Error handling was missing in numerous places, mostly on GPIO related
callbacks. Some error codes were not correct (-EINVAL vs -ENODEV) and in
some cases error was not propagated correctly.
Fixes#38117
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In drivers/sensor/CMakeLists.txt, we have various lines like this:
add_subdirectory_ifdef(CONFIG_FOO foo)
Then drivers/sensor/foo/CMakeLists.txt says:
zephyr_library()
zephyr_library_sources_ifdef(CONFIG_FOO foo.c)
This is redundant; the foo/CMakeLists.txt won't be added to the build
system unless CONFIG_FOO=y in the first place, so there's no need for
extra boilerplate testing it again.
Remove all these unnecessary instances in each sensor driver's
CMakeLists.txt using this pattern:
zephyr_library()
zephyr_library_sources(foo.c)
In a couple of places, the '.c' extension is missing. Add them in for
consistency when that happens.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add a possibility to get values of accelerometer measurement for
all 3 axis of accelerometer with one channel_get().
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Currently there is no way to distinguish between a caller
explicitly asking for a semaphore with a limit that
happens to be `UINT_MAX` and a semaphore that just
has a limit "as large as possible".
Add `K_SEM_MAX_LIMIT`, currently defined to `UINT_MAX`, and akin
to `K_FOREVER` versus just passing some very large wait time.
In addition, the `k_sem_*` APIs were type-confused, where
the internal data structure was `uint32_t`, but the APIs took
and returned `unsigned int`. This changes the underlying data
structure to also use `unsigned int`, as changing the APIs
would be a (potentially) breaking change.
These changes are backwards-compatible, but it is strongly suggested
to take a quick scan for `k_sem_init` and `K_SEM_DEFINE` calls with
`UINT_MAX` (or `UINT32_MAX`) and replace them with `K_SEM_MAX_LIMIT`
where appropriate.
Signed-off-by: James Harris <james.harris@intel.com>
This patch fixes warnings for unused variables when acceleremoter
range and sampling frequency are set to values different from
the defaults.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
The thresholds for activity/inactivity in the adxl362 acceleromter have
two parameters that can be configured. Currently the threshold is
configurable via the KConfig variables CONFIG_ADXL362_ACTIVITY_THRESHOLD
and CONFIG_ADXL362_INACTIVITY_THRESHOLD which configure repectively the
value in the THRESH_ACT and THRESH_INACT registers.
The other parameter that can be configured is the time by changing the
values in the registers TIME_ACT and TIME_INACT, but this values are
hardcoded to 1 (see lines 653 and 675 in adxl362.c), this patch adds
support for configuring those values in KConfig as
CONFIG_ADXL362_ACTIVITY_TIME and CONFIG_ADXL362_INACTIVITY_TIME.
Signed-off-by: Xavier Naveira <xnaveira@gmail.com>
It is necessary to wrap the device pointer into data.
Which was done already on most of them when global trigger is enabled.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some sensor drivers modify there struct's based on DT defines. In those
cases we need to make sure that DT_DRV_COMPAT is set on all the source
files associated with that driver. This updates any such files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sensor.h to drivers/sensor.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It is recommended that multibyte (burst) transfers are used to read
acceleration and temperature data. This ensures the data is concurrent
and complete.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
This commit consolidates the temperature conversion into a single
location and subtracts the bias from the measurement using values from
the datasheet. Also magic numbers have been replaced with more
descriptive macros.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
This driver uses magic numbers which are incorrect. A correct conversion
is done using the LSB/g scale factors given by Table 1 in the
specifications section of the ADXL362 (Rev. F) datasheet. The entire
conversion has also been consolidated into a signal function.
The sensitivity and offset of the accelerometer values actually vary
with the supply voltage and temperature. Using datasheet provided values
for 25 C and 2.0 V is the best we can do. Users will need to apply
sensitivity and offset corrections for their application.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The return code check and error return on the interrupt register
configuration function call should be included in the #if defined
region.
Fixes#16159
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Clear status bits before mapping them to the interrupt pin, so the
interrupt will occur on the next event instead of a pending event. Also
the status bits are cleared independently, because the threshold and
data ready functions can be enabled simultaneously.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Enabling and disabling the GPIO callbacks is error prone and unnecessary
since the trigger data is protected with a mutex, so it has been
removed. This resolves the following issues:
- The GPIO callbacks are not being re-enabled properly in the error path
of the trigger setting function.
- The device pointer used in the GPIO callback to retrieve the ADXL362
driver configuration data is the GPIO device not the ADXL362 device,
so this cast is invalid and the int_gpio field is garbage.
- There are potential timing issues between enabling interrupts and
re-enabling the callbacks.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Commit 11295c1 added Kconfig options for interrupt mode, but then hard
coded the interrupt mode. This commit uses the Kconfig option to set
the interrupt mode.
Applications expecting the interrupt mode to be something other than
the default will need to be updated.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The default case of the switch statement jumps over the unlocking of the
trigger mutex. This has been fixed with more granular locking which has
the added benefit of being more explicit about what is being protected.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Updated to add support for CS. DT config names updated
to adhere to the DTS naming convention. Init and SPI
configuration now follows the device datasheet.
Signed-off-by: Henrik Malvik Halvorsen <henrik.halvorsen@nordicsemi.no>
Converts the adxl362 sensor driver to get the device name and spi slave
properties from the device tree rather than Kconfig. Updates the
build_all test accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
