Extensions could have used logging, when log processing is
deferred, the logging thread can run after the extension has
been unloaded and thereby access invalid memory addresses.
Make sure to flush all logs before unloading extensions.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Zephyr already has various FlexIO drivers but imxrt11xx didn't enable
the base flexio peripheral.
Signed-off-by: Peter van der Perk <peter.vanderperk@nxp.com>
Due to issues with running the watchdog test in a fully
automated manner on the IT8XXX2_EVB, it was previously removed.
However, a fix has now been merged, and it should be operational
on this board once again.
Signed-off-by: Patryk Kuniecki <patryk.kuniecki@intel.com>
Flash partition was defining a scratch area which was implying the use
of mcuboot BOOT_SWAP_USING_SCRATCH f/w update method.
By removing this partition, mcuboot will automatically use
BOOT_PREFER_SWAP_MOVE method which should be prefered as it levels
flash wear. Incidentally increase slot1 by one sector (as this is
preferred for the swap method).
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
1) After the wifi driver successfully connects to the AP,
the dormant state should be set to OFF.
Once a deauth/disassoc frame is received or link lost occurs,
the dormant state should be set to ON.
2) Enable CONFIG_NET_TC_SKIP_FOR_HIGH_PRIO and CONFIG_NET_CONTEXT_PRIORITY
to push high priority packets directly to network driver.
Signed-off-by: Gang Li <gang.li_1@nxp.com>
The STM32H5x adc has a special option register that
needs to be set when using channel 0 on adc1.
fixes: #77618
Signed-off-by: Lars Jeppesen <lje@foss.dk>
The gen_kobject_list.py script expects the __subystem declaration to end
with _driver_api. Adjust the stepper api and existing driver implementation
accordingly.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Update the EDTT module to:
b9ca3c7030518f07b7937dacf970d37a47865a76
Including the following:
* b9ca3c7 Fix for for python >= 3.11
* fe9b1d1 Corrected ISO interval for LL/CIS/PER/BV-05-C
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Some hardware configuration require rely on the ALERT/RDY
pin to know when and ADC conversion is completed.
The polling thread is left as fallback, when the pin
is not defined.
Signed-off-by: Efrain Calderon <efrain.calderon.estrada@gmail.com>
Add a new macro, DT_ANY_COMPAT_HAS_PROP_STATUS_OKAY
name, evaluates to 1 if any enabled instance of `compat` has the
property or to zero if it hasn't.
This macro can be useful in drivers for a family of devices.
Signed-off-by: Efrain Calderon <efrain.calderon.estrada@gmail.com>
This example demonstrates I2S audio playback combined with the codec
API. It can use the dmic API for audio input.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Add Flexcomm signal sharing configuration for the mimxrt595s/cm33 and
mimxrt685s/cm33 SoCs. Properly instantiate the I3C peripheral for
interfacing with the WM8904's control port. Modify pinctrl DTs of
mimxrt595_evk/mimxrt595s/cm33 and mimxrt685_evk/mimxrt685s/cm33.
Instantiate the WM8904 codec for said boards.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Add clock config for Flexcomm peripherals functioning as I2S interfaces.
Add MCLK clock config for the WM8904 codec located on the mimxrt595_evk
and mimxrt685_evk boards.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Add sample rates. Add dai_route_t enum to allow codec configuration for
duplex operation. Allow for audio inputs to be controlled. Add functions
for signal routing.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Enable DMIC clock in soc.c - attach to chip's audio PLL. Add pinmux
definitions for the DMIC peripheral. Add nodes to SoC's device tree for
the DMIC peripheral and its audio channels. Configure the DMIC
peripheral in board's device tree to enable audio capture.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Commit consists of minimal set of overlays need to run tests
and samples. Additionally disables nRF54L15 platform in cpp98
tests, because unnamed unions are not supported.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
timeutil internally uses 1900 as base year for calculation,
that is hidden from caller context. Thus declared a macro in
the public header file, and uses that macro will let caller adjust the
calulations accordingly.
Signed-off-by: Anuj Pathak <anuj@croxel.com>
find the headset which a2dp related record len is SEQ32,
fix sdp_client_get_total too because it doesn't handle
SEQ32 too.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
As the .bin & .hex build output is optional
and it can be disabled by CONFIG_BUILD_OUTPUT_BIN/HEX,
add support for the mandatory .elf build output
to the linkserver runner flash command.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Following addition of a `name` to hal_stm32 module, the command to fetch
blobs that are required to build BLE applications on STM32WBA socs is now
changed from `west blob fetch stm32` to `west blob fetch hal_stm32`.
Update documentation and warn users in migration guide.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
