Adds imx rt support.
Allows n-number of can interfaces based on device-tree.
Adds a "common" irq name.
Added CAN bus pins and dts for 1060 and 1064 EVK.
Signed-off-by: Rick Talbott <rtalbott@fastmail.com>
Enables sdhc on the mimxrt1064_evk board. Configures pinmuxes and device
tree, and updates board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes dependency for I2C so that it's enabled if kscan is enabled.
This is to allow the kscan_ft5336 sample to run.
Note: LVGL has KSCAN as a dependency.
Applies to the mimxrt10{50,60,64}_evk boards.
Signed-off-by: Mark Olsson <mark@markolsson.se>
In conversion of nodelabels to match SoC docs, we missed a case in the
board dts files. However these delete-node commands are not needed as
we normally handle this via the 'status' property being disabled which
enet2 is by default in the SoC dtsi files. So we can safely just remove
the stale /delete-node/ eth1 lines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark all the individual PWMs as disabled in dts and enable the one
explicitly used on the mimxrt1064_evk.dts in the board dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These boards have a SoC with 2 Ethernet controllers but the second
controller it is not wired.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Updates the mcux igpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Removes port configuration support since that feature is deprecated in
the new gpio api.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- mimxrt1015_evk
- mimxrt1020_evk
- mimxrt1050_evk
- mimxrt1060_evk
- mimxrt1064_evk
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds device tree nodes and configures Kconfig defaults for the ft5336
touch panel driver on mimxrt10{50,60,64}_evk boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all i.mx rt socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The i.MX RT1064 evk has one ethernet (10/100M) connector via KSZ8081RNB
phy. Enable related dts nodes and config flags
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Adds a new configuration option to mimxrt10{20,60,64}_evk boards to link
data into external sdram. The default remains to link data into internal
data tightly coupled memory (DTCM).
Note that mimxrt1050_evk is not included because it already has support
for linking data into sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The dts files on these boards had some CONFIG_ defines related to which
memory should be used to hold code. We move this choice out of DTS and
back into Kconfig.
As such, we removed the default setting of 'zephyr,flash' and just
map
CONFIG_CODE_ITCM to:
DT_NXP_IMX_RT_ITCM_0_SIZE
DT_NXP_IMX_RT_ITCM_0_BASE_ADDRESS
CONFIG_CODE_{QSPI,HYPERFLASH} to:
DT_NXP_IMX_FLEXSPI_402A8000_SIZE_1
DT_NXP_IMX_FLEXSPI_402A8000_BASE_ADDDRESS_1
for the mimxrt1050_evk, we remove the default setting of 'zephyr,sram'
and just map:
CONFIG_DATA_DTCM to:
DT_NXP_IMX_DTCM_0_SIZE
DT_NXP_IMX_DTCM_0_BASE_ADDRESS
CONFIG_DATA_SDRAM to:
DT_MMIO_SRAM_80000000_SIZE
DT_MMIO_SRAM_80000000_BASE_ADDRESS
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support files for mimxrt1064_evk, the development board for
i.MXRT1064 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
