Checking that provided pclken->bus fits bus range in
clock_control_get_rate() is wrong as it could actually be a source
clock and hence not belong to this range.
Also, this kind of check is just not needed since this function should
not be used before call to clock_control_on() or clock_control_configure()
which do the required verification.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename and factorize clock source bindings accessors by moving them
in common header file stm32_clock_control and remove them from
include/dt-bindings/clock/stm32XY_clock.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Make the LSE driving capability configurable for the STM32 series.
Fixes#44737.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Instead of computing hclk freq use for flash latency setting after
setting the PLLs, do it right at the beginning of the function.
Indeed, first step of PLL configuration is to switch back sysclock
to HSI source (in case it was initially PLL).
In that case, flash latency is theoretically set in consistency with PLL
driver hclk. So we should "measure" hclk freq at that step rather than
once sysclock is back on HSI.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Take advantage of previous work to configure PLL and remove
usage of LL_PLL1_ConfigSystemClock_FOO utils functions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that fixed clocks are enabled in a single function, a
bunch of functions could now be removed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move fixed clocks initialization to a single function.
Benefit is they could now be enabled independently of the
main clock configuration based on dts status and then be
used by peripherals even is not part of the main clock tree.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Flash latency setting could be factorized in a single location,
rather than split in each clock setting function.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move prescaler settings to the clock_control_init function.
At this step they will be set up twice in PLL case, this will
be fixed in a next step.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add STM32_FOO_ENABLED and STM32_FOO_FREQ to STM32 fixed clocks:
HSI, HSE, MSI(S), CSI, LSI, LSE..
Replace STM32_LSE_CLOCK by STM32_LSE_FREQ and when possible
replace by new STM32_LSE_ENABLED when making sense.
Fix STM32_PLL3_FOO_ENABLE to STM32_PLL3_FOO_ENABLED
Additionally, add STM32_PLL_FOO_ENABLED definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Recent changes in this function made the code now compatible
with the use of LL API to perform this configuration.
Use it to simplify the driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Voltage scaling computation should be done in multiple cases.
Add a function that takes into account all cases.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In case of MSIS selected as system clock source it is necessary
to set Voltage scaling (VOS) when freqency is greater than 24MHz
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
When MSI trimming values where set to 0,
and MSIS is used as system core clock and MSI > 4 MHz,
it causes uart to fail.
There is no need to set thoses trimming values.
So keep the default reset value. (keep ST Factory calibration)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Because on stm32u5 MSIS is the default clock after reset,
changing MSIS range means immediate frequency change.
Thus it is important to do it after flash latency change
in case of higher new frequency.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Refactors all of the clock control drivers to use a shared driver class
initialization priority configuration,
CONFIG_CLOCK_CONTROL_INIT_PRIORITY, to allow configuring clock control
drivers separately from other devices. This is similar to other driver
classes like I2C and SPI.
Most drivers previously used CONFIG_KERNEL_INIT_PRIORITY_OBJECTS or
CONFIG_KERNEL_INIT_PRIORITY_DEVICE, therefore the default for this new
option is the lower of the two, which means earlier initialization.
The even lower defaults for STM32 and Arm Beetle are preserved by
SoC-family level overrides.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
When existing stop mode 1&2, VCO is set to range 4
and should be set back to range 1 to allow full speed
operations.
Rather than setting VCO at startup, set it inside clock
setting procedure so that it could done
in clock reset procedure when existing stop modes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This constraint on the AHB prescaler is removed.
The ahb-prescaler is allow from 1-512.
For stm32 common and stm32U5 devices.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enable PWR clock unconditionally for L4, L5 and U5
like it is done on other stm32 series
Fixes#37781
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Add clock_control driver to stm32u5 support.
For this series, now deprecated STM32 clock Kconfig symbols
are not added.
Due to a divergence in MSI clock definition, PLL1 use
instead of PLL and lack of sufficient abstraction abstraction
for these a dedicated file has been added.
This should be reshuffled:
- once a better abstraction is provided by LL API for these
- when some stm32 clock control driver rework will be done
after complete removal of Kconfig STM32 clock symbols.
Tested in MSI, HSI, PLL based HSI and PLL based MSI.
Not tested on HSE due to lack of compatible hardware.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
