaces offset macros of scfg 'multi-registers' such as DEVALTn
and LV_GPIO_CTLn with internal inline functions for better readability.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Document that using west outside of a west workspace needs
ZEPHYR_BASE to be set. If this is not set, the instructions
on the "Application Development" page don't work.
Previously, "Getting Started Guide" and "Application Development"
pages told you to run `zephyr-env.sh/zephyr-env.cmd` which would
set ZEPHYR_BASE, but this was removed in Zephyr 2.3.0
Signed-off-by: Daniel Wong <drojfjord@gmail.com>
In the eeprom read operation, when rambuf was available
mutex was not unlocked after the read. Consequence of that is
that device was blocked after that read for incoming operations.
This commit fixes the issue
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add driver implementation and header files for a MEC172x
aggregated interrupt driver. Enable the parent(ECIA) node
to have the driver initialize interrupt hardware for use.
Enable child nodes for those GIRQs used for aggregation.
Refer to chip documention for the list of GIRQs restricted
to aggregation and those which support direct mode.
Add chip level device tree node for MEC172x EC interrupt
aggregator parent and GIRQ children. Each child node contains
a list of sources representing the source bit position in the
GIRQ registers.
Add DT bindings for ECIA and GIRQ nodes.
Add build file(s) and configuration items for the MEC172x ECIA
aggregated interrupt driver. Add and enable the MEC172x interrupt
driver on the MEC172x evaluation board(EVB). Enable parent node to
initialize ECIA hardware. Child nodes are left disabled until a
future driver needs them.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Check for the address family of the packet when setting the multicast
destination address used in the response. Current code checks either the
query type or the stack configuration, which can result in setting the
wrong type of address for the frame.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
In order to avoid to generate warning log message from
file system, first check if directory exists before trying to
create it.
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
There are multiple reasons to want to find out if file or
directory exists, for example to create it. Stating and
finding out it doesn't exist should not cause an LOG_ERR call as
this gives information to the user in a normal call case.
Fixes#35718
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
To be consistent in how order header flags are handled when
updating the common header format fields, explicit check
for ADI flag in previous auxiliary PDU buffer.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remember last used DID for each SID, so that DID value used,
when updating the advertising PDU fields, change between
consecutive changes to PDU fields.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Make the Extended Advertising DID value updated to be unique
for every new advertising set created.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Verify that AD Data when switching to Legacy Directed, and
restore it when switching back to Legacy Non-Directed
Advertising mode.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix corrupt AD data used after directed advertising by
storing a backup of the AD data before switching to directed
advertising. Restore back the AD data with switching to non-
directed advertising.
The fix also addresses AD data backup when switching between
Legacy and Extended Advertising.
Fixes#18850.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation to resolve AdvA in the received
AUX_CONNECT_RSP PDU before generating the connection
complete.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit adds support for SDMMC driver, Which
was missing. THi commit will solveserror SDMMC init
error on stm32l496g_disco boards.
Signed-off-by: Affrin Pinhero <affrin.pinhero@hcl.com>
This commit adds support for SDMMC driver,
Which was missing. THi commit will solves
error SDMMC init error on STm32F746G_DISCO
boards.
Signed-off-by: Affrin Pinhero <affrin.pinhero@hcl.com>
Add support for sam_e70_xplained, sam_v71_xult based on TC0 counter.
Note: TC module is a 16-bit counter. Even with slow, 32768 Hz input
clock the time span counted by the driver is short.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add basic counter driver based on Timer Counter (TC) module for Atmel
SAM family.
Remarks:
- The driver is not thread safe.
- The driver does not implement guard periods.
- The driver does not guarantee that short relative alarm will trigger
the interrupt immediately and not after the full cycle / counter
overflow.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Change naming of TC_CHANNEL to TcChannel in Tc struct to align with
a new convention used by samv71, samv71b series.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update to include the commits:
- patch: same70, samv71: Add TC waveform/capture mode registers
- patch: same70, same70b: Align naming of TcChannel in TC
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
According to the Reference Manual of several series(G0,L5,WL,WB,...)
RNG_DR register value should only be used if it is different from 0:
"Because when it is the case a seed error occurred between RNG_SR
polling and RND_DR output reading (rare event)."
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit introduces an automatic recovery procedure in cases an
entropy source error was detected.
- On Series with soft reset support a soft rest is executed.
- On Series w/o soft reset support the pipeline is cleared by reading
the RNG_DR 12 times.
With this changes the check for seed errors uses SEIS flag instead
of the SECS flag.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Define SoC hooks as weak symbols so this way applications can
overwritten them defining strong symbols.
The problem is that currently SoCs are defining these interfaces as
strong symbol inhibiting the possibility of applications bring their
own implementation.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
SoC hooks are defined as weak functions for the case where they are
not implemented by a SoC. The problem that may happen is when an
application define it as weak as well. In this case, no compilation
error is issued but the version that will be used depends on the build
order. Just remove the weak placeholder implementation.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This board has the capability to use SERCOM2 as an i2c
interface on pins 8 and 9.
This adds the neccessary pinmux settings and devicetree
node.
Tested with the i2c shell module.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
Interrupt polarity register don't support rising and
falling edge triggered at the same time, so I correct
logic operation to match this.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
Correct SYS_CLOCK_HW_CYCLES_PER_SEC and
SYS_CLOCK_TICKS_PER_SEC to match our real setting value
for precise timing.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
When the Hardware Information Driver (HWINFO) provides a device ID
longer than the configured USB serial number, truncate the most
significant part instead of the least significant part. The lower part
is usually having more entropy, e.g. on STM32.
Fixes#34550
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add the missing includes to make the header more portable. It currently
requires other headers to be included before it.
Signed-off-by: Yuval Peress <peress@chromium.org>
SMP implementation across bt/udp does not check
if allocation of the buffer was successful.
If the buffer is not granted an error shall be
returned.
This patch fixes BUS FAULT issue when NULL
pointer is referenced.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit updates the supported features of stm32l5 and stm32wl boards
to match the devicetree configuration.
- add link to board defconfig and board.dts
- sort supported features table alphabethically by interface.
Additionally CRYP peripheral is added as supported feature to the
mikroe_mini_m4_for_stm32 board documentation.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The test sample.drivers.crypto.stm32 was built only for the stm32 crypto
driver (build_only: true).
This commit changes the configuration to run the test and adds regex for
the supported modes.
Additionally integration_platform native_posix is removed from the
crypto.stm32 test configuration, such that stm32 targets built in CI.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit uses filter instead of allow list for the
sample.drivers.crypto.stm32 test case.
As a result the ci test is not only built on mikroe_mini_m4_for_stm32,
but also on lora_e5_dev_board, nucleo_wl55jc and stm32l562e_dk.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds dt definitions for the hw aes accelerator
on stm32g0 Series.
The accelertor is available on the following socs:
stm32g041, stm32g061, stm32g081, and stm32g0c1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds a dt node for the hw aes accelerator of the
stm32l5 series.
The stm32l562Xe.dtsi file now includes the newly created
stm32l562Xe.dtsi with the additional aes definitions instead of the
stm32l552Xe.dtsi file.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
