Add infrastructure to allow user to configure the system so that
all the network packets, that are sent to or received from a specific
network interface, are sent to remote system for analysis.
The captured network packets are placed as a payload in UDP packet,
which is then sent inside a tunnel to a remote host. The host can
then receive the packets and for example show them in wireshark.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add get/set helpers to store information whether the net_pkt
is captured already or not. This bit is used to detect capture
loop and avoid recursion.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of forcing net_pkt_clone() use the tx_pkts slab, use
the same slab that was used when allocating the original net_pkt.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPIP tunnel capability bit helps to detect which network
interface supports IPIP tunneling.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Shared data can't live on thread stacks if they are incoherent. These
are all just per-test-case data, so make them static.
Fixes#33898
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Usually, GCC builtin or arch-specific atomic functions are being
used. The corresponding kconfigs are "selected" by architecture
or SoC kconfigs. CONFIG_ATOMIC_OPERATIONS_C is usually used to
override the GCC built-in or arch-specific atomic functions when
these two are not supported. So change the priority of #include
so that C version is included first if selected, and skips
the inline versions of the other two variants. Or else there
will be two compiled versions of atomic functions: inline version
and the compiled C version. Note that the arch-specific version
and builtin are swapped, so the builtin one is now the default.
Fixes#33857
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The builtin atomic header file should not include the syscall
header that is generated from C version of atomic functions.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Xtensa cores are highly configurable so each SoC may not have
the needed instructions for the hardware assisted atomic
operations. So instead of selecting the arch-specific atomic
operations kconfig, do a "imply" instead. So SoC or board
configs can disable this.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Implement SO_BINDTODEVICE socket option which allows to bind an open
socket to a particular network interface. Once bound, the socket will
only send and receive packets through that interface.
For the TX path, simply avoid overwriting the interface pointer by
net_context_bind() in case it's already bound to an interface with an
option. For the RX path, drop the packet in case the connection handler
detects that the net_context associated with that connection is bound to
a different interface that the packet origin interface.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Turns out that we could flatten the tree further as there is not
that many files to warrant a whole directory for this.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The STMEMSC HAL i/f requires every driver using it to define
for each instance a stmdev_ctx_t structure, which is used to
export the hardware specific APIs to handle i2c and spi busses
operations. Since this structure is bus agnostic, there is no
need to declare it twice for both i2c and spi. Instead, declare
only one structure, which will be populated either with i2c APIs
or with spi APIs according to where that particular instance is
declared inside the DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Make use of the stmemsc i2c/spi read/write routine that
has been introduced to simplify the ST sensor drivers code.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add common i2c/spi read/write routines for the benefit of those
ST sensor drivers who make use of the stmemsc HAL i/f.
Add generic stmemsc_cfg_i2c and stmemsc_cfg_spi structures which
contains all relevant information required by i2c/spi low level
routines, such as:
- the pointer to the bus device
- the I2C slave address (if instance is on I2C bus)
- the spi_config structure (if istance is on SPI bus)
This level of abstraction allows the re-use of the i2c/spi read/write
routines among all stmemsc based sensor driver without the need to
reference the specific sensor data and or config structures.
The STMEMSC HAL source code is located here:
zephyrproject-rtos/modules/hal/st/sensor/stmemsc/
Signed-off-by: Armando Visconti <armando.visconti@st.com>
soc/arm/st_stm32/CMakeLists.txt already has a
zephyr_include_directories(common) so including in again
soc/arm/st_stm32/common/CMakeLists.txt is redudant.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
An option has been added which can be passed to setsockopt
which allows the user to set & get the dtls handshake timeout,
either before first handshake or online.
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
CMSIS_DSP and net_socket tests are either too
slow or too large for this platform, also drop
bluetooth for test
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Remove dead code from twisterlib.py which is a copy of code
from twister script. This redundancy causes pylint errors in
compliance checks.
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
Enable half transfer interrupt of the dma controller
in case the channel was enabled in circular mode.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
The usage of EXTRA_DTC_FLAGS was removed in commit
269f350487
If ninja was used and e.g. menuconfig is called, when more than one
element is in EXTRA_DTC_FLAGS, calling "ninja menuconfig" failed.
