This commit updates the HMC5883L driver to use the new GPIO API.
Also add a note explicitly describing the active state of the DRDY
pin in the binding file.
Tested on frdm_k64f.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update sample overlay for missing chip select and to deconflict with
UART TXD. Add GPIO flags to configuration state. Replace callback
enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the gpio_counter sample app for the UP Squared board:
() Update configuration calls to use new flags.
() Separate pin configuration into setting it to input, and
setting the pin for interrupt.
() Use gpio_pin_set() instead of gpio_pin_write().
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a board overlay for up_squared to be used with
the GPIO sample. Using the overlay is because the pins
being used are not actually LED and switch but GPIO pins
used as such.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update sample application to use new GPIO API:
- GPIO flags defined by the devicetree
- replace gpio_pin_write with gpio_pin_set function
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update ALERT active level in all devicetree files. Capture GPIO flags
in static configuration. Add internal API to enable and disable
interrupt, to release the handlers when an alert occurs, and to
re-enable the signal when the handler completes. Check for alerts
received during periods when the interrupt was disabled.
Extend the example to handle both above and below range triggers and
alerts that are present on startup.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert the GPIO based driver to the new GPIO API. (Only the
gpio_configure() call is affected).
Move configuration to DT where appropriate for both SPI and GPIO
drivers, only leaving the SPI vs. GPIO decision in Kconfig (in
addition to the basic enable for the driver.) Move some files around
to clean up as a result of this change.
led_ws2812 sample changes:
- make the pattern easier to look at by emitting less light
- use led_strip alias from DT to get strip device, allocate
appropriate struct led_rgb buffer, etc.
- move the pins around and remove 96b_carbon support (I have no board
to test with)
GPIO driver specific changes:
- str is required to write OUTSET/OUTCLR, not strb. The registers
are word-sized.
- the str[b] registers must all be in r0-r7, so "l" is the correct GCC
inline assembly constraint for both "base" and "pin"
SPI driver specific changes:
- match the GPIO driver in not supporting the update_channels API
method, which never made sense for this type of strip
- return -ENOMEM when the user tries to send more pixel data
than we have buffer space for instead of -EINVAL
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Switched from deprecated gpio_pin_write to gpio_pin_set and also add the
LED GPIO flags to the gpio configuration.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Convert the sample to use the new GPIO API and additionally:
- add some error messages for unsuccessful GPIO API calls
- correct the index of `def_val` element used in the `right_button`
callback, to match the one used when the callback is installed
- use flags defined in devicetree for the pin that drives the LED
(for consistency, as this does not make much difference for a pin
that is only toggled)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Implement the new GPIO driver APIs for the HT16K33 and update the
driver to use the new GPIO flags.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Update gpio_pin_configure() to take into account GPIO flags defined by
the devicetree. Use gpio_pin_get/gpio_pin_set to verify reading/writing
of logical pin values. Use gpio_pin_interrupt_configure() to configure
interrupts.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Eliminates CI build warnings such as this which breaks the build:
warning: NET_SOCKETS_POSIX_NAMES
(defined at subsys/net/lib/sockets/Kconfig:13) was assigned the value
'n' but got the value 'y'.
The testcase involves no offloading, which means it does not apply to
cc32xx.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
This PR eliminates the Kconfig warnings seen in build by setting the
options to the appropriate values for cc32xx platforms. They were
causing CI failures.
Fixes#22388
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Use the voltage divider devicetree binding to demonstrate measurement
of battery voltage for two Nordic-based boards that have the necessary
circuitry.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This test uses bare variables to synchronize state between threads,
but had forgotten volatile qualifiers on all the data. So the
compiler was free to reorder and make assumptions that aren't valid
when the values are being written from other CPUs.
