The HCI spec defines the BIS index range as starting from
index 0x01. We had previously implemented it such that it
starts from 0x00, and then simply adding 1 to the index
when sending over HCI. However, this may cause issue with
other HCI, or other SIG defined specification, commands
and events, and thus it is probably simpler if we just
use the HCI defined range.
This commit disallows BIT(0) (representing the BIS
index 0x00) to be set, and removes the addition
of 1 when sending over HCI.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Position over LTE (PoLTE) can be used to locate a device as
an alternative to GNSS.
Increase RX thread stack size for PoLTE processing.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Allow application control for starting modem driver.
This allows network attach to be randomized.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
When run by a makefile twister might fail to decode the text results of
commands, based upon the environment settings of the system. With this
change escape characters are removed before the string is passed to the
json decoder.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Remove littlefs dependency as FS backend works with any file system as
long as it is (manually or automatically) mounted.
Fixes#36851
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
Fix null pointer deferencing in Periodic Synchronization
when ULL execution context could not assign an auxiliary
context when in LLL scheduling to receive chain PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix null pointer dereferencing in Extended Scanning when
there are more peer devices than the allocated auxiliary
contexts.
When LLL scheduling does not get an auxiliary context
assigned in the ULL execution context, then further chain
reception is aborted, access to `lll->lll_aux` which is
NULL causes null pointer dereferencing in
`ull_scan_aux_release`.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When Extended Initiating a connection, release auxiliary
context memory referenced by the lll_aux pointer.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Update Periodic Advertising Synchronization's drift
compensation to save radio ready and address capture on
AUX_SYNC_IND reception, restore and apply at the end of
reception of all AUX_CHAIN_IND PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Instead of checking `if (iso == NULL)` it simply checked
`if (iso)` which is the opposite of what it should have done.
This completely blocks iso from connecting channels.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
So fare flash simulator had been forced to use the statistic
subsystem.
This patch introduces CONFIG_FLASH_SIMULATOR_STATS which allow to select
whether the statistic is involved in flash_simulator operations.
This patch allows to reduce flash footprint when the statistic is
not required.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
For getting the address of the RAM region in the application we need to
extend the api for the flash_simulator.
This path introduce flash_simulator_get_memory() call which allow to
do so.
Signed-off-by: Sigvart Hovland <sigvart.m@gmail.com>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
cdc_acm_irq_tx_ready was not checking if its interrupt was enabled.
This causes spurious tx irq handler calls.
Signed-off-by: Eric Johnson <eric@liveathos.com>
Fixes the issue where uart_sam0_irq_tx_ready would return true if
the INTFLAG was set even though the INTSET bit for the given
interrupt was not enabled yet through uart_sam0_irq_tx_enable.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
Create a board overlay file in the application directory to add
pwm-led0 entry over default device tree. Also, include instruction
in the README file that connection of external LED at pin PA8 is
required for the demo to work.
Signed-off-by: Waqas Mazhar <waqas.mazhar@planetinnovation.com.au>
Node names are subject to the rules in table 2.1 of the devicetree
specification v0.3, while properties are subject to rules in table
2.2. These rules mean that some property names are invalid node names.
However, the same regular expression is being used to validate the
names of nodes and properties in dtlib. This leads to invalid node
names being allowed to pass. Fix this issue by moving the node name
handling code to the Node constructor and checking against the
characters in table 2.1.
The test cases claim that the existing behavior matches dtc. I can't
reproduce that. I get errors when I use invalid characters (like "?")
in a node name. For example:
foo.dts:3.8-11: ERROR (node_name_chars): /node?: Bad character '?' in
node name
Try to make the dtlib error message reminiscent of that.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is unused since the very beginning of the module's introduction.
It looks like it was abandoned in favor of the approach where each
token can have only one capturing group.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
For low power operation, set the IP connection reconfig
flag when receiving a startup report.
This will ensure the GPRS connection is reconfigured
before any socket operations take place.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
We get build issues due to the removal of the Kconfig symbol
CONFIG_UART_SHELL_ON_DEV_NAME on platforms that didn't have a uart
set as we'd get a default value for those platforms. Update the
Kconfig logic to only enable SHELL_BACKEND_SERIAL if we have
zephyr,shell-uart specified in the devicetree to address the issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allow the driver to run if a SIM card is not present.
This allows public HL7800 APIs like firmware updates
to be used even if no network is available.
Remove duplicate query ICCID command.
Signed-off-by: Andrew Hedin <andrew.hedin@lairdconnect.com>
This changes "__nocache K_HEAP_DEFINE()" to use the new
K_HEAP_DEFINE_NOCACHE() macro. This fixes a build error
as K_HEAP_DEFINE() is specifying its own linker section
so that it is no longer possible to specify another
linker section.
Fixes#38108
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows a kheap to be defined in the uncached memory.
For example, this can be used for DMA transfer buffers.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
System heap buffer was moved from dram0_0_seg to dram0_1_seg.
This commit fixes system heap buffer placement.
Signed-off-by: Shubham Kulkarni <shubham.kulkarni@espressif.com>
Timeout cancel should only be done for connections established in
peripheral role.
Enhanced connection complete event could still be delivered without
extended advertising support (i.e no advertising set terminated event)
so this handling should be moved to the common conn complete function.
Fixes#37467
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
SMP support on cAVS is implemented by using uncached addresses for all
writable data sections except for stack, i.e. for .data, .bss and
some other specialised ones. So far that has been implemented for
cAVS 1.5/1.8. This patch does the same for cAVS 2.0.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Removes all the dead ternary expressions in the mesh bluetooth tester.
Fixes#37983.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
PR #35774 introduced a uuid field in the bt_mesh_cfg_mod_pub structure.
The shell does not initialize this pointer before passing it to the
access layer. Add a line to initialize this pointer.
Fixes#38016.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
param can never be NULL here, so the check is redundant. Coverity is
complaining because param is accessed before the NULL check.
Fixes#37949.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
param can never be NULL, so this check is redundant. Coverity complains
about this, as the param variable is accessed before the check, which
would be wrong if param could be NULL.
Fixes#37948.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
When Extended Scan Response data of length zero is set, the
Scan Response do not have the Common Extended Payload Format
and hence no ADI field. Fix uninitialized pointer to Scan
Response Data's ADI to avoid copy of ADI from primary
channel PDU.
Fixes#38015.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