E.g.
west build -b lpcxpresso55s28_ns -t menuconfig samples/hello_world
resulted in and error. This is fixed with this commit.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
After 3a58b45ced introduced the option
of specifying valid board revisions, it is no longer needed to provide
a .conf file for each revision. Remove then the files that were added
solely for this reason and use the VALID_REVISIONS parameter instead.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
On stm32, the M bits defines the length of the frame between the start
bit and the stop bit, eventually including the parity bit when enabled.
Fix configuration of databits to set correct M bits when parity is
enabled.
This commit tries to address issue zephyrproject-rtos/zephyr#33351
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
STM32L011 and STM32L031 do not support USART1.
This commit moves the definition of the node to only
be present for MCUs which support the peripheral.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
TIM7 peripheral was defined for all STM32L4 chips
in the device tree when not every chip supports it.
This commit moves the node so that only chips
which support the peripheral have the node defined.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
The device tree includes CAN node can1 for all
STM32L4 chips when in fact they don't all support it.
This affects STM32L412xx and STM32L422xx.
Fixes#33896
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
Update revision of hal_nordic which introduces new radio driver
integration scheme.
The glue cmake has been updated to use the new integration scheme
for the nrf-802154 component.
Added config option to exclude radio driver in hal_nordic from the
build process. This allows the radio driver to be supplied from
other sources.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The default value is not needed because there is only one choice.
This allows the default choice to be set in a different module.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Fix packet reordering in ATT when putting the host under high load.
In certain conditions a packet can be transmitted while there is
elements in the TX queue in bt_att_send. This means that the packet will
skip ahead in the TX queue leading to packet re-ordering.
Fix by always appending to the queue, and then initiate sending of the
HEAD of the queue.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Some tools consider this as commented code because of the ifdef, so
remove that and fix a coding guideline violation.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Tests of a value against zero should be made explicit, unless the
operand is effectively Boolean. This is based on MISRA rule 14.4.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Tests of a value against zero should be made explicit, unless the
operand is effectively Boolean. This is based on MISRA rule 14.4.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This functions is being called across the tree, no reason why it should
not be a public API.
The current usage violates a few MISRA rules.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add a 'U' suffix to values when computing and comparing against
unsigned variables and other related fixes of the same MISRA rule (10.4)
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The size of ctx->rx_adu.data is not CONFIG_MODBUS_BUFFER_SIZE. Coverity
flagged the potential overwrite so just use sizeof().
Fixes#33789Fixes#33792Fixes#33818
Signed-off-by: David Leach <david.leach@nxp.com>
With these changes, dial up Zephyr application/driver can use
socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW) for creating
a socket for sending/receiving data to/from ppp net link, i.e.
packet is going to/from PPP L2.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
Introducing PPP dialup features to enable e.g. usage of nrf9160
based board as a dialup modem for transferring ip data over PPP
(e.g. windows dial up), i.e. usage of Zephyr PPP as a server for
providing MTU/MRU, IP address and DNS addresses for a PC:
- PPP LCP MRU option (configurable)
- PPP server: IPCP ip and dns address peer options to enable
providing IP and DNS addresses for PPP peer.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
The specification states that the server can cancel observations "at any
moment, by sendinga GET request with Observe option=1, the LwM2M Server
cancancel an “Observe”operation on a specified Resource, or specified
Object Instance(s)."
It does not mention any token matching requirement, but RFC 7641 does.
The correct interpretation is not obvious. The EMQx LwM2M implementation
uses a new token for instance, which does not work with Zephyrs token
matching cancel-observe.
This commit introduces cancel-observe via path matching as a Kconfig
option. This could hypothetically introduce problems when we are
connected to multiple peers simultaneously, but since that is not likely
to be supported for a long time (if ever), this change should be fairly
uncontroversial since path matching is only used as a fallback.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
The comparison was inverted before so configuring a valid window
providing min and max was not possible.
Now the comparison is corrected and only done if the watchdog is used in
windowed mode.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Use a combination of fixed-clock and fixed-factor-clock devicetree
nodes for describing the clock dividers/multipliers of the NXP Kinetis
System Clock Generator (SCG) present in the KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
