Default config should have all bells and whistles enabled to minimize
number of overlays needed in autopts.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Adds a note on a fixed issue whereby the latest Zephyr SDK
toolchain was not used depending upon hash values in the cmake
registry.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This improves the version checking for the zephyr SDK by searching
for newer versions that the version that was detected. This works
around the issue whereby the versions are contained in files with
MD5 hashes which might be in any order.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Follow-up: #53124
The PR#53124 fixed an issue where the variable `check` was not properly
dereferenced into the correct variable name for return value storage.
This was corrected in 04a27651ea.
However, some code was passing a return argument as:
`zephyr_check_compiler_flag(... ${check})`
but checking the result like:
`if(${check})`
thus relying on a faulty behavior of code updating `check` and not the
`${check}` variable.
Fix this by updating to use `${${check}}` as that will point to the
correct return value.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Make sure that the interrupt and event routing enable bits have the
reset values in case the Zephyr firmware image is chain-loaded.
When started by MCUboot, these registers values aren't the reset values,
but then Zephyr initializes them in same way. Yet, when the Zephyr
firmware image is chain-loaded by nRF5 bootloader, they may have values
that cause the scheduler to behave in unexpected ways.
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
Add support for the Arduino GIGA board, an STM32H747XI based development
board in Arduino form factor, featuring external flash, SDRAM, Bluetooth
and WiFi.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Allow to register a callback function which is called when a firmware
update is canceled by the cancel command.
Signed-off-by: Marc Lasch <marc.lasch@husqvarnagroup.com>
If an event with corrupted length arrives, the extra check makes the
handler return early to avoid reading data out of bounds.
Signed-off-by: Arkadiusz Kozdra <akozdra@antmicro.com>
These are RT1060 based boards that use the flash for XIP, the bus
(nxp,imx-flexspi) lives under memc or flash. Declaring the flash as
"jedec,spi-nor" causes the SPI NOR driver to create an instance for it,
but then there's no bus and the build fails.
Dropping the spi-nor compatible seems to fix the problem.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
When possible re-use the already allocated RX node for notifications.
Store (retain) RX node and Link element on RX if NTF could occur.
Pass link element to LLCP (ull_cp_rx()) together with RX node.
New RX node type RETAIN introduced to signal retention
When no RX node is available allocate one and hold off TX on procedures
until such time that a node is available for NTF.
In case waiting for NTF buffer avail is needed, allocate and store TX
node to use for TX once NTF becomes available.
CIS Established (incl. timeout handling) is now handled entirely as a
specific event driven by ull_conn_iso - ie removal of procedure check
of cis->established and cis->expire, as this is doubling mechanism
in the conn_iso context.
Unit test and helpers updated to handle new node type.
Function ull_cp_release_ntf() was used only in unit test, so moved to
helper context.
Updating release_ntf to handle the fact that with piggy-backing in test
context the node used for NTF can be from two different memory pools
Signed-off-by: Erik Brockhoff <erbr@oticon.com>
When doing "bt connections" the currently selected ACL (default_conn)
is now indicated with a "*" making it easier to determine which
of the connections is currently selected.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Use internal constant ZSOCK_POLLIN instead of POLLIN to
make the http_client source file compile without error with
CONFIG_NET_SOCKETS_POSIX_NAMES disabled.
Fixes#55423
Signed-off-by: Lucas Dietrich <ld.adecy@gmail.com>
A new Z_SPIN_DELAY() macro has been added which
can be used to reduce a bit the amount of noise
due to the POSIX arch need to break busy loops with
k_busy_wait().
Use it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add support for RT595 EVK to display sample using RM68200 based MIPI
panel. The board is configured with an increased heap size to account
for the panel's high resolution.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add configuration for RM68200 MIPI display. This display
controller drives a 1280x720 LCD display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add clock initialization for MIPI and LCIDF to NXP RT5xx SOC.
Note that clock divider properties are used by both initialization
routines, as the required clock divider will vary depending on
attached display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix support for GT911 touchscreen driver when not using interrupt.
