d3ea66d493
The following samples: - boards/nrf91/nrfx - boards/nrf52/power_mgr are actually not specific to nRF91 and nRF52 Series SoCs, respectively, hence the current naming of the above board/ subdirectories may be misleading. Thus, use nrf/ directory for holding all nRF board specific samples that apply to several boards. Paths to the moved samples that are mentioned in their documentation are also updated accordingly. Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
103 lines
2.2 KiB
Text
103 lines
2.2 KiB
Text
#CONFIG_INIT_STACKS=y # if set, lots of noise from mesh/adv.c: STACK_ANALYZE
|
|
CONFIG_MAIN_STACK_SIZE=512
|
|
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048
|
|
|
|
CONFIG_GPIO=y
|
|
|
|
CONFIG_BT_SETTINGS=y
|
|
CONFIG_FLASH=y
|
|
CONFIG_FLASH_PAGE_LAYOUT=y
|
|
CONFIG_FLASH_MAP=y
|
|
CONFIG_NVS=y
|
|
CONFIG_SETTINGS=y
|
|
CONFIG_BT_MESH_RPL_STORE_TIMEOUT=600
|
|
|
|
CONFIG_BOOT_BANNER=y
|
|
|
|
CONFIG_BT_OBSERVER=y
|
|
CONFIG_BT_BROADCASTER=y
|
|
CONFIG_BT_CTLR_DUP_FILTER_LEN=0
|
|
CONFIG_BT_CTLR_LE_ENC=n
|
|
CONFIG_BT_CTLR_LE_PING=n
|
|
CONFIG_BT_DATA_LEN_UPDATE=n
|
|
CONFIG_BT_PHY_UPDATE=n
|
|
CONFIG_BT_CTLR_CHAN_SEL_2=n
|
|
CONFIG_BT_CTLR_MIN_USED_CHAN=n
|
|
CONFIG_BT_CTLR_ADV_EXT=n
|
|
CONFIG_BT_CTLR_PRIVACY=n
|
|
|
|
CONFIG_BT_PERIPHERAL=y
|
|
|
|
CONFIG_BT=y
|
|
CONFIG_BT_TINYCRYPT_ECC=y
|
|
CONFIG_BT_L2CAP_RX_MTU=69
|
|
CONFIG_BT_L2CAP_TX_MTU=69
|
|
CONFIG_BT_L2CAP_TX_BUF_COUNT=8
|
|
|
|
CONFIG_BT_MESH=y
|
|
CONFIG_BT_MESH_RELAY=y
|
|
CONFIG_BT_MESH_LOW_POWER=n
|
|
CONFIG_BT_MESH_FRIEND=n
|
|
CONFIG_BT_MESH_FRIEND_QUEUE_SIZE=16
|
|
CONFIG_BT_MESH_ADV_BUF_COUNT=20
|
|
CONFIG_BT_MESH_TX_SEG_MAX=6
|
|
|
|
CONFIG_BT_MESH_PB_GATT=y
|
|
CONFIG_BT_MESH_PB_ADV=y
|
|
CONFIG_BT_MESH_GATT_PROXY=y
|
|
CONFIG_BT_MESH_CFG_CLI=y
|
|
|
|
#CONFIG_BT_MESH_LPN_SCAN_LATENCY=30
|
|
#CONFIG_BT_MESH_LPN_RECV_DELAY=40
|
|
#CONFIG_BT_MESH_LPN_POLL_TIMEOUT=300
|
|
|
|
CONFIG_BT_MESH_SUBNET_COUNT=2
|
|
CONFIG_BT_MESH_APP_KEY_COUNT=2
|
|
CONFIG_BT_MESH_MODEL_KEY_COUNT=2
|
|
CONFIG_BT_MESH_MODEL_GROUP_COUNT=2
|
|
CONFIG_BT_MESH_LABEL_COUNT=3
|
|
|
|
#CONFIG_BT_MESH_IV_UPDATE_TEST=y
|
|
|
|
CONFIG_UART_CONSOLE=y
|
|
|
|
# this outputs btmon formatted data to the serial port
|
|
#CONFIG_BT_DEBUG_MONITOR=y
|
|
|
|
CONFIG_BT_DEBUG_LOG=y
|
|
|
|
CONFIG_BT_MESH_DEBUG=y
|
|
#CONFIG_BT_MESH_DEBUG_PROV=y
|
|
#CONFIG_BT_MESH_DEBUG_PROXY=y
|
|
#CONFIG_BT_MESH_DEBUG_BEACON=y
|
|
#CONFIG_BT_MESH_DEBUG_NET=y
|
|
#CONFIG_BT_MESH_DEBUG_TRANS=y
|
|
#CONFIG_BT_MESH_DEBUG_LOW_POWER=y
|
|
#CONFIG_BT_MESH_DEBUG_FRIEND=y
|
|
#CONFIG_BT_MESH_DEBUG_MODEL=y
|
|
#CONFIG_BT_MESH_DEBUG_ACCESS=y
|
|
#CONFIG_BT_MESH_DEBUG_CRYPTO=y
|
|
#CONFIG_BT_MESH_DEBUG_ADV=y
|
|
#CONFIG_BT_MESH_SELF_TEST=y
|
|
|
|
#CONFIG_BT_HCI_VS_EXT=n
|
|
|
|
#CONFIG_STACK_USAGE=y
|
|
|
|
CONFIG_BT_RX_STACK_SIZE=4096
|
|
|
|
#CONFIG_BT_DEBUG_HCI_DRIVER=y
|
|
#CONFIG_BT_DEBUG_HCI_CORE=y
|
|
#CONFIG_BT_DEBUG_GATT=y
|
|
#CONFIG_BT_DEBUG_CONN=y
|
|
|
|
CONFIG_BT_MAX_CONN=1
|
|
CONFIG_BT_CTLR_RX_BUFFERS=6
|
|
CONFIG_BT_CTLR_TX_BUFFERS=4
|
|
CONFIG_BT_HCI_CMD_COUNT=4
|
|
|
|
CONFIG_BT_ATT_PREPARE_COUNT=2
|
|
|
|
#CONFIG_NET_BUF_SIMPLE_LOG=y
|
|
#CONFIG_NET_BUF_LOG=y
|
|
#CONFIG_BT_CTLR_DEBUG_PINS=y
|