Global data and device setting can be messed up by concurrent
API calls. This change is to serialize the access.
Jira: ZEP-454
Change-Id: I520722aecab7db443d053fd45498a22e165889de
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This currently only supports outgoing messages without interrupts.
Change-Id: I635562f47106eb6cdc7104a8160e431bebea25dc
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In order to change the baudrate the DLAB bit of the LCR register has to
be set to 1 (This bit is used to enable reading and writing of the
divisor latch register). This bit must be cleared after the baudrate
setup in order to access other registers.
The set_baud_rate function correctly sets the DLAB bit of the LCR reg but
never clears it. Therefore the ns16550 doesn't properly work any more
after updating the initial baud rate.
In order to fix this issue the LCR reg has to be temporary saved
(because it contains other important settings). After switching to a new
baud rate the LCR reg value has to be restored.
Change-Id: Ied4db683cbf40ba3125e747552968ddf1a66e2be
Signed-off-by: Jeremie GARCIA <jeremie.garcia@intel.com>
Signed-off-by: Sebastien GRIFFOUL <sebastien.griffoul@intel.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On current Curie-based boards UART 0 is wired to the nRF51 BLE
controller and requires HW flow control to be enabled in order to
function. This patch restores the same behavior that was present
before the "qmsi: uart: use built-in qmsi driver" patch.
Change-Id: If7ea347f5ab8b460f39123dcc0d75d711a5a1c2a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use SOC_SERIES_* for naming SoCs with similar features and architectures
with the goal of code reuse. The Series in the config variable should avoid
name collisions and clearly denote the relationships within an SoC family.
Change-Id: I7a98542f96b5d5dc3acc23782c4d45f98cceb599
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use CONFIG_SOC_FAMILY for the top level SoC family. A family
will have different SoCs or different SoC series with multiple
SoCs.
Adding the Family string to the config variable to avoid confusion
between actual SoCs and families and to prevent name collisions.
Change-Id: Ic99a2c1df7850dee3a45641027af82464dd6fadb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Note that the failure case can only be reached when PCI is enabled.
Otherwise, the if-block is always false, which reduces code size
for non-PCI platforms.
Change-Id: Ib98b78a75cc2a5f124e67f32f2bf82960a963aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The IRQ triggering condition should be specified by SoC as it is
a decision for hardware design. This should not be configurable
in kconfig.
The default is to be triggered on rising edge, just as the same
old kconfig did.
Change-Id: If59d88a30711eb8e03d9cc4f409055cefe1995c5
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Moves those kconfig options which should be declared in
SoC or board header files instead. These are the one
that are tied to SoC or board and there is no need
for them to be configurable in kconfig.
Change-Id: I243d634f1a4a11dc8dc3530d95f93371015492b7
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The UART port base address, IRQ line and clock frequency are static
per SoC, so there is no need to make them configurable in Kconfig.
Change-Id: Ia252958d205e0100d1b92e2a12d4c22411bc94b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The UART port base address, IRQ line and clock frequency are static
per SoC, so there is no need to make them configurable in Kconfig.
Change-Id: I79b142414143bc5ef585d3136a00375233de1723
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch fixes the QMSI UART shim driver so we are able to use it in
Quark D2000 based platforms. Differently from Quark SE, the peripheral
clock gate bit (CLK_PERIPH_CLK) is not enabled by default in Quark
D2000. We have to explicitly set this bit in order to properly initialize
the device.
Since this drivers is now properly working on Quark D2000, this patch
also sets the QMSI driver default options in arch/x86/soc/quark_d2000/
Kconfig.
Change-Id: I817b7703554be162ac628dcd8d3d07512b9eb3f5
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The patch extends STM32 serial port driver with support for IRQ API of
the common UART port driver API.
Change-Id: If105e8528ea4ed4181cc4af0c97c24aa874e69e0
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add driver for U(S)ART ports on STM32 MCUs. The driver implements basic
RX/TX functionality. Data transmission is implemented using polling. The
driver configures the port to use 8bit data transmission, 1 stop bit, no
parity control.
The driver exposes a public uart driver API and registers a single UART
device 'UART_0'. The device binds to USART1 peripheral and performs
required pinmux and clock control configuration. The device can be
initialized at the PRIMARY level, with default device priority.
The driver has been verified to work with a sample Hello World
application on a STM32F103 series MCU.
Change-Id: Iae103fcd8d2fb0a6c173cf141a68e17791255aab
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
() Adds some comment to divide config options for easier
visual navigation.
() Put config under submenus to make all driver options
consistent with each other.
