lib/ was starting to get messy and inconsitent. Files being either
dumped in the root or in sub-directories without a clear plan.
Move all library components into one single folder and call it 'os'.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We have dependency on this module in code which is part of Zephyr. When
this module is split out of the tree we need to be able to build. Move
this Kconfig part to be part of zephyr and keep the external code in
ext/ with plan to split it out on the future.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Extend generic mbedTLS configuration file with MBEDTLS_AES_ROM_TABLES
option. This allows to save some RAM (~8kB) in favour of ROM and
performance.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Running sanitycheck from Windows is not supported yet. Unfortunately,
the error message is obscure when a user is unaware of this and runs
it from Windows anyway.
This patch gives an easy to understand error message explaining this
issue.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Out-of-tree doc builds rely on extract__content.py to copy needed
content from the source folders to the build folders. To minimize what's
copied, all the reST files are copied plus files referenced by the reST
files. The extract_content.py script does a pattern match scan for
directives that reference other files (e.g., .. image::) and copies the
referenced file. It's not a smart parser though and doesn't ignore
directives in comments or in code-blocks. Rather than teaching the
script how to properly parse reST files, we'll just change the example
(in a code-block) to reference an existing image.
Fixes: #12621
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
It was reported, and confirmed by multiple parties that default
CONFIG_ETH_MCUX_RX_BUFFERS=2 under some packet load leads to
1s and increasing packet processing delay and eventual deadlock.
No reports were about CONFIG_ETH_MCUX_TX_BUFFERS=2, but be on safe
side and just set that to the minimal value as the current default,
to allow us to have good conservative base to test various networking
stack issues.
Fixes: #3132
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Correct it so that it is possible to use PWMs on nRF9160 as well,
not only on nRF5 family SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Minor adjustments are done to the nRF clock_control and rtc_timer
drivers to make them usable on nRF9160 as well.
The arm_irq_vector_table test code is modified only because it uses
the function that has been renamed in the nrf_rtc_timer driver.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the symbol generated from DT so that it is common for nRF9160
and nRF5 family SoCs. To avoid artificial renaming of CLOCK_POWER_IRQn
to POWER_CLOCK_IRQn.
For nRF5 family SoCs clock nodes were not defined so far, thus they are
added so that the proper DT symbol is generated for them as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add the header file with the nrfx drivers configuration suitable for
the nRF9160 SoC. This file contains also definitions of CMSIS symbols
(like NRF_CLOCK or NRF_SPIM0) for structures of peripheral registers.
These symbols are used in nrfx HALs and drivers, and for other nRF SoCs
they come from MDK files. For nRF9160 they need to be mapped to proper
addresses in Secure or Non-Secure domain, so we use the information
coming from DT to get it done automatically.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add missing node for instance 0 of the RTC peripheral and use an alias
to the flash-controller node instead of the nvmc node definition (there
is no need to have a separate node just to get the NVMC base address).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
mps2_an385 is enabled for networking -> default networking is SLIP ->
SLIP selects UART_PIPE -> UART_PIPE requires UART_PIPE_ON_DEV defined
-> undefined leads to error on building some samples.
Fix all of these issues.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add overlays for commonly used socket samples: big_http_download and
dumb_http_server. Can be used with:
make BOARD=mps2_an385 CONF_FILE="prj.conf overlay-smsc911x.conf"
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Board can be emulated in QEMU, so select QEMU_TARGET as required for
various bits of "make run" magic to work.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
As emulated by QEMU. SMSC9118 is compatible with SMSC9220 as used in
ARM MPS2 board, as well as SMSC9115/6/7/etc. devices.
Portions of the code are based on mbedOS code from its
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/drivers/smsc9220_eth.c
eth_smsc9220_priv.h originally comes from Arm mbedOS file:
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/drivers/smsc9220_eth.h
augmented with struct & defines from:
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/CM3DS.h
and renamed as eth_smsc911x_priv.h to follow Zephyr conventions.
Then, following changes applied:
Changes to build under Zephyr, changes to use symbolic constants
and field access helpers, typo fixes, etc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The board has SMSC LAN9220 (actually as an "IP core" in an
FPGA-emulated SoC). The patch includes DTS bindings for this device.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
There is an effort underway to make most of the Zephyr build script's
reentrant. Meaning, the build scripts can be executed multiple times
during the same CMake invocation.
Reentrancy enables several use-cases, the motivating one is the
ability to build several Zephyr executables, or images, for instance a
bootloader and an application.
For build scripts to be reentrant they cannot be directly referencing
global variables, like target names, but must instead reference
variables, which can vary from entry to entry.
Therefore, in this patch, we replace global targets with variables.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
There is an effort underway to make most of the Zephyr build script's
reentrant. Meaning, the build scripts can be executed multiple times
during the same CMake invocation.
Reentrancy enables several use-cases, the motivating one is the
ability to build several Zephyr executables, or images, for instance a
bootloader and an application.
For build scripts to be reentrant they cannot be directly referencing
global variables, like target names, but must instead reference
variables, which can vary from entry to entry.
Therefore, in this patch, we replace global targets with variables.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The eswifi controller is capable of acting as an Access Point.
Implement ap_enable/ap_disable methods.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Create eswifi_at_cmd and eswifi_at_cmd_rsp helpers, allowing to send an
at command and parse the at response. These methods return success if
the response contains the OK* string. The eswifi_at_cmd_rsp method
extracts response content/size (DATA) on success.
*Response format is:
\r\n[DATA]\r\nOK\r\n>
Where DATA can be arbitrary (ASCII or not).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Split out the boards that utilize the FRDM-KW41Z as a seperate test
where we explicitly set the shield as an extra_args instead of having to
do it in the CMakeLists.txt file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Incoming updates to the nRF clock driver require some extra enum
definitions from the nRFx HAL which were not available in HW
model versions before 1.4 => update it.
Also as the nrf52_bsim does not yet support DTS, include a define
for the clock IRQ interrupt number (as the new clock driver will
be using the DTS macro instead of the nRF MDK value.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Add information about image size recommendations, and add some more
details about other reST features such as tables. Also added a flow
picture to the documentation generation doc.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Prolong by 1 second the BT encrypted connection test, to ensure
there is enough time for the link itself to be encrypted.
Before this change the key was exchanged, but the 1st notification
(pass condition) was received before the link itself was encrypted.
With this change we wait for 1 notification more (1 second more),
and during that extra second the link is actually encrypted.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
board.h does not exist for any of the (official) Nordic nRF
boards. This commit corrects the information about the source
ofthe button and LED definitions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove redundant inclusion of nrf.h (included by nrfx.h).
Group the logging/log.h inclusion together with the other
inclusions in this file (make inclusions' list look as in
nrf9160/soc.c).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove the locally-defined macros which define the base
addresses for XICR, Peripheral space and PPB. The macros
are not used.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove all references in the documentation and Kconfig options
to the legacy shell to avoid confusing users and developers
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Rather than specifying SHIELD via Kconfig, we move it to being
specified via the command line, similar to board.
So we can do:
-DSHIELD=x_nucleo_iks01a1
or, for multiple shields:
-DSHIELD="x_nucleo_iks01a1 frdm_kw41z"
Following cmake change, update x_nucleo_iks01a1 sample in order
not to enable CONFIG option anymore but set SHIELD cmake option.
Last, update documentation to reflect this change.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
