I don't have time to review the LED area in Zephyr,
so I step aside to make room for someone else.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Implement support for DNS Recursive Name option and use obtained
information to configure DNS resolver.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In case interface is UP, the interface is added to WPA supplicant in the
iface_wq itself and the max stack size is 4264, so, increase the stack
size of the iface_wq.
If the interface is added via net_mgmt thread then it works fine.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Fix compilation issues for SoftAP mode which were missed in the mode
specific code changes.
Signed-off-by: Sachin D Kulkarni <Sachin.Kulkarni@nordicsemi.no>
This commit adds initial support for the Adafruit MacroPad RP2040.
The board is based on the Raspberry Pi RP2040 microcontroller and
includes a 3x4 mechanical keyboard, 12 RGB NeoPixels, a rotary encoder
with push button, a 128x64 OLED display, and a small speaker for audio
feedback.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Make use of pm_device_driver_init to perform driver initialization.
Implement PM suspend and resume, which performs the following actions:
* Enables/disables the USART
* Gates the USART clock
* Configures USART pins
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Reuse the same peripheral init function between init and the
runtime configure API. Remove redundant enable calls, the init
function enables the USART internally.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Increase CONFIG_BT_BUF_CMD_TX_COUNT to avoid deadlock when running out
of buffers. See #77241 for the reference.
This fixes Mesh Provisioning Service tests (MESH/NODE/MPS).
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This commit adds HWINFO driver for MAX32 MCUs.
"z_impl_hwinfo_get_device_id" function is necessary for Zephyr USB
device stack.
Signed-off-by: Furkan Akkiz <hasanfurkan.akkiz@analog.com>
Different test layers need different stack sizes for BTP CMD thread
and also AutoPTS might need to overwrite this config based on test
case.
Increase the stack size for mesh tests.
Signed-off-by: alperen sener <alperen.sener@nordicsemi.no>
There's nothing in RFC 2131 or RFC 8415 that would mandate the DHCP
server to reply with a source port set to the IANA assigned one, and
some servers seem to send responses with some arbitrary source port set.
Therefore, make Zephyr's DHCP client implementation more permissive,
accepting packets with a source port set to a different port than the
IANA assigned server port.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Implementation of chan_filter and chan_release allows to maintain
synchronization about DMA channel allocation between hal DMA driver and
zephyr DMA driver.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Update Cmake to include hal EMDRV header
It also adds dmadrv source when CONFIG_SOC_GECKO_LDMA is selected
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
The LED 4 is connected to the STMPS2151STR on the FAULT output pin which
is pulled low, automatically turning on the LED, in case of current
limit faults. Therefore, pin D4 should not be configured as a LED but
rather as an input to detect the fault condition.
Additionally, it should be noted that the board's silkscreen labels this
LED as "OC" (OverCurrent) rather than usr{1,2,3}, as is the case for the
other LEDs described in the DTS.
Fixes: cc5ae49133
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This commit fixes the bug that the memory of the work request is
freed up in the work handler, before it is not needed anymore by the p4wq.
This is fixed now, by using the new done_handler in the p4wq
for freeing up that memory.
Signed-off-by: Florian Weber <Florian.Weber@live.de>
Add an optional handler to the p4wq to give the submitting code
(e.g. rtio workq) a possibility execute code after the work was
succesfully executed.
Signed-off-by: Florian Weber <Florian.Weber@live.de>
Added timer3 and pwmleds configuration to the nucleo_wba55cg board DTS
file. This includes setting the prescaler, enabling the pwm3 node with the
appropriate pin control settings, and configuring the pwmleds node with
green_pwm_led.
Signed-off-by: Lubos Koudelka <lubos.koudelka@st.com>
The driver already read the speed flags (cfr. ospeed) and called
LL_GPIO_SetPinSpeed, but these flags could not be set yet.
Signed-off-by: Jaro Van Landschoot <jaro.vanlandschoot@basalte.be>
Fix to release aux context stored in node rx, and not in the
superior scan or sync context as the one in the superior scan
or sync context could be reset or have a different new aux
context when multiple advertising chain reception is used.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix assertion due to changes introduced to support multiple
advertising chain reception.
Auxiliary context association with the Periodic Sync context
was not cleared due to which when terminating a Periodic
Synchronization triggered an assertion check, under race
conditions, detecting that the auxiliary context was already
released.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The BLE acronym is not an official description of Bluetooth
LE, and the Bluetooth SIG only ever refers to it as Bluetooth
Low Energy or Bluetooth LE, so Zephyr should as well.
This commit does not change any board or vendor specific
documentation, and the term BLE may still be used in those.
It will be up to the vendors to update it if they want,
since many of them are using the term BLE in their
products.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The BLE acronym is not an official description of Bluetooth
LE, and the Bluetooth SIG only ever refers to it as Bluetooth
Low Energy or Bluetooth LE, so Zephyr should as well.
This commit does not change any board or vendor specific
samples, and the term BLE may still be used in those.
It will be up to the vendors to update it if they want,
since many of them are using the term BLE in their
products.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The BLE acronym is not an official description of Bluetooth
LE, and the Bluetooth SIG only ever refers to it as Bluetooth
Low Energy or Bluetooth LE, so Zephyr should as well.
This commit does not change any board or vendor specific
documentation, and the term BLE may still be used in those.
It will be up to the vendors to update it if they want,
since many of them are using the term BLE in their
products.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Fix missing sync_delay and transport_latency information in HCI
LE BIG Complete event.
Relates to commit 1a640e4711 ("Bluetooth: controller:
Included transport latency in LE_Big_Established").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In ap enable cmd, channel set to 0 means ACS mode.
Remove hostapd AP macro for this case to make ACS mode
available for public usage.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
Prior to this change a wrap of the completion count (without SUBMIT_SEM)
would result in looping indefinitely waiting for completions.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add a test for the behaviour of `rtio_submit` with
`CONFIG_RTIO_SUBMIT_SEM=n` when the `cq_count` variable overflows.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Fix incorrect device address reported in the LE Periodic
Advertising Sync Established event when using Periodic
Advertiser List.
During Extended Scanning there can be an ADV_EXT_IND PDU
received between currently being received ADV_EXT_IND PDU
and AUX_ADV_IND PDU; if the one received between has an
address match then incorrectly the Periodic Synchronization
was established to the device whos AUX_ADV_IND PDU is being
received. Fix by storing the auxiliary context that has the
address match and compare with it when matching the SID in
SyncInfo of AUX_ADV_IND PDU being received prior to creating
the synchronization.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix BT_CTLR_LOW_LAT_ULL conditional compilation code by
decoupling it from BT_CTLR_LOW_LAT code.
BT_CTLR_LOW_LAT_ULL makes ULL execution context to tailchain
in comparison to continuously process in a while loop.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
