sw_isr_table has two entries, an argument and an ISR function. The
comment on struct _isr_table_entry in include/sw_isr_table.h says that
"This allows a table entry to be loaded [...] with one ldmia
instruction, on ARM [...]". Some arch, e.g. SPARC, also has a double
word load instruction, "ldd", but the instruct must have address align
to double word or 8 bytes.
This commit makes the table alignment configurable. It allows each
architecture to specify it, if needed. The default value is 0 for no
alignment.
Signed-off-by: Yasushi SHOJI <y-shoji@ispace-inc.com>
The libc hooks for Newlib requires CONFIG_SRAM_SIZE and
the symbol "_end" at the end of memory. This is in preparation
for enabling Newlib for x86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ARCH_CHOICE symbol on the arch/Kconfig choice for Architecture
selection, allows for multiple definitions of the choice group which
makes it possible for out-of-tree architectures to add entries to the
list as needed.
For example, in $(ARCH_DIR)/$(ARCH)/Kconfig by adding something like;
choice ARCH_CHOICE
config xARCH
bool "xARCH architecture"
endchoice
No functional change expected.
Signed-off-by: Danny Oerndrup <daor@demant.com>
Support for Floating Point (both un-sharing and sharing
registers mode) is currently implemented for ARM and X86
architectures, so reflect this in the Kconfig symbol
definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This is the generic symbol to select or otherwise test for when 64-bit
compilation is desired. Two trivial usages of this symbol are also
included.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The original value of 256 was selected more or less randomly
and special cases keep proliferating. Until we have a formal
method of proving maximum syscall stack depth, set to 1024.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add SYS_POWER_ prefix to HAS_STATE_SLEEP_, HAS_STATE_DEEP_SLEEP_
options to align them with names of power states they control.
Following is a detailed list of string replacements used:
s/HAS_STATE_SLEEP_(\d)/HAS_SYS_POWER_STATE_SLEEP_$1/
s/HAS_STATE_DEEP_SLEEP_(\d)/HAS_SYS_POWER_STATE_DEEP_SLEEP_$1/
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
There exists SoCs, e.g. STM32L4, where one of the low power modes
reduces CPU frequency and supply voltage but does not stop the CPU. Such
power modes are currently not supported by Zephyr.
To facilitate adding support for such class of power modes in the future
and to ensure the naming convention makes it clear that the currently
supported power modes stop the CPU this commit renames Low Power States
to Slep States and updates the documentation.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Since #14545 was merged building with USERSPACE and NO_OPTIMIZATIONS
has been broken due to #5226.
To fix#5226 we increase the size of KOBJECT_TEXT_AREA when
NO_OPTIMIZATIONS.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Currently thread abort doesn't work if a thread is currently scheduled
on a different CPU, because we have no way of delivering an interrupt
to the other CPU to force the issue. This patch adds a simple
framework for an architecture to provide such an IPI, implements it
for x86_64, and uses it to implement a spin loop in abort for the case
where a thread is currently scheduled elsewhere.
On SMP architectures (xtensa) where no such IPI is implemented, we
fall back to waiting on an arbitrary interrupt to occur. This "works"
for typical code (and all current tests), but of course it cannot be
guaranteed on such an architecture that k_thread_abort() will return
in finite time (e.g. the other thread on the other CPU might have
taken a spinlock and entered an infinite loop, so it will never
receive an interrupt to terminate itself)!
On non-SMP architectures this patch changes no code paths at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Some more were added since the cleanup pass in June 2018. See e.g.
commit 2d50da70a1 ("drivers: ipm: Kconfig: Remove redundant 'default n'
properties") for a motivation. It also avoids people wondering whether
or not they need to put in 'default n'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
CPU_LPS_n name used to indicate a low power state is cryptic and
incorrect. The low power states act on the whole SoC and not exclusively
on the CPU. This patch renames CPU_LPS_n states to LOW_POWER_n. Also
HAS_ pattern for Kconfig options is used in favor of a non standard
_SUPPORTED. Naming of deep sleep states was adjusted accordingly.
