This will help not to collide within drivers implementations and/or
avoid dependency from one driver to another one.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Wifi mgmt interface will be required by offloaded wifi device drivers
therefore when selecting this interface, make sure dependencies are
selected too.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add empty WiFi network management functions that only return -ENETDOWN.
Define management handlers for scan, connect and disconnect requests,
again without any implementation nor parameters defined.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
First because nobody needs to know that besides net_mgmt core and
secondary to avoid possible circular dependancy on
net_mgmt.h/net_event.h.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Previously, with CONFIG_OFFLOAD enabled, net_if_up() and
net_if_down() were calling l2->enable, which didn't exist,
so was crashing.
Instead, if CONFIG_OFFLOAD is enabled, it will test for if the net_if is
of an offload type and react accordingly.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Drivers will be directly contacted via net_if's offload attribute. No
need for a an extra layer as an L2.
Signed-off-by: Dario Pennisi <dario@iptronix.com>
Signed-off-by: Massimiliano Agneni <massimiliano.agneni@iptronix.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clean up the text, add an important warning, and add a self-contained
example rather than referring to the internal test code.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
According to RFC 793 we should wait for FIN in FIN_WAIT_1 and
FIN_WAIT_2 states. Receiving ACK in FIN_WAIT_1 just moves us to
FIN_WAIT_2 state.
Right now TCP connection is never closed if FIN is not received
in FIN_WAIT_2 state. Fix that by keeping fin_timer active in
FIN_WAIT_2 state, but canceling it just after FIN is received.
Fixes: 124c067027 ("net: tcp: Cancel the fin_timer on FIN message
in FIN_WAIT1 state")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Without that, if ipv4 is configured via DHCPv4, server will not be
accessible. It looks like it won't properly bind addresses.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The TRNG IP block in the KW41Z is really an entropy source and not
intended to be used as a general purpose random number generator
source. The block has 15 slots to read from and when the last slot
is read it has to regenerate the 15 numbers. This process takes
3-5 seconds and is blocking. The change here is to use the TRNG as
an entropy source to the XOROSHIRO pseudo random number function
and then have the KW41Z use XOROSHIRO for random number generation.
Signed-off-by: David Leach <david.leach@nxp.com>
- Added example OpenThread projects for KW41Z in echo/server samples
- Added projects to sample.yaml for sanity testing
Signed-off-by: David Leach <david.leach@nxp.com>
- Removed OT_PLAT_RADIO_DEVICE_NAME
- Changed OpenThread binding to use NET_AP_IEEE802154_DEV_NAME
- Modified Kconfig chain to ensure NET_AP_IEEE802154_DEV_NAME
is enabled for both native 802.15.4 and OpenThread configurations
- Changed default setting of NET_L2_IEEE802154 in defconfig for mkw41z4.
- Fixed OpenThread api support code to use the state of mIsCcaEnabled
in the transmit frame to conditionally invoke radio_api->cc() on
transmits.
Signed-off-by: David Leach <david.leach@nxp.com>
- Debug code did not compile when level set to DEBUG.
- OpenThread has a define for BASE which conflicts with the BASE
field in MTB_Type defined in MKW41Z4.h. The change is consistent
with how it was handled in the KW41 port in OpenThread.
Signed-off-by: David Leach <david.leach@nxp.com>
- There is a mismatch when interfacing with external code where a
uint32_t is defined as a parameter and internal Zephyr code attempts
to use u32_t. If NewLib is used, the typedef for u32_t is
'unsigned int' which is not a portable match to uint32_t as
'unsigned int' is not a common size across architectures so gcc will
output a warning.
- The mcux flash code calls NXP supplied functions that expect a
uint32_t.
- openthread.c ot_state_changed_handler has a uint32_t flag as a
parameter.
Signed-off-by: David Leach <david.leach@nxp.com>
Make sure we are able to collect ethernet statistics and query
it via net management API.
