The watchdog peripheral on SAME5x/SAMD5x MCUs is very simmilar
to the one found on the SAMD2x parts with only a few register
names changed.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
move watchdog.h to drivers/watchdog.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
- Even one-liner statement if () need { }
- you can coalesce assignment and condition if the later tests the
earlier only.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The upper limit of the timeout should not be 0.
tests/drivers/watchdog/wdt_basic_api checks for this and fails as the
driver currently only checks that the timout does not exceed the upper
bound.
This also makes it check the lower bound, so that the test passes.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Convert the Atmel SAM0 watchdog driver to the new watchdog API and
enable DTS support.
This fixes#10914.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Each driver seemed to use their own Kconfig option to set the name for
their drivers. This makes writing example/test code difficult as each
one of them will have to special case for each of the supported
platforms.
Use a consistent CONFIG_WDT_0_NAME option in all drivers.
Fixes#8094.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
New API enables setting watchdog timeout in the unit of microseconds.
It is possible to configure watchdog timer behavior in CPU sleep state
as well as when it is halted by the debugger.
It supports watchdogs with multiple reload channels.
Jira: ZEP-2564
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
