This patch fixes a couple of syntax issues that lead to incorrectly
rendered content:
- Bad list indentation
- Missing blank line between list item and sub-item.
Also made 'label' a literal.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fix incorrect use of stream handle instead of connection
handle to enqueue Tx ISO Data, and use stream index to get
stream instance.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Twister detects FLASH overflow and skips tests that trigger that
condition by default, but sometimes images are just on the flash size
limit and then overflows at a later stage when imgtool adds a trailer,
which gets detected as a build fail and fails the run.
This detects the imgtool flash overflow together with the normal build
ones, causing the build to be skipped on imgtool flash overflow as well.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
More GigaDevice support added, include drivers, boards, etc.
Also, some known issue has been fixed.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
When the node is part of only one subnet, it starts Network ID
advertisements with infinite timeout. It is not an issue when using
legacy advertising and extended advertising with shared set for local
messages and GATT because any message will stop advertisements. However,
when a separate adv set is used for GATT advertisements,
`struct bt_le_ext_adv_cb.start` callback won't be called, but the
implementation relies on that callback to switch to a next subnet.
Calling `bt_mesh_adv_gatt_update()` stop GATT advertisement so that the
implementation can switch to the next subnet.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Reduce advertising duration to `max_timeout` when advertising node
identity for multiple subnets. This will let the node to interleave
subnets for NODE_ID_TIMEOUT.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
`struct bt_le_ext_adv_start_param.timeout` resolution is in 10ms. When
duration is less than 10ms, division will be evaluated to zero, which
will result in indefinite timeout. Set timeout to 10ms to avoid
indefinite timeout. The advertisement will end earlier anyway after the
event is finished.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This adds bits about PECI drivers:
* Devicetree binding changes for the ITE it8xxx2 driver.
* New driver for Nuvoton NPCX.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a few bits about the new I3C controller API,
a new controller driver, and about extending an existing
sensor driver for I3C.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The note refers to the wrong API, that has been replaced by a pinctrl
call, update the comment.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The one in esp32_net_defconfig is redundant and lpcxpresso51u68 is not
really using any of the pinmux api, so that can go as well.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add code to handle parsing the gpio-reserved-ranges property present on
iMX GPIO controllers, so that gpio controllers with gaps in their pin
indexing can still have pinmux settings applied correctly.
Fixes#50142
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add gpio-reserved-ranges property to gpio controllers on RT10xx devices
that have gaps in their GPIO numbering.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
...Z_THREAD_STACK_BUFFER.
This is currently a symbolic change as Z_THREAD_STACK_BUFFER
is simply an alias to Z_KERNEL_STACK_BUFFER without userspace,
and Xtensa does not support userspace at the moment.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
...Z_THREAD_STACK_BUFFER.
This is currently a symbolic change as Z_THREAD_STACK_BUFFER
is simply an alias to Z_KERNEL_STACK_BUFFER without userspace,
and Xtensa does not support userspace at the moment.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Zephyr timer is based on system ticks, there usually exists some time drift
due to round up/down errors between cycles, ticks and time delay, we
need to add those expected time drift into the bound calculation for
running this test.
Add a new config TIMER_TEST_PERIOD_MAX_DRIFT_PERCENT for users to set
expected maximum drift percentage for the timer period.
Signed-off-by: Chen Peng1 <peng1.chen@intel.com>
Tickless test enables PM which implies use of LPTIM as ticker on STM32
platforms.
Specifically on nucleo_l073rz, this configuration is fragile as only
LSI(37KHz) could be used as LPTIM tick source, whith a huge accuracy
tolerance (20%).
This works on most cases, when a specific tick freq (4000 ticks/sec),
but this tests explicitly requires tick frequency set to 100.
Excludes nucleo_l073rz for this test.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
A specific check is implemented lptim driver in order to ensure global
platform clock/tick configuration is in line with recommendations.
To respect portability principles, don't error out when a config
conflict is detected but generates a warning instead.
Also, since these are only recommendations, provide an option to override
the check. Besides automatically override when ZTEST is enabled, as some
kernel tests specifically configure tick freq to 100.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The test case was originally designed for the coverage of
nop()/arch_nop() function. It is not very meaningful for
testing something but causing lots of false alarms on the
kernel/common test so far. Suggest removing this test case.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
A workaround to exclude boards from twister. Other solutions do not work,
setting twister fields to false in the board yaml file is not enough,
given that this board has many associated samples and tests, so it can't
be disabled on its own.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Pinctrl API has taken over pinmux. As planned, pinmux is going to be
deprecated for the next release (3.2). This patch flags all pinmux APIs
as deprecated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
remove pinmux support in mec15xxevb and mec1501modular
boards. pinmux API is deprecated in 3.2 release.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 qmspi. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 adc. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 pwm. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 espi. Update board dts, pinmux and espi driver
files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 tach. Update board dts and pinmux files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 peci. Update board dts and pinmux files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 pwm. Update board dts and pinmux files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 kscan. Update board dts and pinmux files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 ps2. Update board dts and pinmux files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Fixes an issue with img_mgmt whereby the if check for a slot3
partition is using the wrong case for the partition name.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
