Some of the unittests had an incorrect project name in the
CMakeList.txt file
This is corrected here
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
When not using CONFIG_XIP (CONFIG_XIP=n)
the FLASH_0 mpu region needs to be removed,
otherwise it will have the default base
address = 0, which means that MPU will try
to configure the region with address 0.
We don't want this as in some situations
address 0 can be a restricted memory region
such as ROM code.
Signed-off-by: Alexandru Lastur <alexandru.lastur@nxp.com>
This reverts commit 7c90f1bca1.
Xen initialization maps enlighten page to Zephyr memory and also
initializes Xen event channels. It is used for communication between
Xen domains and based on interrupt connected to domain virtual GIC.
Moving event channel initialization to arch_kernel_init() make it call
irq_enable() when GIC is not initialized. Since GIC is initialized
on PRE_KERNEL_1 stage, this lead to fatal error during boot.
Revert these changes to make xenvm operable again.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
During migration to HWMv2 separate specific defconfig file was removed
for GICv3 version of virtual xenvm boards. It worked fine before
commit 0be0d2175b ("cmake: modules: extensions: Revert using common
board files") significantly changed build behavior, but did not return
previously removed file. This led to build/runtime issues, when some of
the Kconfig options were not selected.
Return GICv3 specific defconfig to board directory to fix configuration
problems.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
The new `host_config_variants` goal is to be able to test specific set
of configurations when building the Host without the need of having a
specific application for it.
The first test check that the Host build correctly with
`CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY` enabled.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
The functions `le_sc_oob_config_set`, `generate_dhkey` and
`display_passkey` in `smp.c` were only defined when
`CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY` was not defined. This created
issues at build time.
Remove the guard as the code calling those functions is not guarded
itself.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Fix possible race condition where SMP client might
release the network buffer before system worker queue
has processed it.
In smp_client uses shared resources like worker queue
linked list and network buffers without maintaining any
thread safety.
For unknown reasons, retry timeout handling is pushed
into system worker queue while the actual transmission
is handled from SMP work queue.
Fix the issue by using the same SMP work queue
for both delayable timeout handling as well as
transmission handling.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
In case TLS connect timed out during the handshake, errno was set to
EAGAIN which is unexpected and confusing. Fix this and set the errno
to ETIMEDOUT instead.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Remove danieldegrasse from NXP maintainers areas.
Substitute myself for the hal_nxp west project area.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add an area specifically for the MCUX shim USB drivers,
as this code is primarily maintained by a subset of the NXP Driver
maintainers. Move MarkWangChinese to this area.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add an area specifically for the NXP WIFI driver code,
since this code is maintained by a different set of people
than the generic NXP Driver maintainers.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Sets CONFIG_LOG_BACKEND_RTT_MESSAGE_SIZE=256 as some log
messages are longer than 128 (default) and may be truncated
with the existing configuration and implementation.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The compatible: "st,stm32h7-hsi-clock" has HSI clock divider
required which is set to 1, by default, delevering 64MHz
in the stm32h7.dtsi and stm32h7rs.dtsi
(As done for stm32h5 and other series)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This makes minichlink the default runner for the ch32v003evt.
This way, `west flash` "just works", as advertised in the README, rather
than having to manually set the runner to `minichlink` for it to work.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Use the broadcast sink callbacks to set the semaphores
rather than the stream callbacks, as the broadcast sink callbacks
are better for that as they are called when all streams are ready.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Use the broadcast source callbacks to set the semaphores
rather than the stream callbacks, as the broadcast source callbacks
are better for that as they are called when all streams are ready.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
These callbacks are trigger for changes that affect the entire
broadcast sink, such as the BIG synced and terminated events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
These callbacks are trigger for changes that affect the entire
broadcast source, such as the BIG started and terminated events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
These callbacks are trigger for changes that affect the entire
broadcast source, such as the BIG started and terminated events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add callbacks that is called for the entire BIG.
