Refactor HTML targets. The 'html' target is kept as is, 'sphinx-html'
equivalent is now 'html-nodeps'.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Group dependencies all together. Some have been simplified, e.g. Sphinx
and others improved, e.g. LaTeX.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
west is currently optional, however, when not found its docs will not be
available and the zephyr_module CMake utility will not be able to find
modules (unless ZEPHYR_MODULES is used). Other Python dependencies, i.e.
the ones listed in the requirements file, are not checked, so do the
same for west.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
We excluded the beaglev_starlight_jh7100 from this test but only did
the kernel.device.pm test. We should have excluded the platform
from both tests.
The beaglev_starlight_jh7100 uses a full 64-bit devicetree map
which uses #{address/size}-cells = 2. The device test expects
that #{address/size}-cells = 1 so exclude beaglev_starlight_jh7100
from the test.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The test ocassionally fails on the mps2_an385 platform in the CI, due
to strict timing requirements of the test.
Relax the timeouts and acceptable fuzz time a bit, to prevent the
failures in the future.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Use GPIO output high and low to simulate I2C start and stop
conditions to restore i2c to normal.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Create the pinmux phandle to the I2C driver node in the
devicetree. When the pinmux_pin_set function in
i2c_it8xxx2_init can refer to the setting of this phandle.
It is more flexible to use.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The SoC driver name is 'USB High-Speed Interface (USBHS)'. This rename
from usb_dc_sam to usb_dc_sam_usbhs allowing add others SoC drivers
like 'USB Device Port (UDP)' that is found at SAM4S/E variations.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Give the choice a name so that the soc/board developers can change the
default selection in their Kconfig.*.
For example:
choice CACHE_TYPE
default HAS_EXTERNAL_CACHE
endchoice
There was a similar issue had beed discussed:
https://github.com/zephyrproject-rtos/zephyr/issues/6948
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Change-Id: I07c3e78a5243b30912f8e44fa3181fa163016318
The `pdftex` utility that is used for PDF documentation generation does
not support GIF images.
This fix replaces the animated `ReelBoard-Blinky.gif` with an animated
PNG (APNG) image `ReelBoard-Blinky.png`.
Note that APNGs are backwards compatible with "normal" PNGs. Modern
web browsers will display APNGs in the same way as animated GIFs, while
any application that can read PNG files can read APNG files
successfully.
Signed-off-by: Chris Pearson <ctpearson@gmail.com>
Adds a BabbleSim test for provisioning multiple devices in a row. This
scenario had a regression in #33782, which is fixed in #35405.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
QUIET flag is now overriden according to the `doxyrunner_silent`
configuration value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This change will process Doxygen output and will map it to the Sphinx
logger. Things like errors and warnings will be mapped to actual Sphinx
logger error and warnings. In practice this means that when Doxygen
throws a warning and Sphinx is run in "-W" (warning as error) mode, the
build will fail. It also has some other advantages such as the
possibility of filtering issues using the warnings_filter extension.
It is also expected that CI errors not being displayed issue is fixed
with this change.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Align the capitalization of the term "Bluetooth Mesh" to Bluetooth mesh"
in the documentation. This is done to to match the new updated naming
convention done in Bluetooth SIG. In the upcoming spec versions, it its
used "Bluetooth mesh" with the lower case convention.
Signed-off-by: Ingar Kulbrandstad <ingar.kulbrandstad@nordicsemi.no>
add min_ram to some test applications
as we found below platforms have size issues
TWR_KE18F and FRDM_KL25Z
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Some commands shell not be present when shell is not acting as
a log backend. Use of them lead to crash in that case.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit changes the entry referencing the hal_stm32 module
into west.yml. This brings the fixes to build issues when stm32
asserts are enabled.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys em_starterkit and HSDK boards.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
This commit add the support of "Interrupt driven UART"
to the R-Car UART driver and enable it in the related
Kconfig.
The driver is supporting nearly all the methods that are
described in the "Interrupt driven UART" part of the
uart_driver_api.
This new version of the driver has been tested on
H3ULCB board by running "uart_basic_api" test suite.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
This commit enables entropy support for nucleo_wl55jc.
Additionally it sets the PLL Q divider to 2, which was not set in
the board dts before.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds the dt node for rng to the stm32wl series
and sets it as chosen zephyr,entropy source.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds support for stm32g0 socs with integrated rng and hw aes
acceleratior, which are stm32g041, stm32g061, stm32g081, and stm32g0c1.
It also adds the definitions for the rng peripheral
and sets it as chosen zephyr,entropy source.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds entropy support for stm32wl and stm32g0.
Pll is used as clock source and has to be enabled,
other clock sources are not supported at the moment.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds support for the seeed studio LoRa-E5 Dev board,
which is powered by a module based on stm32wle5jc soc.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds the dts definitons for the seeed lora-e5 module.
Additionally I add myself as codeowner for the new dts/arm/seeed
directory.
This module packages a stm32wle5jc Sub-GHz Wireless Soc,
together with a 32MHz TCXO, a 32.768KHz crystal oscillator, and
power and RF circuitry.
With the introduction of lora support definitions for the radio
will be added in a future commit.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
To support single core stm32wlex series, cpu2 prescaler is set
only on dual core soc variants.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds support for stm32wle4xx, stm32wle5xx single core socs,
as well as stm32wl54 dual core soc.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds dt support for stm32wle4, and stm32wle5 single core,
as well as stm32wl54 dual core socs.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The callback is not used anymore, so just delete it from the pm_control
callback signature.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
the device PM callback is not used anymore by the device PM subsystem,
so remove it from all drivers/tests using it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback used by the device runtime PM can be easily replaced by a
simple state set after calling the state set/get calls. Broadcast logic
is simplified too, leading to the same previous behavior.
Since this is the only place where this callback was used, it can now be
removed from all devices and so pm_control callback signature
simplified.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The bootloader itself contains the i.MX RT6xx boot header, so we don't
need to duplicate it when building chainloaded applications.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds flash partitions and chosen nodes to the mimxrt685_evk device tree
to support mcuboot on the external octal SPI flash. This flash is rated
for 100K minimum program-erase cycles per sector, therefore this
partition configuration supports approximately 100K / (24576/8128) =
33073 upgrades.
Tested with samples/subsys/mgmt/mcumgr/smp_svr. The image swap takes
about a minute and a half to complete.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
