NXP ls1046a is SoC includes the following functions and features:
1. Four 32/64-bit Arm v8 A72 CPUs
2. Cache coherent interconnect (CCI-400)
3. One 32/64-bit DDR4 SDRAM memory controller with ECC
4. Peripheral interfaces include DPAA network, PCIe, USB, SPI,
GPIO, UART, SDHC, IFC, LPUART ...
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
The stm32 wwdg driver was currently tested only on disco_l475_iot1.
Additionally add nucleo_f091rc, such that one board with an CM0 core is
tested. And add nucleo_g431rb, that one board is included that has
newer register mapping and a 128 prescaler.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
As older series supported only 4 different prescaler values the
highest prescaler value was hardcoded. Newer series support 8
programmable prescaler values, therefore take the allowed values from
ll_wwdg header file.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Series STM32G0, STM32G4, STM32H7, STM32L5, STM32WB, STM32WL have
a newer wwdg ip and store the prescaler value not in bits[8:7],
but bits bits[13:11], use the definitions from ll to account for that.
Remove IS_WWDG_PRESCALER, this is not required as the prescaler
is not calculated, but known valid prescaler values are tested until a
valid counter is found.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Cortex M0 Series only have two interrupt priority bits,
nevertheless all series set the priority per default to the invalid
value of 7.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add tests that validate the behaviour of providing NULL as a data
pointer to discard whatever data is in the ring buffer.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Allow NULL data buffers to be provided to `ring_buf_get` and
`ring_buf_item_get`, in which case data will be discarded instead of
copied out to the user.
Fixes#33488.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add Alexandre and François as collaborators on STM32 Platforms.
Additionally, add one naming for stm32 boards.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update the binding for how we represent pin data to support child
nodes with a nxp,kinetis-pins property that has the pin data.
For example:
UART0_CTS_PTA0: uart0_cts_pta0 {
nxp,kinetis-port-pins = < 0 2 >;
};
Also pull in pincfg-node.yaml to get various common pin flags like
"bias-pull-up", "drive-open-drain", etc.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for run time idle power mode.
Wakeup time from sleep mode varies from 1-7us
depending on the core speed.
Hence picked a min-residency-us value of 10us.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
__ASSERT() macro is used in sys/sflist.h while sys/__assert.h was not
included. Fix that now.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The Kconfig symbol CONFIG_DMA_0_NAME was recently removed. Update the
dma channel link transfer test to get the device name from an
application level Kconfig instead, similar to other dma driver tests.
This fixes a CI compliance failure that checks for references to
undefined Kconfig symbols.
Tested on the mimxrt1050_evk board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
test minor/major link mode on frdm_k64f and mimxrt1060_evk
log as below:
Running test suite dma_m2m_link_test
===================================================================
START - test_dma_m2m_chan0_1_major_link
Preparing DMA Controller: Chan_ID=1, BURST_LEN=1
Starting the transfer
DMA transfer done ch 0
It is harder to be kind than to be wise........
It is harder to
PASS - test_dma_m2m_chan0_1_major_link
===================================================================
START - test_dma_m2m_chan0_1_minor_link
Preparing DMA Controller: Chan_ID=1, BURST_LEN=1
Starting the transfer
DMA transfer done ch 0
It is harder to be kind than to be wise........
It is harder to be kind than to
PASS - test_dma_m2m_chan0_1_minor_link
===================================================================
START - test_dma_m2m_chan0_1_minor_major_link
Preparing DMA Controller: Chan_ID=1, BURST_LEN=1
Starting the transfer
DMA transfer done ch 0
DMA transfer done ch 1
It is harder to be kind than to be wise........
It is harder to be kind than to be wise........
PASS - test_dma_m2m_chan0_1_minor_major_link
===================================================================
Test suite dma_m2m_link_test succeeded
===================================================================
PROJECT EXECUTION SUCCESSFUL
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
1. remove redundant protection on channel status
2. update link interface to support major and minor link
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
The ImgtoolSigner.sign() is passed a BuildConfiguration object instance
that holds all of Kconfig options that have been defined for a build;
yet it has been reading the .config file once again, with the
load_dot_config, to check some of these options.
The commit replaces the code that has been using the load_dot_config
obtained data with the code that uses the BuildConfiguration object.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The body of load_dot_config method has been reimplemented in
BuildConfiguration.get(), replacing the previous code.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The BuildConfiguration.path attribute has been added that stores path
to .config file which has been used as source for options collected to
BuildCOnfiguration object.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Limit adafruit_2_8_tft_touch_v2 sample variant execution to the boards
that have this shield available.
In order to run the test in CI bench, add the following in
twister map.yml file on matching board:
fixtures:
- fixture_shield_adafruit_2_8_tft_touch_v2
For instance:
- connected: true
fixtures:
- fixture_shield_adafruit_2_8_tft_touch_v2
id: 0673FF323535474B43171415
platform: nucleo_f429zi
product: STM32 STLink
runner: openocd
serial: /dev/ttyACM0
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change to use the BT_ATT_FIRST_ATTTRIBUTE_HANDLE and
BT_ATT_LAST_ATTTRIBUTE_HANDLE instead of the literal values where
applicable.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Adds #defines for the minimum (first) and maximum (last)
attribute handles in ATT. These are useful for when setting e.g.
the start and end handle when doing a full GATT discover.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The bt_iso_chan_disconnected assumes a CIS, but was
also used for BIS, so whenever it was called it attempted
to get a non-existing ACL connection.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Fixed the name of nodes in device-tree files by following rules:
If object is 'phandles', use underscores for object name.
If not, such as 'node' or 'property', use hyphens for object name.
This CL also applies normal style for all nodes in npcx device-tree
files.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Upgrade core Python dependencies (setuptools, wheel, pip) at a system
level. Some old versions of pip do not resolve the dependency chain
correctly, this is why it has been added to the list.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
docutils is a core dependency of Sphinx. It is only used by some of our
custom Sphinx extensions.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add the nanopb library and generator tools as a module.
Nanopb is a small code-size Protocol Buffers implementation in ansi C.
It is especially suitable for use in microcontrollers,
but fits any memory restricted system.
Nanopb home: https://jpa.kapsi.fi/nanopb/
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This scripts receives the same parameter of what_changed.py. And run
coccinelle scripts for code guideline compliance in the given git
commits. e.g: ./guideline_check.py --commits origin/master..HEAD
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This coccinelle script can check some violations for rule 21.2.
Currently it is checking the follow reserved names:
"remove", "rewind", "malloc", "free", "exp", "signal"
It can easily be extended in the future though.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Rebnase
This coccinelle script can check some violations for rule 5.7.
It can identify things like:
struct device *device
But it is not capable to identify:
struct test { ... }
...
int test;
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The implementation of blocking calls is common for all the client
models.
This change reduces the code duplication by introducing new API that
helps to manage acknowledged messages.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Switch the default LPC board configuration to select the
TFM_PROFILE_TYPE_MEDIUM choice, instead of directly setting
the TFM_PROFILE variable, as this is now made hidden.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We add a Kconfig choice for the TF-M profile, in
TF-M's Kconfig file. The reason for that is to be
able to easily enable additional configurations,
depending on the profile type being selected. We
also enhance the documentation of TFM_PROFILE,
stressing that there is now also profile_large
available as an option. TFM_PROFILE is now made
hidden, forcing the users to select one of the
available choice symbols. IF the TFM_PROFILE is
set to something other than "none", then certain
options shall be made hidden, namely, IPC and
isolation level, as they are determined by the
profile setting.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add a dependency on IPC for the Audit Log secure service,
since the service is not compliant with the IPC model.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
