Expands the caching documentation to include a high-level overview
of caching strategies and the features available in Zephyr.
Signed-off-by: Dane Wagner <dane.wagner@gmail.com>
Add device definitions in dt to test drivers that handle
multiple "compatible"s by a single driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Compilation will fail if multiple models are used at the same time.
Changing to define different unique names for the symbols
to avoid conflicts.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The lsm6dso driver does not correctly reflect the status of
the node in dt. So the driver didn't compile even if
`st,lsm6dso32` node exists.
I fixed it to correctly go through ithe compile.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Merge the functions z_thread_stack_alloc_dyn() and
stack_alloc_dyn(), simplifying the flow for dynamic thread stack
allocation.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Modify the extended and periodic interval to be values that
are more suited for audio as they are multiple
of the expected resulting ISO interval.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This removes the deprecated CONFIG_NET_PKT_BUF_DATA_POOL_SIZE.
User should either use CONFIG_NET_PKT_BUF_RX_DATA_POOL_SIZE or
CONFIG_NET_PKT_BUF_TX_DATA_POOL_SIZE depending of net packet type.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use CONFIG_NET_TCP_INIT_RETRANSMISSION_TIMEOUT and
CONFIG_NET_TCP_RETRY_COUNT to control the total timeout at the TCP
level.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add section which explains how to configure PuTTY to use RTT
shell there with all shell features. There is an alternative
approach which also works but it does not allow to use all
shell features.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
RTT backend can only be called from thread context and immediate
logging might lead to interrupt context use. Previously this limitation
was implied in different way and commit (c88a9ef27) got reverted.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Make sure that the socket service is properly unregistered when
dispatcher is unregistered.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a separate test for public key validity. This needs to be done
synchronously so that we can respond with an early failure message to the
peer device.
Fixes#80218
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
If a shell command does not have a sub command, then the 3rd parameter
to SHELL_SUBCMD_ADD() macro should be set to NULL so that the help
will only print information specific to that command and not all
wifi commands.
Fixes#82633
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a separate entry for HTTP related code so that we can have
separate maintainers/collaborators than general networking area.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The tests overflowed system workqueue stack slightly when running on
nRF52840, increase the stack size globally for the tests to avoid
potential issues on other platforms as well.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When calling wifi_ap_disable() API specific WiFi driver implementation was
checked whether 'ap_enable' was provided, instead of 'ap_disable'. Fix
that copy-paste error.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Testcase uses certificates from the sample application at
samples/net/sockets/http_server. These were modified and moved into a
different folder by a previous commit, causing a build failure in the
test.
Testcase updated to:
- use new path to certificates
- update available cipher suites, since certificates now use ECDSA
- update expected hostname in certificate
The CA certificate in the sample app is also converted to .der format
for inclusion in the test (the content is exactly the same as the PEM
version, just converted to DER).
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
[Description]
PTS case: VCS/SR/SGGIT/CHA/BV-03-C fail.
[Root Cause]
VCS/SR/SGGIT/CHA/BV-03-C require Volume Flags Characteristic properties
(Read/Notify), but tester volume flags notify is disabled by default.
[Fix]
add CONFIG_BT_VCP_VOL_REND_VOL_FLAGS_NOTIFIABLE=y in
tests/bluetooth/tester/overlay-le-audio.conf
[Testing]
After modified, VCS/SR/SGGIT/CHA/BV-03-C pass with log:
Test Case Ended VCS/SR/SGGIT/CHA/BV-03-C PASS 24 00:00:01.010000
12/9/2024 11:31:55.027000 AM
Signed-off-by: Chang An <chang.an_1@nxp.com>
Configure the TE signal for the rw_rw612_bga board when using the
lcd_par_s035 shield. This signal should be handled on the rising edge in
the default configuration, since the display writes from the MCU are
faster than the panel reads data.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use the mipi_dbi_configure_te API within the st7796s display driver.
