Add a property to the nxp,kinetis-gpio binding that related the GPIO
node to the pinmux PORT node.
For the kl25z we add the pinmux nodes as well since they didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Introduction of tachometer device nodes for the Microchip
MEC1501 SOC. In addition, dts bindings for are also introduced.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The max-value should just be an int and not an array. Change the type
to 'int' in the binding and fixup the driver to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pms7003 sensor driver to utilize device tree.
DTS would look something like the following for the pms7003:
uart {
pms7003: pms7003 {
status = "okay";
compatible = "plantower,pms7003";
label = "pms7003";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ak8975 sensor driver to utilize device tree.
This also supports the ak8975 embedded in a invensense MPU9150. In such
a case the device tree node should look something like, where the ak8975
is a child of the mpu9150.
mpu9150@68 {
compatible = "invensense,mpu9150";
reg = <0x68>;
label = "mpu9150";
#address-cells = <1>;
#size-cells = <0>;
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0xc>;
label = "ak8975";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This adds a simple binding for the Cadence Tensilica Xtensa LX4
CPU. File originally from the LX6 binding.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Convert to support devicetree.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Mark all CC2520 GPIOs as required
in binding.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Document and assign write-protect signal as active low, and use the
active-sensitive API to control it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update sample overlays. Add GPIO flags to configuration state.
Refactor to split out setup/handle/process phases. Switch to new API
replacing callback dis/enable with interrupt dis/enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Almost all drivers support 32 pins, though some support less.
Eventually this should be specified in every SOC binding, but until
then provide a default so GPIO drivers can be updated to use this.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since this was converted to the setup/handle/process idiom in master
the conversion is straightforward.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit updates the HMC5883L driver to use the new GPIO API.
Also add a note explicitly describing the active state of the DRDY
pin in the binding file.
Tested on frdm_k64f.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update sample overlay for missing chip select and to deconflict with
UART TXD. Add GPIO flags to configuration state. Replace callback
enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