The BIG state is from an HCI perspective a single state change
that we previously only propagated as a state change for each
channel.
However it may be simpler for applications and higher layers
to use BIG changes to trigger their behavior.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This fixes an issue that occurred if deferred_work is queued by another
procedure before we run bt_conn_set_state(BT_CONN_DISCONNECTED).
bt_conn_set_state yields to the system work queue in bt_conn_tx_notify,
and then deferred_work runs and handles the disconnected callbacks.
bt_conn_set_state then enqueues another deferred_work which calls the
disconnected callbacks again and causes an assert. k_work_cancel_delayable
will clear queued deferred work when we call
bt_conn_set_state(BT_CONN_DISCONNECTED), guaranteeing that the disconnect
callbacks will only be called once.
Signed-off-by: Timothy Keys <timothy.keys@nordicsemi.no>
Add set the parameter `type` to value
`BT_SDP_DISCOVER_SERVICE_SEARCH_ATTR`.
Update the SDP discovery callback function by adding a third parameter
`const struct bt_sdp_discover_params *params`. Make it align with
`bt_sdp_discover_func_t`.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Since the function `bt_sdp_discover` has been updated, the caller of
function needs to be updated to avoid the building and functionality
fault.
Add set the parameter `type` to value
`BT_SDP_DISCOVER_SERVICE_SEARCH_ATTR`.
Update the SDP discovery callback function. Make it align with
`bt_sdp_discover_func_t`.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Extend the function `bt_sdp_discover` to support service search
transaction and service attribute transaction.
Improve the `session->rec_buf`. If the net buffer cannot be allocated
from the channel, disconnect the SDP session.
Set the `MaximumAttributeByteCount` of the request
`SDP_SERVICE_SEARCH_ATTR_REQ` with the tail room of `session->rec_buf`.
Set the `MaximumAttributeByteCount` of the request `SDP_SERVICE_ATTR_REQ`
with the tail room of `session->rec_buf`.
Set the `MaximumServiceRecordCount` of the request
`SDP_SERVICE_SEARCH_REQ` according to the tail room of
`session->rec_buf`.
Handle the response code `SDP_SERVICE_SEARCH_RSP`, and
`SDP_SERVICE_ATTR_RSP`.
Handle the error `SDP_ERROR_RSP`. Start the next SDP discovery if the
error received.
If there no more request, disconnect the session.
If the request cannot be sent, start the next SDP discovery.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
On RT1180/RT700, there is no gpr register on soc,
so change driver to get configuration register base
address from dts, instead of hard code.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
Deprecate mode which is using TIMER+(D)PPI for reliable byte counting.
Recently a new approach is added (CONFIG_UART_NRFX_UARTE_ENHANCED_RX)
which supports reliable byte counting without additional HW resource.
This mode is planned to be the only supported RX path mode.
Enhanced RX has slightly different behavior. There are no partial RX
packets (events with non-zero offset). There is UART_RX_BUF_RELEASED
after each UART_RX_RDY event.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Due to clock designed on RT1180 has some different with other platforms,
so add macro and handle the clock difference in mcux_ccm_get_subsys_rate.
TPM1 use Bus_Aon as clock root.
TPM3 use Bus_Wakeup as clock root.
Other instances have independent clock root.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
The PINCTRL option is selected now by the drivers which use it, so
it's possible to remove it from the board defconfig.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
- Add NULL checks for broadcast_source_stop
- Add NULL checks for broadcast_source_release
- Return -ESRCH if trying to stop ext_adv before creation
Signed-off-by: Alexander Svensen <alexander.svensen@nordicsemi.no>
The Smartbond SPI driver enables DMA acceleration by default. However
no DMA configuration is provided in the SPI node, resulting in run
time errors when the SPI interface is used. Instead, the application
should explicitly enable DMA acceleration and select the DMA channels
and priorities.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