Fixes#6899
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We returned too early when creating listeners which meant that
IPv4 listener was not created if IPv6 one was created successfully.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- tx_tsv is never used anywhere
- and rx_rsv can be allocated on stack
Optimizing a bit the stack usage in eth_enc28j60_rx() function as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
SPI API helps to directly transfer bytes from/to relevant buffers, so
let's take advantage of it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Driver is still a bit messy, not using for instance the 0-copy
capabilities of SPI API, but this will be fix later.
Constify most of the spi buf structures, removing useless variables,
renaming function with common prefix eth_enc28j60_ etc...
It seems to fix an issue on verifying if tx was successful as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When we added support for the HiFive1 board we forget to make sure it
had a board yaml file. Add the file so we get sanitycheck running on
the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Assign special Product ID (0x101) to wpanusb protocol exporting
IEEE802.15.4 over USB.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Missing newline on end of the file - this cause failure
while try to use menuconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
configuration supports the following hardware features on the Cortex M4
Core:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
boards/arm/colibri_imx7d_m4/colibri_imx7d_m4_defconfig
Other hardware features are not currently supported by the port.
Connections and IOs:
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
was tested with the following pinmux controller configuration.
+---------------+-----------------+---------------------------+
| Board Name | SoC Name | Usage |
+===============+=================+===========================+
| UART_B RXD | UART2_TXD | UART Console |
+---------------+-----------------+---------------------------+
| UART_B TXD | UART2_RXD | UART Console |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
The i.MX7 SoC is a Hybrid multi-core processor composed by Single/Dual
Cortex A7 core and Single Cortex M4 core.
Zephyr was ported to run on the M4 core. In a later release, it will
also communicate with the A7 core (running Linux) via RPmsg.
The low level drivers come from NXP FreeRTOS BSP and are located at
ext/hal/nxp/imx. More details can be found at ext/hal/nxp/imx/README
The A7 core is responsible to load the M4 binary application into the
RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer,
and get the M4 out of reset.
The A7 can perform these steps at bootloader level after the Linux
system has booted.
The M4 can use up to 5 different RAMs. These are the memory mapping for
A7 and M4:
+---------------+-----------------+---------------------------+
| Memory Name | Start Address | Size |
+===============+=================+===========================+
| TCML | 0x007F8000 | 32KB |
+---------------+-----------------+---------------------------+
| TCMU | 0x20000000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM_S | 0x20180000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM | 0x00900000 | 128KB |
+---------------+-----------------+---------------------------+
| DDR | 0x10000000 | 256MB |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Adds a shim layer around the imx uart driver to adapt it to the Zephyr
serial interface.
Modem mode was introduce to control it as DCE and DTE and can be
configured in the device tree:
modem-mode:
type: int
category: required
description: Set the UART Port to modem mode 0 (dce) 1 (dte)
generation: define
For now only the UART 2 was tested.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
This code component is used to add Zephyr support on iMX7 processors,
exclusively on Cortex M4 core, and to speed up the development process
it was decided to have it based on NXP FreeRTOS BSP implementation.
The source code was imported from the following folders:
FreeRTOS_BSP_1.0.1_iMX7D/platform/drivers
FreeRTOS_BSP_1.0.1_iMX7D/platform/devices
This source code depends on headers and sources from zephyr:
ext/hal/cmsis
Origin: iMX7D NXP FreeRTOS BSP Peripheral Driver
License: BSD 3-Clause
URL: https://www.nxp.com/webapp/Download?colCode=FreeRTOS_iMX7D_1.0.1_LINUX&appType=license
commit: no commit hash
Purpose: The peripheral driver wraps the H/W for i.MX7 M4 core
Maintained-by: External
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
commit ec7ecf7900 moved some code around
such that the total_size variable is used regardless of how
CONFIG_MPU_REQUIRES_POWER_OF_TWO_ALIGNMENT is set. So move the
decleration of total_size outside of the ifndef block so things build
properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we have some error parsing a testcase or other files we treat these
as errors and will exit before continuing on building other tests.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Doc incorrectly said to use the word "retest" in a comment when the
correct word is "recheck".
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
