This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
The pm_constraint_* APIs were effectively used by the policy manager
only. This patch renames the API to the policy namespace and makes its
naming more explicit:
- pm_constraint_set -> pm_policy_state_lock_get()
- pm_constraint_release -> pm_policy_state_lock_put()
- pm_constraint_get -> pm_policy_state_lock_is_active()
The reason for these changes is that constraints can be of many types:
allow/disallow states, impose latency requirements, etc. The new naming
also makes explicit that the API calls will influence the PM policy
behavior.
All drivers and documentation have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Replace all get_dev_data()/get_dev_config() accessor utilities with
dev->data and dev->config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Port some drivers to the recently introduced macros to showcase its
usage and be able to do some initial testing (nRF52840).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In case when we have multiple devices connected to the
one SPI interface the initial state of CS gpios after
MCU reset is floating and it might be low that prevents us from
communicating between particular devices. Fix that by
initializing all provided cs gpios and setting them as inactive.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
The PM callback is no longer referenced as "pm_control" but
"pm_action_cb", so reflect this new naming on the callbacks.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Instead of passing target states, use actions for device PM control.
Actions represent better the meaning of the callback argument.
Furthermore, they are more future proof as they can be suitable for
other PM actions that have no direct mapping to a state. If we compare
with Linux, we could have a multi-stage suspend/resume. Such scenario
would not have a good mapping when using target states.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Return -ENOTSUP if the requested state is not supported
- Remove redundant "noop style" functions.
- Use switch everywhere to handle requested state (not necessary in all
drivers, but better take off with consistency in place after current
changes).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM control function will only be called if the requested
state is different from the current one. A significant amount of drivers
were checking for state changes, now unnecessary. This patch removes all
this redundant logic.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Since the state is no longer modified by the device PM callback, just
use the state value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is now invoked to set the device PM state in all cases, so
the usage of ctrl_command is redundant.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem already holds the device state, so there is no
need to keep duplicates inside the device. The pm_device_state_get has
been refactored to just return the device state. Note that this is still
not safe, but the same applied to the previous implementation. This
problem will be addressed later.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is not used anymore, so just delete it from the pm_control
callback signature.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
the device PM callback is not used anymore by the device PM subsystem,
so remove it from all drivers/tests using it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move all PM_DEVICE_STATE_* definitions to an enum. The
PM_DEVICE_STATE_SET and PM_DEVICE_STATE_GET definitions have been kept
out of the enum since they do not represent any state. However, their
name has not been changed since they will be removed soon.
All drivers and tests have been adjusted accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The context parameter used across device power management is
actually the power state. Just use it and avoid a lot of
unnecessary casts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Remove conditionals (PM_DEEP_SLEEP_STATES and PM_SLEEP_STATES) from
power management code. Now these features are always available when
power management is enabled.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Migrate the whole pm subsystem to use new power states information
from power_state.h and get states and residency properties from
device tree.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The cc13xx_cc26xx driver uses "inst" so we need to use
DEVICE_DT_INST_DEFINE instead of DEVICE_DT_DEFINE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Keep locking for SPI_LOCK_ON from the first call of transceive until
spi_release release the lock. Use owner parameter to in the spi_context
to store the owner of the lock.
The locking is in line with the SPI_HOLD_ON_CS
Signed-off-by: Stefan Bigler <stefan@bigler.io>
For drivers that support CONFIG_DEVICE_POWER_MANAGEMENT there are some
cases that look like:
#ifdef CONFIG_DEVICE_POWER_MANAGEMENT
DEVICE_DEFINE()
#else
DEVICE_AND_API_INIT()
#endif
There is no need to special case this as the pm_control_fn argument to
DEVICE_DEFINE will just be ignored in the
!CONFIG_DEVICE_POWER_MANAGEMENT case. So we can cleanup the code a
little and remove the #else cases for the drivers that do this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The power configuration is dependent on which SPI is physically used.
In order to allow DT_INST_FOREACH_STATUS_OKAY() to iterate through
instances without the assumption that index 0 corresponds to SPI0
(which would be incorrect in the case when only SPI1 is enabled),
we need to check the base address to identify which SPI is being dealt
with.
Fixes#25673
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clean up as we wish to move away from using these Kconfig settings.
Also removing them from the boards' default config.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Replace DT_CPU_CLOCK_FREQUENCY with a PATH based reference to cpu@0
(DT_PATH(cpus, cpu_0)) and than getting the clock_frequency property:
DT_CPU_CLOCK_FREQUENCY -> DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
This lets us remove DT_CPU_CLOCK_FREQUENCY from dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Use of macros such as SYS_POWER_STATE_SLEEP_2 needs to be guarded by
making sure CONFIG_SYS_POWER_SLEEP_STATES is defined.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
