Change the guard such that the iso_mtu and iso_pkts are
not guarded by BT_CONN as they should be available for
iso broadcast-only builds.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add the bt_acl_recv function that works similar to
bt_iso_recv but for ACL data only, simplying the
generic bt_conn_recv function.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Move the bt_conn_disconnect and conn_disconnect functions
to the ACL group.
Also adds a guard in the iso.c file for connected ISO.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Move the notify_le_phy_updated, notify_le_data_len_updated,
notify_le_param_updated, notify_remote_info,
notify_disconnected and notify_connected functions
to the ACL group.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Move the deferred_work callback function to the ACL group.
This also moves the static function conn_lookup_iso
which is only called form deferred_work.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Move the bt_conn_lookup_state_le, bt_conn_lookup_addr_le and
bt_conn_is_peer_addr_le functions to the ACL group.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Move the bt_conn_get_tx_power_level and
bt_conn_le_get_tx_power_level functions to the ACL group.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Start a group of functions guarded by CONFIG_BT_CONN
that are for connected-only functions. This is a
preparation step for allowing compilation and usage of
conn.c for ISO broadcast-only builds.
Moving all connected-only functionality into a single
group will also allow a possible move of all those
functions into an connected (ACL) only file.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
z_smp_init() is only available if CONFIG_SMP is defined,
smp_timer_init() also depends on two Kconfig parameters. Also make it
conditional in cavs_timer.c. Also clarify some SMP-related comments
there.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
log_backend_std_put had its own implementation for getting standard
flags which was identical to the one in log_backend_std_get_flags().
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds temperature platform used by the IEEE 802.15.4 Radio
Driver. The new platform requires an enabled temperature sensor.
The new hal_nordic revision updates the nRF 802.15.4 component.
Signed-off-by: Pawel Kwiek <pawel.kwiek@nordicsemi.no>
In file crc16_sw.c essential type of LHS operand (16 bit) is wider than
essential type of composite expression in RHS operand (8 bit).
In crc32c_sw.c and crc32_sw.c Essential type of LHS operand (32 bit) is
wider than essential type of composite expression in RHS operand (8 bit)
Found as a coding guideline violation (MISRA R10.7) by static
coding scanning tool.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Some recent updates to the bluetooth shell test cause build failures
in CI for platforms that don't have a uart that supports interrupts
(ie ip_k66f or xmc45_relax_kit).
As these tests are build-only a single platform is sufficient to get
coverage and utilize platform_allow to limit to just one board target
intead of integration_platforms. As this will limit to the single
platform for both PR based CI and nightly CI (integration_platforms
only is utilized for PR based CI, so we'd need other filtering for
the nightly CI and there isn't any value in building these tests
on more than the single platform so platform_allow makes the most
sense).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If "Cmake build failure" is detected test instance get status "error".
Despite this in final report this error is counted as failure. It can
be fix, by set proper results of each testcase in instance from None
to "BLOCK" after found Cmake error. After this fix, error is counted
properly in final report.
Fixes#37140
Signed-off-by: Piotr Golyzniak <piotr.golyzniak@nordicsemi.no>
SRAM partitioning for non-secure should be done via a reserved-memory
node and not fixed-partitions. fixed-partitions is meant for flash
style devices.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The irq will be enabled at the condition of start or repeat
start of I2C. If timeout occurs without being wake up during
suspend(ex: interrupt is not fired), the irq should be
disabled immediately.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Includes a table to display compatibility between debug probes and host
tools.
Moves the J-Link External Debug Probe section up for consistency with
host tools listings and to clarify separation between sections.
Reformats Flash and debug with ST-Link section with tabs for different
host tool options for clarity and readability.
Signed-off-by: Julia Hathaway <julia.hathaway@nxp.com>
Reformats the three sections on flash configuration for devices with
different bootloader compatibility into tabs to streamline instructions
Signed-off-by: Julia Hathaway <julia.hathaway@nxp.com>
Change removes logs and assertions from default configuration.
They can be optionally enabled with debug_overlay.conf.
CONFIG_BT_BUF_CMD_TX_COUNT is increased to avoid dropping
HCI commands.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
