Default Voltage scaling range selection (range2)
doesn't allow to configure Max frequency
switch to range1 to match any frequency
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Default Voltage scaling range selection (range2)
doesn't allow to configure Max frequency
switch to range1 to match any frequency
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Fix macro used in g4 file to enable LSE clock.
Then, to avoid no-op configurations, generate an error
when MSI Hardware auto calibration is selected but LSE
clock is not enabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This PR addresses radio signal stength measurement during
and before PPP session. The PR provides provides facility
of readout for both +CSQ and +CESQ versions depending
upon the modems. This PR follows the idea of rssi readout
of PR#35496. Additionally, reliable Cell info update
is also ensured.
Signed-off-by: Tahir Akram <mtahirbutt@hotmail.com>
Add I2C bus initial support to Renesas R-Car SoC series.
Both I2C2 & I2C4 buses are supported on R-Car H3 board.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
This patch add support for I2C on the Renesas R-Car.
This I2C hardware block can be found on various Renesas R-Car
SoC series.
It allows to perfom read and write on I2C buses in an
interrupt based way on R-Car Gen3 H3ULCB board.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Third generation R-Car series products have up to
seven I2C bus interfaces conformant with the
Philips Semiconductors (now NXP Semiconductors) I2C bus
(Inter-IC bus) specification.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
As a first step towards being more forgiving on invalid inputs, allow
string-valued aliases properties that do not point to valid nodes when
the user requests permissiveness.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Modeled after dtc's --force option, the idea is this will try harder
and harder over time to produce an object despite malformed input.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
`_FOREACH_` macros do not allow the caller to pass additional arguments
to the `fn`. A series of `_VARGS` variants have been added that allow
the caller to pass arbitrary number of arguments to the `fn`:
```
DT_FOREACH_CHILD_VARGS
DT_FOREACH_CHILD_STATUS_OKAY_VARGS
DT_FOREACH_PROP_ELEM_VARGS
DT_INST_FOREACH_CHILD_VARGS
DT_INST_FOREACH_STATUS_OKAY_VARGS
DT_INST_FOREACH_PROP_ELEM_VARGS
```
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
Add power management support (runtime-idle and suspend-to-idle)
support for the NXP Kinetis KE1xf SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Enable the NXP Kinetis Low Power Timer (LPTMR) OS timer driver when
power management is enabled as the Arm SysTick timer cannot wake up the
KE1xF from deep sleep.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add NXP Kinetis Low Power Timer (LPTMR) OS timer driver shim. Since the
LPTMR does not support asynchronous changes to the timer period, only
non-tickless mode is supported.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Keep the Slow Internal Reference Clock (SIRC) running in low-power
mode.
This allows peripherals that needs to remain operative in low-power
mode to use the SIRC as clock source.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Do not enable the Arm SysTick driver by default. Instead, rely on the
default Kconfig settings for the Arm SysTick driver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Determine the default CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC from devicetree
when using the Arm SysTick hardware timer.
When the NXP KE1xF SoC series is using the Arm SysTick as hardware
timer, the cycles/second will always be equal to the CPU core clock
frequency.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The config/data casts are not strictly necessary. Furthermore, config
was being casted to non-const.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Use the recently introduced struct gpio_dt_spec to store GPIO
information and operate with them.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This is called in ISR context and timeout must be set
to K_NO_WAIT.
Reported-by: Pieter De Gendt <pieter.degendt@basalte.be>
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Adds a devicetree chosen node to the mimxrt1170_evk_cm7 board to link
Segger RTT and SystemView sections in DTCM by default. Enables the AHB
clock while the CM7 is sleeping to allow debug access to the TCM.
Note that automatic RTT control block detection may not search the DTCM
address region, therefore you may need to manually set the RTT control
block address or search range in the Segger host tools (SystemView or
RTT Viewer). For example,
$ JLinkRTTViewer -ra 0x20000000
Tested with:
- samples/subsys/shell/shell_module/
- samples/subsys/tracing/
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
`OT_LOG_LEVEL_NONE` has some uses within OpenThread but it is not
hanled in the Zephyr's platform implementation. This commit makes
use of those logs as `LOG_LEVEL_ERR` level.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
By default the hifive1 board doesn't enable the SPI controller that
the flash is on. As such this test will not build on that platform
due to lack of a missing SPI bus controller device.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable serial driver such that sensors commuicating via uart
can be added to this test(using the vnd,serial driver).
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds a serial dummy driver compatible to vnd,serial.
This is needed that devices can access the uart device in tests
like tests/drivers/build_all/... .
Add myself as codeowner to avoid complicance check failure.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Indicate which files have to be cleaned for each target. This feature is
only supported for CMake >= 3.15 and is ignored on older CMake versions.
Build will still succeed, but the `clean` target will not clean the
additional build files.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Simplify the devicetree generation. Most of the extra options are not
used, so they have been removed to make things easier to maintain.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactor the Kconfig target. Mostly formatting in this case. The Kconfig
script is also added as a dependency of the CMake configuration step, so
that if it is changed, the Kconfig generation step will be re-run.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactor the pdf build targets. The Sphinx latex build is now invoked by
the 'latex' target. The 'pdf' target can be used to build the resulting
LaTeX files.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactor HTML targets. The 'html' target is kept as is, 'sphinx-html'
equivalent is now 'html-nodeps'.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
