Abort any pending transmissions before entering configuration mode and
notify the senders.
Poll for mode change completion instead of assuming mode changes take
immediate effect. This is needed for successfully entering configuration
mode with recently aborted transmissions.
Fixes: #50545
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Given the recent change to the CAN controller can_send() API wrapper,
assume that a callback is always provided at the driver level.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Up until now, the Zephyr CAN controller drivers set a default bitrate (or
timing) specified via devicetree and start the CAN controller in their
respective driver initialization functions.
This is fine for CAN nodes using only one fixed bitrate, but if the bitrate
is set by the user (e.g. via a DIP-switch or other HMI which is very
common), the CAN driver will still initialise with the default
bitrate/timing at boot and use this until the application has determined
the requested bitrate/timing and set it using
can_set_bitrate()/can_set_timing().
During this period, the CAN node will potentially destroy valid CAN frames
on the CAN bus (which is using the soon-to-be-set-by-the-application
bitrate) by sending error frames. This causes interruptions to the ongoing
CAN bus traffic when a Zephyr-based CAN node connected to the bus is
(re-)booted.
Instead, require all configuration (setting bitrate, timing, or mode) to
take place when the CAN controller is stopped. This maps nicely to entering
"reset mode" (called "configuration mode" or "freeze mode" for some CAN
controller implementations) when stopping and exiting this mode when
starting the CAN controller.
Fixes: #45304
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the "z" prefix from the public CAN controller API types as this
makes them appear as internal APIs.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Reduce the number of TX buffers in use on the MCP2515 from 3 to 1 in
order to avoid CAN frame priority inversion.
The MCP2515 is unable to do internal TX frame arbitration based on the
CAN-ID of the frame. Priority must be set per TX buffer and the priority
cannot be rewritten unless the frame transmission is aborted.
Fixes: #26541
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add optional user data argument to can_set_state_change_callback() to
comply with Zephyr API design guidelines.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename a few CAN API functions for clarity and consistency with other
Zephyr RTOS APIs.
CAN_DEFINE_MSGQ() becomes CAN_MSGQ_DEFINE() to match K_MSGQ_DEFINE().
can_attach_isr() becomes can_add_rx_filter() since a filter callback
function is not an interrupt service routine (although it is called in
isr context). The word "attach" is replaced with "add" since filters are
added, not attached. This matches the terminology used is other Zephyr
APIs better.
can_detach() becomes can_remove_rx_filter() to pair with
can_add_rx_filter().
can_attach_msgq() becomes can_add_rx_filter_msgq() and documentation is
updated to mention its relationship with can_add_rx_filter().
can_register_state_change_isr() becomes can_set_state_change_callback()
since a state change callback function is not an interrupt service
routine (although it is called in isr context). The word "register" is
replaced with "set" since only one state change callback can be in
place.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
If the supplied sjw in the timing parameters is zero,
the sjw parameter should not be changed.
This fixes the uninitialized swj in can_set_bitrate.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
CAN_MCP2515_MAX_FILTER is not needed anymore and was probably just a
misunderstanding. Aligned it with the other CAN drivers.
This also was the last difference in the mcp2515 specific config for the
can sample, so that can be deleted as well.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
The previous API can't change the sampling-point and only allowed
bitrates that fit the time segments.
The new API allows for shifting the sampling-point and adjusts the
number of time quantum in a bit to all more possible bitrates.
The functions to calculate the timings are moved to the can_common file.
They can be used for all drivers.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Reduces SPI RX buffer read overhead by a byte and further reduces the
SPI use by automatically clearing the associated receive flag RXxIF.
Signed-off-by: Nick Ward <nix.ward@gmail.com>
This commit extends the CAN API with the following functions:
- can_get_state
- can_recover
- can_register_state_change_isr
This functions can be used to get the error-counters and the state
of the CAN controller. The recover function can be used to recover
from bus-off state when automatic recovery is disabled.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
move can.h to drivers/can.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The filenames of the can drivers were not consisten.
Changed them to can_<dev name>
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
