For historical reasons, inversion mode is enabled by default in the
current implementation. This commit introduces an `inversion-off`
boolean DTS property, allowing it to be disabled if necessary.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Adds support for the PGOOD pin. This pin is asserted by the
regulator when converter startup has completed and the output
is stable. If the PGOOD pin is not used, the PGOOD state is
check via the PGOOD_PIN_STS bit.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Deprecate the use of location_* properties in the i2c_gecko driver
and migrate to the pinctrl api for enhanced maintainability and
compliance with current standards.
Signed-off-by: Arunmani Alagarsamy <arunmani.a@capgemini.com>
This property will allow PWM driver allocate data buffer
in appropriate memory region.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Driver already handles the case when 'reset-gpios' is not provided, so
remove 'required: true' from bindings to allow boards / shields definition
without reset signal being connected to any Zephyr controlled GPIO.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
This commit refactors the Intel SSP DAI driver to support dynamic
management of SSP IP. This change additionally separates the management
of the DAI part from the management part of the SSP IP.
Key changes:
- Add new static functions to manage SSP IP power.
- Update the DAI SSP configuration functions to use the new management
approach.
- Update device tree bindings and instances to reflect the new SSP IP
management mechanism.
Signed-off-by: Damian Nikodem <damian.nikodem@intel.com>
The commit restricts erase-value to either 0xff or 0x00.
On program-erase type devices writes can only change from
erase value of bit to opposite, ease usually consists of two
operations which is programming the opposite value to every bit
of erase range and then turning back all bits to the "erase-value";
above makes it impossible to have erase value of device to be other
than 0xff or 0x00.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This implements basic driver to utilize the I3C IP block
on NPCX.
1. I3C mode: Main controller mode only.
2. Transfer: Support SDR only.
3. IBI: Support Hot-Join, IBI(MDB).
Controller request is not supported.
4. Support 3 I3C modules:
I3C1(3.3V), I3C2(1.8V, espi mode), (I3C3 1.8V or 3.3V)
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
add gpio_intel driver with acpi based resource enumeration support.
Also updated test cases overlay with new dts entires.
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
FTM internal counter can be clocked by one of three clock sources
independent of the module bus clock. This patch introduces a DT property
to perform the clock selection from DT.
DT sources are updated to keep the current clock selection for all boards,
with exception of ucans32k1sic board which is migrated to use system
clock by default, as this seems to be a better choice for most cases.
Some PWM LED samples require slower clock so overlays are added for
those cases.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add support for half-duplex (3-wire) SPI operation using the Raspberry
Pi Pico PIO. To allow control of the size of the driver, including
half-duplex support is optional, under the control of Kconfig options.
The original PIO source code is also included as a reference.
Corrected 3-wire tx/rx counts.
Enable half-duplex code based on DTS configuration
Replace runtime checks with static BUILD_ASSERT()
Remove too-fussy Kconfig options
Removed PIO source per review request
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
The MAC address macros are ridiculous in this driver.
Rewrite to be simpler and use eth.h common function.
Also, clarify the mac address generation on the DT overlays.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Adds a DAC driver for Texas Instruments DACx0501 family of devices
Signed-off-by: Eran Gal <erang@google.com>
Co-authored-by: Martin Jäger <17674105+martinjaeger@users.noreply.github.com>
Enable MIPI mode to be set via devicetree, for displays that support
multiple MIPI DBI modes. This commit also adds new helpers for displays
that allow drivers to initialize the entire MIPI DBI configuration
structure from devicetree
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Nuvoton NPCX chips have reset registers which allow to reset the
peripheral hardware modules. This commit adds the support by
implementing the reset driver. Note that only the reset_line_toggle API
is supported because of the nature of the reset controller's design.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Currently, all devices are initialized at boot time (following their
level and priority order). This patch introduces deferred
initialization: by setting the property `zephyr,deferred-init` on a
device on the devicetree, Zephyr will not initialized the device.
To initialize such devices, one has to call `device_init()`.
Deferred initialization is done by grouping all deferred devices on a
different ELF section. In this way, there's no need to consume more
memory to keep track of deferred devices. When `device_init()` is
called, Zephyr will scan the deferred devices section and call the
initialization function for the matching device. As this scanning is
done only during deferred device initialization, its cost should be
bearable.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
CSS was deprecated from the mcu-sdk. Removing driver from lpc55s36
to clear build error.
This is a temporary patch to remove the build error.
Fixes#69961
Signed-off-by: David Leach <david.leach@nxp.com>
Implement a sensor for the output diagnostics of the power train
switch TLE9104.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This commit enables pinctrl on i.MX8ULP. This includes:
1) Adding `pinctrl_soc.h` header file.
2) Adding DTS node for IOMUXC1, which is one of the
IPs responsible for managing the 8ULP pads.
3) Adding .dtsi with pin definitions. For now, only
the LPUART7 pads are added to this file because this
is going to be the only consummer for now.
4) Modifying the `pinctrl_imx.c` driver to work for 8ULP.
5) Enabling the `CONFIG_HAS_MCUX_IOMUXC`, which is a
dependency of `CONFIG_PINCTRL_IMX`.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add binding for sitronix ST7796s, a MIPI DBI display controller
supporting up to 320x480 displays at 18 BPP
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The SparkFun Pro Micro header pins are numbered D1, D0, GND, ... from top
left whereas the SparkFun Pro Micro RP2040 and the Adafruit KB2040 boards
are using gpio 0, 1, GND, ... , so the pro_micro: connector gpio-map of
these boards should reflect that.
Graphical Datasheet for SparkFun Pro Micro RP2040:
https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf
Graphical Datasheet for SparkFun Pro Micro:
https://cdn.sparkfun.com/assets/f/d/8/0/d/ProMicro16MHzv2.pdf
Pinout of the Adafruit KB2040:
https://learn.adafruit.com/assets/106984
Please note that the KB2040 uses CircuitPython pin labels D0, D1 which does
not seemt correspond to the Arduino labels D0 and D1 used by the Pro Micro.
Signed-off-by: Daniel Irekvist <ulmanyar@gmail.com>
Add devicetree binding for NXP LCDIC. This controller is capable of
driving displays in 8080 or SPI 3/4 wire mode, and optionally swapping
endianness of display data as it sends it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The initial version of an input driver for Cirque Pinnacle ASIC supports:
* Setting sensitivity
* Choosing between relative and absolute modes
* Relative mode
* Primary tap
* Swapping X and Y
* Absolute mode
* Setting number of idle packets
* Clipping coordinates outside of active range
* Scaling coordinates
* Inverting X and Y coordinates
Signed-off-by: Ilia Kharin <akscram@gmail.com>
For now DSI settings are hard-coded for the specific
LCD module used on the STM32H747I Discovery board
Signed-off-by: Erik Andersson <erian747@gmail.com>
To support the NT35510 display, some additional
options needs to be configurable in the STM32
DSI peripheral
Signed-off-by: Erik Andersson <erian747@gmail.com>
Add support for performing pinctrl operations. For now,
the only supported operation is applying the pinctrl default
state. Pinctrl is left optional to allow for scenarios in which
this is not required (e.g: AMP system in which another
OS configures the pinctrl).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add a property to select the push-pull GPIO output type to drive the
I2C recovery. The default is open-drain.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Based on the iis2dlpc driver, with some significant differences in
interrupt handling.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
