Changes twister tests and nrf samples from using legacy adv to ext adv
since this is the default for Mesh. Legacy adv is still tested in bsim.
Removes redundant test configuration testing ext adv.
Removes redundant config for ext_adv in `multi_ext_adv.conf`.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
The naming of these two options was problematic, since it's both of them
are about vendor extensions, even though one has _EXT in the name and
the other doesn't. Just merge one option into the other. This has a
slight overhead on the controller side of enabling some more vendor
features if BT_HCI_VS is enabled, but that should hopefully be
acceptable.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
The commit adds dependency on Kconfig FLASH_PAGE_LAYOUT to subsystems
that really require it:
FCB, NVS, LittleFS
and removes direct selection from '*.conf' files where no longer
needed.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Remove usage of Kconfig symbol `CONFIG_BT_DEBUG_LOG` from samples. It
has been deprecated since this PR:
https://github.com/zephyrproject-rtos/zephyr/pull/56183
The Kconfig symbols has been replaced by `CONFIG_LOG=y` on most of the
cases. Or it has been removed when not needed anymore.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
The `bluetooth/common/log.h` and `bluetooth/common/log.c` files have been
removed. Files that were using them have been updated to use
`zephyr/logging/log.h` instead.
Those replacement have been done consequently:
- `/BT_DBG/LOG_DBG/`
- `/BT_ERR/LOG_ERR/`
- `/BT_WARN/LOG_WRN/`
- `/BT_INFO/LOG_INF/`
- `/BT_HEXDUMP_DBG/LOG_HEXDUMP_DBG/`
- `/BT_DBG_OBJ_ID/LOG_DBG_OBJ_ID/`
Also, some files were relying on the `common/log.h` include to include
`zephyr/bluetooth/hci.h`, in those cases the include of `hci.h` has
been added.
For files that were including `common/log.h` but not using any logs,
the include has been removed and not replaced.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Refactor and simplify the bluetooth buffer configurations to improve the
easy of configurations and eliminate invalid ones.
By moving configurations out of host and controller specific
configurations and into a common one it becomes easier to configure
the host and controller separately as the same configurations can be
used as would be for a combined build.
All HCI configurations are now given exluding the matching HCI header,
which eases the configuration as the application don't have to know the
different header sizes.
The BT_RX_BUF_LEN is split into ACL and Event, as well as the suprising
use of Command size.
BT_L2CAP_RX_MTU is removed as the stack does not support reassembling of
HCI ACL data to larger L2CAP PDUs. The application will have to set
ACL RX size and account for the L2CAP PDU header itself.
BT_EATT_RX_MTU was removed as it is only used for setting a different
default value for another option which leads to the stuck kconfig symbol
problem.
The configurations can be updated according to the table below:
** New configuration | ** Old configuration
All configurations
BT_BUF_ACL_RX_SIZE | BT_L2CAP_RX_MTU + 4
BT_BUF_ACL_RX_SIZE | BT_RX_BUF_LEN - 4
BT_BUF_EVT_RX_SIZE | BT_RX_BUF_LEN - 2
BT_BUF_CMD_TX_SIZE | BT_RX_BUF_LEN - 3
BT_BUF_CMD_TX_COUNT | BT_HCI_CMD_COUNT
BT_BUF_EVT_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_ACL_RX_COUNT
BT_BUF_EVT_DISCARDABLE_SIZE | BT_DISCARDABLE_BUF_SIZE - 2
BT_BUF_EVT_DISCARDABLE_COUNT | BT_DISCARDABLE_BUF_COUNT
Controller-build
BT_BUF_ACL_TX_SIZE | BT_CTLR_TX_BUFFERS_SIZE
BT_BUF_ACL_TX_COUNT | BT_CTLR_TX_BUFFER
HCI-bridge
BT_BUF_ACL_TX_SIZE | BT_HCI_ACL_DATA_SIZE
BT_BUF_ACL_TX_COUNT | 6
Fixed invalid configurations setting either BT_L2CAP_RX_MTU or
BT_CTLR_DATA_LENGTH_MAX larger than BT_RX_BUF_LEN could lead to buffer
overruns.
Fix advertising report max data length calculation.
This always used the BT_DISCARDABLE_BUF_SIZE macro but this feature
can be turned off and advertising reports will be allocated from the RX
buffer in that case. Also controller-build does not have this buffer
(in hci_raw.c). Also the wrong HCI header was used in the calculation,
HCI event header should have been used instead of HCI ACL header.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
There is a choice to log btmon logs over UART or RTT.
You can choose number of RTT buffer, set its name and size.
Replaced CONFIG_BT_DEBUG_MONITOR with CONFIG_BT_DEBUG_MONITOR_UART
for UART usage and CONFIG_BT_DEBUG_MONITOR_RTT for RTT.
Signed-off-by: Magdalena Kasenberg <magdalena.kasenberg@codecoup.pl>
Moves mesh feature configuration to a separate module, deprecating the
bt_mesh_cfg_srv structure. The initial values for the features should
now be enabled through KConfig, where new config entries have been added
for each feature.
This removes the upward dependency on the config server from the core
stack, and makes the config server a pure frontend for the configuration
states, as all spec mandated behavior around the feature states is now
encapsulated.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The following samples:
- boards/nrf91/nrfx
- boards/nrf52/power_mgr
are actually not specific to nRF91 and nRF52 Series SoCs, respectively,
hence the current naming of the above board/ subdirectories may be
misleading. Thus, use nrf/ directory for holding all nRF board specific
samples that apply to several boards.
Paths to the moved samples that are mentioned in their documentation
are also updated accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2019-12-09 16:10:19 +01:00
Renamed from samples/boards/nrf52/mesh/onoff-app/prj.conf (Browse further)