Change-Id: Ia219c5283e4fa394adf8b0ac03577a0fd033ec1c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch replaces all occurences of the macro DEV_NO_SUPPORT by
-ENODEV at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/ when applicable.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I03007527367b03e6fd72a85004b7d3b81046a6a6
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch replaces all occurences of the macro DEV_INVALID_CONF by
-EINVAL at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/ when applicable.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: Idae0d5af8dd780416977c9261a5fb6188c3aab64
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch replaces all occurences of the macro DEV_INVALID_OP by
-ENOTSUP at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/ when applicable.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I46aec3c65963018c479b01602e4a3eec8650eaff
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch replaces all occurences of the macro DEV_OK by the actual
value 0 at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I69980ecb9755f2fb026de5668ae9c21a4ae62d1e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch extends the UART QMSI driver so it supports the IRQ APIs from
include/uart.h. The IRQ APIs are enabled by the 'CONFIG_UART_INTERRUPT_
DRIVEN' option.
Differently from others APIs such as I2C and SPI, the UART API is very
low level. For that reason, the IRQ facilities (e.g. irq based transfers)
from the QMSI driver are not useful to the shim driver at the moment. In
order to implement the IRQ APIs we rely on UART registers defined by QMSI.
QMSI UART header is missing some macro definitions from IRR register so
we define them in the shim driver.
Since the IRQ trigger condition is not configurable in the QMSI shim
driver, this patch also changes drivers/serial/Kconfig so the "UART
IRQ Trigger Condition" choice doesn't appear on the menu if the QMSI
driver is selected.
Change-Id: Idf9a0f6a47af2a550a31f474d721068dca989713
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch extends the UART QMSI driver so it supports line control and
driver command APIs.
The line control function supports the baud rate option only (LINE_CTRL_
BAUD_RATE) and, at the moment, the QMSI driver doesn't have any custom
command.
Change-Id: Icc10cb39b4077ed4ccfefb1f0feecec75b79d67c
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch extends the UART QMSI driver so it supports different baud
rate configurations. The baud rate is set per UART controller via
menuconfig. The default baud rate is 115200.
Change-Id: Iad736d72bd309b8a33ab5d538251fce374e89fd2
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch introduces the QMSI UART driver which is simply a shim driver
based on UART driver provided by QMSI BSP.
This initial version implements only the mandatory APIs 'poll_in',
'poll_out' and 'err_check' which are required by trivial sample apps and
by output functionality from the console driver. The remaining APIs will
be implemented by up coming patches. The driver supports only 115200 baud
rate at the moment.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_SERIAL=y
CONFIG_UART_QMSI=y
This driver has been tested with Quark SE Devboard so this patch also
adds its platform-specific default configuration options to 'arch/x86/
soc/quark_se/Kconfig'.
Change-Id: Ibde1825d4b0349a376a8e7d91cc9de306946b62f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Not all of the variables defined in the driver data structure are
required. So put some #ifdef around them.
Change-Id: I08a0c02d9e5c6885d9b4d6237446bdb9b98f3bfa
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Looking at all structs as to where we can pack them a little better, and
calling out the padding/stride at the end for future expansion.
Change-Id: I4a651092e950dd3d915af9fa0ee0d7d59803e58f
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds extern "C" { } blocks to header files so that they can be
safely used by C++ source files.
Change-Id: Ia4db0c36a5dac5d3de351184a297d2af0df64532
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This adds driver for the UART controller on Atmel SAM3X8E.
This UART controller only has two wires for RX and TX, and
does not have flow control (e.g. CTS, RTS) or FIFO.
Currently, the driver does not support any interrupt driven
operations.
Change-Id: I63720bccfb70a89888353b8ee3dfc4b80793dc01
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This API is not being used for anything, the interrupts for UART
drivers are all being configured statically. Saves code space as
gc-sections can't tell that these APIs are unused.
Some instances where IRQ/priority information was being saved in
data structures and never used fixed.
Change-Id: If56b4fdc251b80be9094ffcbac6f61e265ac2ffd
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This implements the newly introduced APIs to manipulate line controls
for UART.
This also implements the driver command API as setting baud rate
may require setting the DLF.
Change-Id: I80634aa3fbd4a3223c46edb61417123e36f439dd
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds 2 new APIs to the serial/uart drivers:
() One is to control the serial line, such as RTS and CTS.
() Another one is to allow driver to expose hardware specific functions
to apps. This is needed as some hardware may have extra registers to
set for baud rate.
To keep the code size small, these features are disabled by default.
Change-Id: I15c000ce68a0a490dcfd3493b2fe9bc51fa974fa
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This moves the baud rate and options fields out of the UART driver
config struct and into the driver data struct. This will allow
changing baud rate and options at runtime in the future.
Change-Id: I62ddea2f95e634f2d60eeb9537f960799fc9301f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
