This change brings in certain default configurations that are needed
for selection of random number generator, and to set tcp
configuration CONFIG_NET_TCP_ISN_RFC6528=n for nRF7002dk board.
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Add the PSA_WANT_XXX settings that might be needed for various crypto
algorithms and Keys in WIFI_NM_WPA_SUPPLICANT_CRYPTO_MBEDTLS_PSA
configuration setting.
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
In case the peer device has NO SDP record, the result is valid,
but the result->resp_buf is NULL, it would introduce a hardfault.
Therefore, also add a NULL pointer check for result->resp_buf.
Signed-off-by: Make Shi <make.shi@nxp.com>
Devicetree maintainers probably do not need to be pulled in for
dts/bindings/ folders that are found in various tests and samples
directories, the purpose of these lines was only for the top level
dts/bindings/ folder.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add @asm5878, @HoZel and @benothmn-st as collaborators on
"STM32 Wireless Platforms" and "West project: hal_stm32" where they
will take care of ble related libraries.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Add a new "STM32 Wireless platforms" area split from existing
"STM32 platforms".
STM32 Wireless covers STM32 BLE areas:
- STM32WB* based ST boards
- STM32WB* drivers/bluetooth/hci drivers
- STM32WB* soc/st/stm32
Additionally, the following domains are added to STM32 Wireless platforms:
- BlueNRG drivers/bluetooth/hci drivers
- shield x_nucleo_bnrg2a1, x_nucleo_idb05a1 and x_nucleo_wb05kn1
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Milliseconds are logged as is, without leading zeros. This means that
following log content is produced, which is not aligned by columns:
12:54:27.972:INFO:root: Test message
12:54:27.992:INFO:root: Test message
12:54:28.12:INFO:root: Test message
12:54:28.32:INFO:root: Test message
12:54:28.52:INFO:root: Test message
12:54:28.73:INFO:root: Test message
12:54:28.93:INFO:root: Test message
12:54:28.113:INFO:root: Test message
12:54:28.133:INFO:root: Test message
Change milliseconds logging to include leading zeroes. This allows to print
nicely aligned log messages:
12:54:27.972:INFO:root: Test message
12:54:27.992:INFO:root: Test message
12:54:28.012:INFO:root: Test message
12:54:28.032:INFO:root: Test message
12:54:28.052:INFO:root: Test message
12:54:28.073:INFO:root: Test message
12:54:28.093:INFO:root: Test message
12:54:28.113:INFO:root: Test message
12:54:28.133:INFO:root: Test message
Additionally it is much easier to configure programs simplifying
timestamped log browsing (like in logview-mode for Emacs), as it is more
standard and does not require custom regex matching.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
The ADC_ADS1X1X_TRIGGER macro was defined without an explicit value,
preventing ALERT/RDY pin configuration even when alert_rdy_gpios
were properly defined in devicetree. This occurred because
the IF_ENABLED macro specifically requires macros to be defined as 1,
not just defined empty.
Fixed this by explicitly defining ADC_ADS1X1X_TRIGGER as 1 when
alert_rdy_gpios properties are present in devicetree.
Signed-off-by: Benjamin Geiger <BenjaminGeiger1@gmail.com>
Some Python scripts need to access to the underlying OS, like
using redirections. These interactions go through TTY interface.
On MinGW, these interactions/interfaces are called 'winpty'.
=> use them when available (harmless on platform *NIX platforms)
Signed-off-by: Cedric Lescop <cedric.lescop@se.com>
Increase the maximum value of LOG_BUFFER_SIZE from 64 KB to 1 MB
to accommodate varying device requirements.
Signed-off-by: Jungo Lin <jungolin.tw@gmail.com>
This commit fixes a shared context between multiple instances of the
INA230 and INA236 driver. The issue is the naming of the instance data in
`INA230_DRIVER_INIT` macro when we have one instance of INA230 and one
of INA236 the name of the data variable will be `drv_data_0`. This
variable will then be passed to both instances.
Signed-off-by: Tomáš Juřena <jurenatomas@gmail.com>
uart_irq_update() should always be called in IRQ processing callback.
From API documentation:
"This function should be called the first thing in the ISR. Calling
uart_irq_rx_ready(), uart_irq_tx_ready(), uart_irq_tx_complete()
allowed only after this."
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add shield definition for the Mikroe ETH 3 Click.
ETH 3 Click is a compact add-on board that contains
LAN9250 SPI Ethernet Controller
Signed-off-by: Mario Paja <mariopaja@hotmail.com>
Add a driver for the Nintendo Nunchuk, accessed through the I2C bus.
This driver only supports the joystick and the buttons, not the
accelerometer.
Signed-off-by: Miguel Gazquez <miguel.gazquez@bootlin.com>
Add support for UDC on highspeed port on these boards:
- ek_ra8m1
- ek_ra8d1
- ek_ra6m5
- ek_ra6m3
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Do not allow enqueuing buffers on endpoints that were not enabled. Doing
so can lead to division by zero later on because the max packet size can
be 0 in disabled endpoint configuration.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
IAD must be before the interfaces it associates and therefore there is
no need for the class to be in charge of updating the bFirstInterface.
Update IAD in common initialization code and remove the updates from
classes.
This fixes UAC2 instances where the IAD bFirstInterface is not 0, e.g.
when HID was used together with UAC2.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Improve Simics support for `boards/intel/ish/intel_ish_5_8_0`
for better integration with the simulator.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Do hflipping at camera level to avoid using PxP which impacts camera
framerates on RT10xx. Moreover, on RT11xx, PxP is already reserved
for 90 CCW image rotation.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Add an option to mirror the video image horizontally. This helps
to avoid doing so at the post-processing step by using additional
HW such as PxP on i.MX RT platforms.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
It may be required to get information if NRF LF clock control calibration
is in progress. Some time sensitive operations could benefit from this
information.
The commit adds simple function that provides the information.
The function is nRF platform specific.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Pass additional args to test binary. Twister
passes it only for native_sim.
Fixes#82463
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
The reg address was not equal to the one in the node name, producing
a build warning.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
VPR address was obtained from the child instance, however, the child
nodes address is purely an index within the VPR node. The VPR address
needs to be obtained from the parent.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
These paths were not updated when we transitioned to hwmv2
which led to CI jobs not being triggered in some cases.
Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
These are currently failing CI and don't really have a maintainer or
someone who'd fully understand how they're supposed to work. Let's remove
them for now and longer term work on reintroducing them in a form that's
maintainable and understood by people actively developing the Bluetooth
host stack.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Make APP_CPU board name auto generated and remove the related config.
Remove the boards overlay and replace with a socs overlays.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Updates for AMP targets
- use common AMP Kconfig
- update APPCPU linker script
- place AMP common area in the reserved space
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Multiple AMP related updates:
- use common AMP Kconfig
- rework the APPCPU linker script
- use MCUboot image format for APPCPU image
- fix multi-processing startup code
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Update init function so APPCPU could not altere the clock setup.
Fix build in case if no inter-cpu module is selected.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