Single-cpu operation was fine because the code would always hit an
external function call like k_sleep() that would force it to re-read
from memory every time there was a context switch (timeslicing isn't
enabled on this test and the threads are cooperative), but on SMP the
volatiles can change at any time and we could see spurious state
mixups and hangs.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Add Kconfig option NET_SAMPLE_SEND_ITERATIONS that sets the number of
times the Zephyr echo client sample sends its data. By default the
value is zero, which means indefinite, and demonstrates the same
behavior as before.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Extends the keyboard scan callback row and column arguments from 8-bits
to 32-bits to support a touch panel driver implementation.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This count is assigned to CONFIG_BT_ACL_RX_COUNT which expects a number
in the range of 1-64, otherwise kconfig fails.
Fixes#22259
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Write initial content of the display before blanking_off.
This allow faster update of the electronic ink displays as
the controller do not update the pannel when the banking
is enabled (currently this behaviour is only implemented
in gd7965 driver).
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Switch to `NET_SOCKET_REGISTER` mechanism over the offloaded API
registration.
Including the following fixes from the review:
* The fd returned by the socket accept call needs to be finalized,
similar to how it is done for socket creation.
* sl_RecvFrom() in TI SimpleLink Host driver does not support NULL
pointers for 'from' address and address length, and sl_SendTo() does
not ignore the destination address when in connection mode, so passing
NULL would cause a failure. These issues have been reported to TI
(CC3X20SDK-1970, CC3X20SDK-1971).
Let's use sl_Recv and sl_Send to implement recvfrom/sendto in the case
of NULL addresses.
* simplelink_poll() should not process negative file descriptors in the
fds array after sl_Selecti() returns. A negative fd value indicates
that the entry is invalid and should be ignored.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Added support for native_posix targets.
Added setting FS back-end initialization which is used by
native_posix targets.
The test harness was adapted to the fact that key-value pairs
read-out order might be different for each back-end when call
settings_load().
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Added sample for the settings subsystem.
The sample shows how to:
-initialize and register handler
-implement handles
-save and load data using registered handlers
-load subtree
-save or delete a certain value
-load subtree values or a value directly
- example on how to write data to the
setting destination and how to read data
from the setting destination using runtime API.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Fixed bug in udp.c in echo_client and echo_server samples.
The bug causes UDP sockets to not close if socket id is 0.
Signed-off-by: Magne Værnes <magne.varnes@nordicsemi.no>
Make sure that the echo-server compiles ok if IPv6 or IPv4 is
disabled when VLAN is enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adjust the configuration file, disable the SPI
driver and enable the QSPI driver and flash node.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
A configuration file attempted to select the external flash memory for
this platform, but there was no overlay that redefined the storage
partition to be on that device rather than the SOC flash.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Change to display RSSI and SNR values of the received data.
This change helps to test LoRa's communication distance and
communication quality.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
In order to better handle incoming data, wait() should return
the # of sockets with data returned by poll().
Based on this new return value, we can call mqtt_input() in a
smarter way.
Signed-off-by: Michael Scott <mike@foundries.io>
Now that mqtt_live() can send an EAGAIN message meaning: no ping
was generated, let's handle that in process_mqtt_and_sleep() by
skipping the call to mqtt_input() since no data will be expected.
Signed-off-by: Michael Scott <mike@foundries.io>
Introduce a new counter API function for reading the current counter
value (counter_get_value()) and deprecate the former counter_read() in
favor of this.
Update all drivers and calling code to match the new counter API.
The previous counter driver API function for reading the current value
of the counter (counter_read()) did not support indicating whether the
read suceeded. This is fine for counters internal to the SoC where the
read always succeeds but insufficient for external counters (e.g. I2C
or SPI slaves).
Fixes#21846.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Make sure that we do not calculate terminating \n when comparing
the received data to sent data because the \n is not part of
the lorem_ipsum buffer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This sample keeps failing in CI due to some SMP issues currently being
addressed. Exclude until we have a fix.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Sample app compiled with the GSM modem driver enabling PPP.
This sample was tested with a Reel Board UART_1 connected via the
external board/connector and a FONA 808 modem. Reel board specific
suppor is found in boards/.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