The controller still requires that the INT pin be set to input in
order to correctly respond to I2C queries.
Also, the GT911 requires that the INT pin is not configured until the
RESET pin has been low at least 10 ms after reset, so add an additional
delay during initialization to account for this.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add clock rate definitions for MIPI and LCDIF peripherals, to enable
retrival of these peripheral clock rates at runtime.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for NXP DCNANO LCDIF (lcd interface) peripheral,
present on iMX.RT500. Currently this driver only supports updating
the primary framebuffer, and does not implement support for the cursor
buffer present on this IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for MCUX MIPI DSI 2L. This IP block differs slightly from
the existing MCUX MIPI peripheral, and uses a different hardware
abstraction layer. For these reasons, a new driver was introduced rather
than extending the existing mcux_dsi implementation.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Allow configuration of AHB RX buffer allocation. This allows sections
of the AHB RX buffer to be reserved for specific masters, which can
enhance performance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Crypto test-case 221 has a false negative, not passing because the ECC
family is disabled, not because of the key length.
Increase the timeout for the nRF5340/nRF9160 devices.
RSA keygen will sometimes take more than 90 seconds
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
STM32L432 SDMMC issue
RM0394 :SDMMC
Not available on STM32L42xxx, STM32L432xx and STM32L442xx devices.
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
This is a follow-up to commit 7195db01f4.
Restore the check that was accidentaliy removed in the above commit,
so that the message is again logged only once per detection of the
anomaly 160 conditions.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
WAIT_FOR is a busy wait loop, which in the POSIX ARCH
should include a very minor delay in each iteration.
After this fix, tests/lib/sys_util does not need to
exclude native_posix anymore.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
In the POSIX ARCH, code takes zero time to execute,
so busy wait loops become infinite loops, unless we
force the loop to take a bit of time.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The driver utilizes ST Microelectronics library (which
exists in modules\hal\st\sensor\vl53l1x. Platform specific
headers and source files used by the library are included
and adapted for Zephyr.
The driver can be configured in proj.conf to use a
interrupt/polling methods and the use of the XSHUT pin on
the VL53L1X. All uses were tested successfully.
Signed-off-by: Mark Watson <mwatson@prosaris.ca>
Those files includes soc.h header which exists not for all boards.
soc.h consists soc-depended defenitions and need to be included by
soc-depended sources
Signed-off-by: Dmytro Semenets <dmytro_semenets@epam.com>
After the introduction of the renesas smartbond family the scope of dts
files needs to be limited to the rcar subfolder.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add myself as maintainer of hash utilities which currently
encompasses hash functions and hash maps (hash tables).
Signed-off-by: Chris Friedt <cfriedt@meta.com>
The same k_busy_wait needed for native_posix is needed for
all POSIX arch platforms.
Also increase that busy wait a bit. There is no point of
waiting for just 1 microsecond at a time, and waiting a bit
longer speeds up the test.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
nrf51 has been discontinued. There is no reason to support
ble mesh tests for nrf51 DK platform. As alternative support
of nrf52840 has been added if there wasn't before.
Also, microbit lacks significant amount of RAM (about 800 bytes)
to build mesh test.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
nrf51 has been discontinued. There is no reason to support
ble mesh as well as new mesh features and fitting of samples
for nrf51 DK platforms. As alternative support of nrf52840
has been added if there wasn't before.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Test is checking behavior of compile time macros used for generation
of log messages thus if platform enforces runtime approach does macros
are not available and complilation fails.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Combining CONFIG_LOG_OUTPUT_FORMAT_LINUX_TIMESTAMP and
CONFIG_LOG_TIMESTAMP_64BIT results in a wrong timestamp, as the
Linux timestamp format print call assumes a 32 bit variable for
the seconds. Fix it by using a different print format for 64 bit
timestamps.
Fixes: #55372
Signed-off-by: Martin Sollie <ms@aziwell.no>
This patch adds watchdog driver for Renesas Smartbond SOCs.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds driver for SmartBond TRNG peripheral that with separate
ISR an thread data pools.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
