Looking at the data sheet for the npcx section 4.15.5 CR_UART Core
Registers, the UICTRL register that is used in the npcx poll
functions is invalid when running in FIFO mode. Instead, calls to
uart_npcx_poll_in and uart_npcx_poll_out should be redirected to
their respective FIFO read/fill functions (when using interrupts).
Changes:
- When calling uart_poll_in: forward the request to uart_fifo_read.
- When calling uart_poll_out: loop until uart_fifo_fill returns
non-0 (we wrote 1 byte).
Signed-off-by: Yuval Peress <peress@chromium.org>
Simple reorg of the function declarations. This change moves
the interrupt driven functions declared at the bottom of the
uart_npcx.c file to the top, clustered under the same ifdef.
Signed-off-by: Yuval Peress <peress@chromium.org>
Current implementation of uart_npcx_irq_{tx,rx}_ready always returns
false if the respective interrupt enable bit is not set, which means
that the api cannot be used if the interrupts are temporarily disabled
for whatever reasons, breaking patterns such as [1].
Other uart drivers also seems to not have this check, this patch removes
it from the NPCX driver too.
[1] https://github.com/zephyrproject-rtos/zephyr/blob/master/drivers/console/uart_console.c#L549
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Since the uart device clock will be stopped after ec entered sleep or
deep sleep state and restore its clock automatically, there is no need
to implement code for suspending and resuming devices manually.
The driver still needs to check the current status of uart device when
it wants to change its power state to LOW or SUSPEND power state. It is
crucial to forbid ec enters sleep or deep sleep state when uart device
is busy with transmitting data. Or we will observe broken characters on
the uart console.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces power management driver that improves the efficiency
of ec operation by adjusting the chip’s power consumption to the level
of activity required by the application in npcx series.
The following list summarizes the main properties of the various chip
power states. Please refer the power.c file for more detail.
Main power states in npcx series include:
- Active: Core, RAM and modules operate at the clocks generated by PLL.
- Idle: Enter this state when the Core executes WFI or WFE instruction.
- Sleep: clock is stopped for most of modules but PLL is enabled.
- Deep Sleep: As Sleep mode but PLL is disabled.
- Standby: All power rails are turned off besides standby and battery
power rails.
And this CL implements one power state, PM_STATE_SUSPEND_TO_IDLE, with
two sub-states for Zephyr power management system.
Sub-state 0 - "Deep Sleep" mode with “Instant” wake-up if residency
time is greater or equal to 1 ms
Sub-state 1 - "Deep Sleep" mode with "Standard" wake-up if residency
time is greater or equal to 201 ms
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Remove conditionals (PM_DEEP_SLEEP_STATES and PM_SLEEP_STATES) from
power management code. Now these features are always available when
power management is enabled.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL replaces all DT_ prefix with NPCX_DT_ for all macros used
for providing npcx device information in soc_dt.h It avoided the
ambiguity with the DT_ prefix for system DT macros/defines.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add const modifier for hal instances, clock devices pointer, and module
base address in npcx drivers to prevent driver functions change them
unexpectedly.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Replace all calls to the assert macro that comes from libc by calls to
__ASSERT_NO_MSG(). This is usefull as the former might be different
depending on the libc used and the later can be customized to reduce
flash footprint.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
This CL adds more comments for each macro functions used for device tree
file for better explanations. It also changes all hex values in soc.c to
lower case.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Fixed 'line length exceeds 80 columns' warning by shortening the clock
controller device name from NPCX_CLOCK_CONTROL_NAME to
NPCX_CLK_CTRL_NAME.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
These are all the case that coccinelle cannot find as they are inside
macro declarations.
Fixed via:
git grep -rlz -E "\(struct device \*" |
xargs -0 sed -i 's/(struct device/(const struct device/g'
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This CL configures the UART wake-up event triggered from a falling edge
(START condition) on CR_SIN pin. It also includes:
1. Introduce wui_maps property in yaml file to present relationship
between Wake-Up Input (WUI) and UART device.
2. Implement wake-up mechanism by MIWU api functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
