Compilation errors in ptp library when using C++ compiler.
First error is due to 'class' keyword being reserved in C++
and 'class' is used as a variable name in ptp library.
Second error is due to a flexible array member in a struct
is not placed at the end.
Signed-off-by: Tomas Choat <trc@ixys.no>
The asserts always fail because the condition is inverted.
This patch fixes the condition to verify the socket
is lower than PTP_SOCKET_CNT.
Signed-off-by: Tomas Choat <trc@ixys.no>
When the offset is larger than 1 second, the time
adjustment should still be allowed to be bidirectional.
Casting the offset to an unsigned value after the
subtraction will allow the adjustment to be bidirectional.
Signed-off-by: Tomas Choat <trc@ixys.no>
When sending follow up messages, the pre send function
does not insert the correct time stamp in the message.
Issue is fixed by calling the pre send timestamp function.
Signed-off-by: Tomas Choat <trc@ixys.no>
Use with statement to open stdout/stderr and resolve current warning
when running twister:
ResourceWarning: unclosed file....
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On the interrupt handling, one thread per driver instance is involved
into monitoring the semaphor, sends inside the gpio callback triggered
by the gpio interrupt. Each time, when the link parameters are change,
the DM8806 is generating the gpio interrupt. After getting semaphor,
the application callback function which was linked during initialization
process is called to get the new link parameters with standard API
calls
Signed-off-by: Robert Slawinski <robert.slawinski1@gmail.com>
New driver for Davicom DM8806 PHY. Driver is using standar mdio API
to manage the DM8806 switch controller. Register access needs the
PHY addres or switch address to be one of five possible values, since
DM8806 has built-in five PHY's. These values should be defined in the
application .dts file. One DM8806 ethernet port must corresponds with
one ethernet PHY node with two properties for ethernet port: one for
PHY address and one for switch address - <reg> for register access from
Internal PHY Register area and <reg-switch> for register access from
Switch Per-Port Registers area. Device tree example below:
example device-tree:
dm8806_phy: ethernet-phy@0 {
reg = <2>;
reg-switch = <8>;
compatible = "davicom,dm8806-phy";
status = "okay";
davicom,interface-type = "rmii";
reset-gpio = <&gpiod 2 GPIO_ACTIVE_LOW>;
interrupt-gpio = <&gpioc 1 GPIO_ACTIVE_HIGH>;
};
Signed-off-by: Robert Slawinski <robert.slawinski1@gmail.com>
Fixes the following warning:
<wrn> cbprintf_package: cbprintf_package_convert:
(unsigned) char * used for %p argument. It's recommended
to cast it to void * because it may cause misbehavior in
certain configurations. String:"%s: meta %p len %zu" argument:1
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
There is a unittest to verify that the distribute broadcast code procedure
is not called with the same peer twice. This test requires a minimum
of two connections, so we disable this test when only 1 connection
can be made
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
In case of unknown platforms in filters such as plaform_allow,
integration_plaforms or platform_exclude, report an error and exit.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update events to use uptime ticks, which is a monotonic clock which
in the same res as kernel ticks. This makes comparisons simple and
removes the complexity of dealing with wrapping counter values.
The wrapping is particularly problematic for events since this makes
it quite complex to track if an event has occured in the past, or
will occur in the future. This info is needed to know if an event
has actually been handled or not.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Move the previously singular env testsuite to be with the
other features that are part of the POSIX_SINGLE_PROCESS
Option Group.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add entropy support for these boards: ek_ra6m1, ek_ra6m2, ek_ra6m3
Signed-off-by: Danh Doan <danh.doan.ue@bp.renesas.com>
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Update hal_renesas to add SCE7 support for Renesas RA family
Signed-off-by: Danh Doan <danh.doan.ue@bp.renesas.com>
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
drivers/input/input_gpio_keys.c requires property "zephyr,code" must
be provides for gpio-keys, so add code property for imx93_evk A55
and M33 boards.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
A warning is giving for missing initalizer for field `exit_latency_us`
of `struct pm_state_info`. This adds the additional init fields.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The tests should only be allowed on supported platforms instead
of blanket enabling on architectures. There are platforms which
do multi level interrupts but cannot run the tests.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Adds a step direction binding that can be used with any stepper that
implements said control interface to cut down on boilerplate code.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Both tests set CONFIG_COMMON_LIBC_MALLOC_ARENA_SIZE=0 so extract
it to prj.conf. The tests require malloc arena size to be 0 to
run successful. By refactoring the config, it is now able to
with west build and still passing.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add the POLLPRI constant defined by POSIX and test for it.
