The gpio-emul driver does not actually require any reg property,
since it is not in the physical memory map of any device. So
let's remove that property from the bindings.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Remove all CAN controller "bus-speed" and "bus-speed-data"
properties. These all use the default bitrates set via Kconfig.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Set the default initial bitrates globally via Kconfig. The initial bitrates
can still be overridden using the "bus-speed" and "bus-speed-data"
devicetree properties.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove nxp_ground_select property.
Delete the use of NXP vref peripheral CSR register REFL_GRL_SEL bit.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
PHYTEC has multiple offices in different locations like
the US, France, India and China. The headquarter is located in
Germany. Since now 50% of the PHYTEC boards are from the US
office, we should drop 'Messtechnik GmbH', which is the offical
title of the German office, and keep the name more general.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The new bindings for the stm32 xspi is for new stm32 devices with
XSPI peripherals like the stm32h5 serie. This is close to the octo-spi.
Adapt the flash controller constants to the XSPI model especially.
This is done through a new xspi.h definition file.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add driver, together with the corresponding dts binding and node in
the nRF54H20 SoC definiton, for the nRF temperature sensor that cannot
be accessed directly but only through nRF Services (nrfs) layer.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit makes the devicetrees of the targets that are based on the QEMU
`virt` machine more consistent with the rest of the RISC-V targets in
Zephyr by:
* adding the `riscv,isa` property
* adding a compatible string which uniquely identifies the `virt` core
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The CSI can connect to either a camera sensor (as on i.MX RT10xx) or
a MIPI CSI-2 receiver (as on i.MX RT11xx). To be generic, change the
naming from sensor to source.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Add initial HID device support. Unlike the existing HID implementation,
the new implementation uses a devicetree to instantiate a HID device.
To the user, the HID device appears as a normal Zephyr RTOS device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The clk, dqs and ncs pins can be remapped between OSPI instances, but the
driver doesn't support it, yet. Therefore replace hard coded numbers to
device tree optional properties.
Signed-off-by: Samuel Kleiser <s.kleiser@vega.com>
Allow configuration of the system pll on the iMXRT10xx series parts, via
a fractional pll node under the CCM module.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adding required flag to the current-speed as without this driver
does not compile.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Gives number of the Extended Interrupts and Event Controller (EXTI)
interrupt line connected to the RTC Alarm event.
Used on all series, except WBAX & U5X, where RTC Alarm interrupt is
routed directly to Nested Vectored Interrupt Controller (NVIC) and to
Power Control (PWR) wake-up pins.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
This change allows to use DTR line driven from external serial port
that when active (low) will prevent UART device from going to sleep.
It will also wake up platform when DTR line becomes active.
DTR line is often activated in serial port connected to host computer
when operating system opens serial device like COMx for Windows
or /dev/ttyACMx /dev/ttyUSBx for Linux based systems.
DTR line (specified in device tree) will be used by WAKEUP and PDC
controllers (via GPIO driver) to handle DTR line changes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This change allows to wake up UART from sleep mode when
low level on inactive UART is detected during platform sleep.
Timeout can be specified for each UART separately in device tree.
If one of the UARTs is selected as console sleep timeout is taken
from Kconfig same way other platform configure same functionality
using CONFIG_UART_CONSOLE_INPUT_EXPIRED_TIMEOUT
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
If no HSFLL needs trimming, then `trim_hsfll()` should be compiled out.
This makes it easier to reuse the rest of `soc.c` out of tree.
Furthermore, some HSFLL instances can be trimmed before booting Zephyr,
so the FICR client properties in the DT binding should not be required.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
The emulated GNSS driver behaves like a GNSS, implementing
device pm and the GNSS APIs, using only kernel features (
zephyr work queue and uptime) making it buildable on all
zephyr targets.
The purpose of this device driver is to tailor and validate
the gnss api test suite.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Add mfd_adp5585 and gpio_adp5585 driver. This driver enables ADP5585
as an GPIO expander.
This chip is used as an GPIO expander on i.MX93 EVK. GPIO pinctrl,
read/write and interrupt is supported.
Note that ADP5585 has 2 GPIO banks with 5 pins each. The driver combines
two group into a 16-bit port. Index 0~4 correspond to R0~R4 lines, index
8~12 correspond to C0~C4 lines. Index 5~7 is reserved unavailable.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
The counter driver needs to know what is the maximum
counting frequency of each timer peripheral.
Let's add it to its DT.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add binding for adi SDP-120 connector and header file
with marcos to map signals using signal names.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Add driver for IS66WVQ8M4 PSRAM, using the MCUX FlexSPI interface to
write data to the PSRAM device.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Some instances of the FlexSPI IP support a different clock source being
used for port B of the FlexSPI instance. Add a devicetree property and
driver support to enable configuring this property of the hardware.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added EXMIF peripheral DTS description and bindings.
The peripheral operates as an SPI device.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Add support for similar adin1100 phy, boath are 10Base-T1L,
only difference is that adin1100 connects through r/mii.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
MDIO is part of the ETH IP, but some phy chip may need a
specific phy driver to set up certain vendor registers enabling
particular features.
Add support for stm32 mdio access.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Add Sequans GM02S modem binding using the sqn vendor prefix.
The modem has an active low reset signal.
Signed-off-by: Thibo Verheyde <thibo@dptechnics.com>
Intial driver adding intial script to receive only GGA, RMC and GSV
NMEA messages, configuring fix rate, setting enabled system and adding
power management with the module on-off pin.
Signed-off-by: Jeronimo Agullo <jeronimoagullo97@gmail.com>
Spell checking tools do not recognize "iff", replace with "if and only if".
See https://en.wikipedia.org/wiki/If_and_only_if
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Convert the ht16k33 to use the input subsystem. This can still be used
with the kscan API with the zephyr,kscan-input driver, or use the
input-keymap one to generate input codes instead.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add basic functionality of Renesas SD/MMC driver. It can be used
for both gen3 and gen4 R-car boards, but tested only with H3ULCB,
Salvator XS M3 and Spider boards. This driver working with SDHC
subsystem.
The driver supports regularal reading/writing throught SD/MMC
controller buffer, DMA mode w/o interrupts and timing tuning.
Add gpio5 and sd0 nodes to h3ulcb and salvator xs which are needed
for working with SD cards. The GPIO node is needed for switching
voltage on SD card through gpio regulator driver.
Notes:
* the driver doesn't support SPI mode;
* SCC tuning and DMA mode based on IRQs are enabled by default;
* an address of a data buffer has to be aligned to 128 bytes if it
is not, driver will use non-DMA mode automatically;
* Renesas MMC DMAC doesn't support 64-bit DMA addresses, so for
case when we have 64-bit xref data address we use non-DMA mode;
* SD/MMC controller supports block size between 512 and 1 with
a lot of restrictions, more details you can find in code;
* support of HS400 mode isn't implemented inside driver.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Add device driver for TI TMP114 I2C temperature sensor.
The driver only support basic functionality, i.e. fetch temperature
using default values.
Datasheet:
https://www.ti.com/lit/ds/symlink/tmp114.pdf
Signed-off-by: Fredrik Gihl <fgihl@hotmail.com>
