Adds a shim layer around the mcux ftm driver to adapt it to the Zephyr
pwm interface.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adjusts the ARM MPU implementation to be compliant to the
recent changes that introduced the opaque kernel data types.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The mimimum mpu size is 32 bytes, but requires mpu base address to be
aligned on 32 bytes to work. Define architecture thread macro when
MPU_STACK_GUARD config to allocate stack with 32 more bytes.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
In the stm32_gpio_flags_to_conf function the configuration
values of the GPIO pin are shifted two times. One in the
stm32-pinctrlf1 header and one in the function. This patch
removes one of those shifts.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch adds the allow flash write CONFIG option to the ARM MPU
configuration in privileged mode.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: David Brown <david.brown@linaro.org>
This patch adds the allow flash write CONFIG option to the NXP MPU
configuration in privileged mode.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: David Brown <david.brown@linaro.org>
Currently Thread time slice is getting reset at end of timer
interrupt. Due to which equal priority threads behind current thread
in ready_q are not getting chance to run and leading to starvation.
This patch handles time slice in _ExcExit section context switch is
required.
Jira: ZEP-2444
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ouput speed of the gpio pins passed via the 'conf' argument was
ignored, causing the speed to always be in its reset state (lowest
possible speed for most pins). This was causing problems for pins that
actually need a speed faster than the default, like the ethernet
controller pins.
Combined with the correct pinmux configuration this fixes problems
of the olimex_stm32_e407 board not being able to send ethernet data.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Historically, stacks were just character buffers and could be treated
as such if the user wanted to look inside the stack data, and also
declared as an array of the desired stack size.
This is no longer the case. Certain architectures will create a memory
region much larger to account for MPU/MMU guard pages. Unfortunately,
the kernel interfaces treat both the declared stack, and the valid
stack buffer within it as the same char * data type, even though these
absolutely cannot be used interchangeably.
We introduce an opaque k_thread_stack_t which gets instantiated by
K_THREAD_STACK_DECLARE(), this is no longer treated by the compiler
as a character pointer, even though it really is.
To access the real stack buffer within, the result of
K_THREAD_STACK_BUFFER() can be used, which will return a char * type.
This should catch a bunch of programming mistakes at build time:
- Declaring a character array outside of K_THREAD_STACK_DECLARE() and
passing it to K_THREAD_CREATE
- Directly examining the stack created by K_THREAD_STACK_DECLARE()
which is not actually the memory desired and may trigger a CPU
exception
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Move to using the generated IRQ defines from the DTS instead of soc.h.
This change also fixes a minor bug in that the error irq priority wasn't
getting correctly picked up from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F3 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework stm32f1 pinmux code for future dts based pinmux code
generation.
Pin configuration is now done directly thanks to gpio port
configuration. Reference to pseudo alternate functions are
now removed same as the use of pins[] array.
Pins function (uart tx for instance) is set implicitly by
defining gpio mode and configuration.
This behavior is specific to stm32f10x series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In L4 series, select HAS_STM32CUBE is done per soc.
This could be factorized in Kconfig.series.
Aim is to lower the steps to add a new SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With introduction of commit "pinmux: stm32: directly return error if
stm32_get_pin_config fails", pin configuration fails when
pins are not configured in pins[] array.
This was the case for configuration UART1 assigned on PB6/PB7.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
If the adc driver configuration is enabled (CONFIG_ADC=y), then enable
the mcux shim driver by default for all Kinetis SoCs.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux adc16 driver to adapt it to the Zephyr
adc interface.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add a STM32 LL based driver for the RNG processor. The RNG processor
is a random number generator, based on a continuous analog noise, that
provides a random 32-bit value to the host when read. The RNG passed
the FIPS PUB 140-2 (2001 October 10) tests with a success ratio of 99%.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enabled the boot_time test on ARM SoCs, set __start_time_stamp on ARM
since we don't have a free running counter similar to TSC on x86.
Also moved to printing the values out as %u to increase the range of
values.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In added mode flash operation are performed in timeslice
(in radio idle time).
Kconfig for mode enabling CONFIG_SOC_FLASH_NRF5_RADIO_SYNC.
Erase and write API implementations were rewritten and preserved against
concurrent execution.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Board port was done before the yaml transition, so was missing a
cc2650_sensortag.yaml. As such when we build all the test we get a few
build errors that we also fixed up.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add configuration and memory definitions to support STM32F103x8
Medium-density performance line SoC with 64 KB Flash.
Merge multiple files into single Kconfig.defconfig.stm32f103xx
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Since not all socs from f3 series (i.e stm32f334x8 no MPU) have MPU
capability, add capability only for MPU capable socs in Kconfig.soc
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
As other stm32 series support MPU, move common file in a file tree
useable by socs from other series
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clearing fields in the region descriptor attributes doesn't always have
the expected effect of revoking permissions. In the case of bus master
supervisor mode fields (MxSM), setting to zero actually enables read,
write, and execute access.
When we reworked handling of region descriptor 0, we inadvertently
enabled execution from RAM by clearing the MxSM fields and enabling the
descriptor. This caused samples/mpu_test run to throw a usage fault
instead of an MPU-triggered bus fault.
Fix this by setting all the MxSM fields to 2'b11, which gives supervisor
mode the same access as user mode.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Both the ARM and NXP MPU drivers incorrectly calculated the region index
by assuming the region type (e.g., THREAD_STACK_GUARD_REGION) was
zero-indexed, when in reality it is one-indexed. This had the effect of
wasting one region.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The NXP MPU requires special handling of region descriptor 0 to
guarantee that the debugger has access to the entire address space. It
does not allow writes from the core to affect the start or end
addresses, or the permissions associated with the debugger.
The original implementation of this driver attempted to work around
region descriptor 0, resulting in an off-by-1 error caught by Coverity.
Instead, define region descriptor 0 explicitly in the mpu_regions array,
and add some asserts to ensure that one doesn't try to change its start
or end addresses. This has an added benefit such that more permissions
can be enabled in region 0 if desired, whereas the previous
implementation always forced all writable permissions to be cleared.
Coverity-CID: 170473
Jira: ZEP-2258
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The original implementation of _get_num_regions() parsed the CESR[NRGD]
register field to determine the number of mpu region descriptors
implemented in hardware. There was a possible path in the code to return
zero, which would cause underflow later on in arm_core_mpu_configure().
Coverity complained despite an assert to catch this condition. Instead,
use a preprocessor macro from mcux that defines the number of mpu region
descriptors.
Coverity-CID: 169811
Jira: ZEP-2208
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