Signed-off-by: Jakub Michalski <jmichalski@antmicro.com>
Signed-off-by: Maciej Sobkowski <msobkowski@antmicro.com>
Add the nfds_t type defined by POSIX and test for it.
Signed-off-by: Jakub Michalski <jmichalski@antmicro.com>
Signed-off-by: Maciej Sobkowski <msobkowski@antmicro.com>
For a long time now, it's been possible to call
`pthread_attr_init()` and have it just to The Right Thing (TM)
without having to statically assign a stack.
Remove the stale comment and commented-out code.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Correct "zephyr,sram" property under /chosen node to make board and samples
compatible with new SoC memory description.
Signed-off-by: Marcio Ribeiro <marcio.ribeiro@espressif.com>
Replaces hard-coded memory addresses and sizes with macros that retrieve
such values from the device tree.
Signed-off-by: Marcio Ribeiro <marcio.ribeiro@espressif.com>
Make sure smp_transport_clients list is only initialized once and
before any transports will try to register and add entries to this
list.
The smp_init() routine was called after smp_init_uart(), causing
the list to be emptied again after registration of the uart client
transport.
Signed-off-by: Bas van Loon <bas@arch-embedded.com>
There were code paths that could have lead to divide by zero given an
invalid scale setting for accel or gyro. In practice this should be an
invalid setup even before getting to these conversion functions. The
conversion functions now better show all valid values are accounted for
by using CODE_UNREACHABLE in the default case.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Now that the U5 HAL contains the dedicated LDO status function, use it
instead of reading the register directly.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
New HAL update changed the prototype of the check DMA flag functions.
H7 and U0 use a const parameter for these functions.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
This change adds @wearyzen as a collaborator to:
- ARM arch
- ARM Platforms
- West project: mbedtls
- West project: trusted-firmware-m
- West project: tf-m-tests
- West project: trusted-firmware-a
- West project: psa-arch-tests
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
On NXP RT1170 SOC, ADC ETC exists but it can not be enabled because
of dependency on HAS_MCUX_ADC_ETC.
Also, ADC ETC should only work with ADC together, there is no use
case to run it standalone.
Fixes:#81466
Signed-off-by: Raymond Lei <raymond.lei@nxp.com>
Some bluetooth host tests can be run on nrf5340bsim/nrf5340/cpunet.
This commit enables building and running these tests.
Signed-off-by: Artur Dobrynin <artur.dobrynin@nordicsemi.no>
Currently different test cases within the same folder are using largely the
same config files with only subtle variations. It is better instead to have
a base config file with general configuration, aided by overlay files for
specific cases.
Signed-off-by: Artur Dobrynin <artur.dobrynin@nordicsemi.no>
Bluetooth host bsim tests are compiled with shell scripts, but it is
possible to use twister, which supports compilation (but not running
at the moment). Compiling with twister requires fewer shell scripts,
provides cleaner interface and more flexible configuration.
Signed-off-by: Artur Dobrynin <artur.dobrynin@nordicsemi.no>
In the IOMUXC controller, the PDRV field uses 0b0 to set the pin drive
to high, and 0b1 to set the pin to normal drive. Fix the pinctrl_soc.h
definitions for the iMXRT11xx parts to use the correct setting for this
register, based on the documentation for the pin control binding
Note that for PDRV type pins, this commit effectively switches their
drive strength setting.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add tests for the new port / endpoint DT macros
Signed-off-by: Josuah Demangeon <me@josuah.net>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