If the MIPI DBI controller supports the tearing enable signal, then
configure the ST7796S to output the TE line signal.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for the mipi_dbi_configure_te API within the NXP LCDIC
peripheral. Also, remove a redundant code patch in the write_command
function that was previously used to determine when the display driver
was writing to graphics RAM, as these writes should now be performed
using the mipi_dbi_write_display API.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Many MIPI DBI displays support a "tearing effect" signal, which can be
configured to signal each v-sync or h-sync interval. This signal can be
used by the MIPI DBI controller to synchronize writes with the
controller, and avoid tearing effects on the screen (which occur when
the write pointer from the MCU overlaps with the panel's read pointer in
the display controller's graphics RAM).
Add the `mipi_dbi_configure_te` API, which allows display controllers to
configure MIPI DBI controller to wait for a TE edge before streaming
display data. Allow the tearing enable parameters to be configured via
devicetree settings, since these will vary based on the MIPI DBI
controller and display controller in use.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename "nxp,kinetis-lpuart" compatible to "nxp,lpuart" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
This board has the required clock crystal (X4) and jumper settings
present to enable the USB 2.0 HS support.
* Enable the HSE clock (16MHz)
* Flip the PLL1 configuration over to use the HSE clock, but still
outputting 160MHz to sysclk/apbclk.
* Add the USB HS device tree node.
* Update the board documentation.
Signed-off-by: Adrian Chadd <adrian.chadd@meta.com>
Introduce new binding "st,stm32u5-otghs-phy" for OTG_HS PHY. This allows to
configure clock source and handle STM32U5 specific OTG_HS PHY behavior in
driver implementation in a more readable way.
Move OTG_HS PHY clock selection (previously <&rcc STM32_SRC_HSI48
ICKLK_SEL(0)>) from OTG_HS node to OTG_HS PHY node.
Rename USBPHYC_SEL -> OTGHS_SEL which matches the definition in the stm32u5
CCIPR2 register (RM0456 Rev 5, Section 11.8.47).
Support enabling OTG_HS PHY clock, which is bit 15 (OTGHSPHYEN) in
RCC_AHB2ENR1. Change OTG_HS clock to be bit 14 (OTGEN).
Calculate in runtime OTG_HS PHY clock source frequency. Try to match that
to supported (16, 19.2, 20, 24, 26, 32 MHz) frequencies and select proper
option with HAL_SYSCFG_SetOTGPHYReferenceClockSelection() API (instead of
hardcoded 16 MHz selection).
Co-authored-by: Adrian Chadd <adrian.chadd@meta.com>
Signed-off-by: Adrian Chadd <adrian.chadd@meta.com>
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Support specifying divided clock buses by introduction of
STM32_CLOCK_DIV(div) macro. This macro can be used in devicetree to define
clock source of peripherals.
HSE is selected in devicetree using:
<&rcc STM32_SRC_HSE ...>;
HSE/2 can now be selected with:
<&rcc (STM32_SRC_HSE | STM32_CLOCK_DIV(2)) ...>;
This allows to use clock_control_get_rate() API in peripherals in order to
get desired clock rate.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
in the switch case in the preceeding for loop if default path is taken
all the time, then the ret variable will stay uninitialized, the original
contributor of this driver has provided a comment that this path shall
never be reached, however, it is better to return an error code instead
of continuing with an incorrect configuration, hence this commit replaces
continue with a proper return errno.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Re-ran `clang-format` for consistent styling, simplified
multi-line statements, and consolidated string concatenations
where applicable.
This is a non-functional change focused on code formatting.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Catch the DTS warning by copying the SDRAM node in description:
unit address and first address in 'reg' (0xc000000) don't match for
/sdram@c0000000
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Added shell_device_get_binding() that wraps device_get_binding() plus
device_get_by_dt_nodelabel() so that a shell can easily get a device by
its full name or label.
Signed-off-by: Yishai Jaffe <yishai1999@gmail.com>
for the brevity renaming direction_gpios to dir_gpios since STEP/DIR
interface is quite an established term in context of stepper controllers.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
The current implementation of tmc2209 driver does not allow instantiation
of the driver without configuring msx pins.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
The SD physical layer specification requires that the operating supply
be stable for at least 1 millisecond before providing the required 74
clocks. The maximum VDD ramp time is specified at 35ms, giving a total
minimum delay of 36ms.
Signed-off-by: Jordan Yates <jordan@embeint.com>