Following is a detailed list of string replacements used:
s/SYS_POWER_STATE_CPU_LPS_(\d)_SUPPORTED/HAS_STATE_LOW_POWER_$1/
s/SYS_POWER_STATE_CPU_LPS_(\d)/SYS_POWER_STATE_LOW_POWER_$1/
s/SYS_POWER_STATE_DEEP_SLEEP_(\d)_SUPPORTED/HAS_STATE_DEEP_SLEEP_$1/
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit removes dependency on SYS_POWER_LOW_POWER_STATES_SUPPORTED,
SYS_POWER_DEEP_SLEEP_STATES_SUPPORTED Kconfig options. Power management
SYS_POWER_LOW_POWER_STATES, SYS_POWER_DEEP_SLEEP_STATES options depend
now directly on specific power states supported by the given SoC. This
simplifies maintenance of SoC Kconfig files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Instead of having to enable ramfunc support manually, just make it
transparently available to users, keeping the MPU region disabled if not
used to not waste a MPU region. This however wastes 24 bytes of code
area when the MPU is disabled and 48 bytes when it is enabled, and
probably a dozen of CPU cycles during boot. I believe it is something
acceptable.
Note that when XIP is used, code is already in RAM, so the __ramfunc
keyword does nothing, but does not generate an error.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
128 already gets exceeded in a lot of cases, and the binaries
with the new SDK are very slightly larger. Just kick this up
to 256 and get rid of all the exceptions.
Fixes: #13594
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some of power states used numerical suffix while otthers not.
This commit adds proper suffix to all power state names.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
f
This commit changes the names of SYS_POWER_DEEP_SLEEP* Kconfig
options in order to match SYS_POWER_LOW_POWER_STATE* naming
scheme.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The SYS_POWER_LOW_POWER_STATE_SUPPORTED and SYS_POWER_LOW_POWER_STATE
suggests one low power state but these options control multiple
low power state. This commit uses plural in the names to indicate
that.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Introduces the ARCH_ROOT argument, similar to BOARD_ROOT and SOC_ROOT.
This enables support for out-of-tree architectures.
The ARCH_ROOT out-of-tree layout is expected to be the following:
* ${ARCH_ROOT}/arch/${ARCH}/
* ${ARCH_ROOT}/include/arch/${ARCH}/ (Optional)
Signed-off-by: Klaus Petersen <kape@oticon.com>
This commit introduces a new Kconfig option symbol,
MPU_REQUIRES_NON_OVERLAPPING_REGIONS, to signify the use of an
MPU architecture that requires the active MPU regions be
non-overlapping. This requirement concerns the standard
(unmodified) ARMv8-M MPU implementation. For that, we select
the option in the definition of ARM_MPU, if the CPU architecture
is ARMv8-M (Baseline or Mainline).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In #9717, 777407b9ea
coverage support was broken for all NATIVE_APPLICATION except
native_posix
This includes the nrf52_bsim board
Fix it.
Fixes: #13009
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Now that all supported xtensa boards use DTS we can move the Kconfig
setting to the arch level. Remove HAS_DTS from board Kconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
dts will now generate DT_SRAM_BASE_ADDRESS, DT_SRAM_SIZE,
DT_FLASH_BASE_ADDRESS, and DT_FLASH_SIZE defines. Kconfig can utilize
these defines to set defaults for the CONFIG_ variants.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds all the required hooks needed in the kernel to
get the coverage reports from ARM SoCs.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This patch provides support for generating Code coverage reports.
The prj.conf needs to enable CONFIG_COVERAGE. Once enabled, the
code coverage data dump now comes via UART.
This data dump on the UART is triggered once the main
thread exits.
Next step is to save this data dump on file. Then run
scripts/gen_gcov_files.py with the serial console log as argument.
The last step would be be to run the gcovr. Use the following cmd
gcovr -r . --html -o gcov_report/coverage.html --html-details
Currently supported architectures are ARM and x86.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This patch adds a x86_64 architecture and qemu_x86_64 board to Zephyr.
Only the basic architecture support needed to run 64 bit code is
added; no drivers are added, though a low-level console exists and is
wired to printk().
The support is built on top of a "X86 underkernel" layer, which can be
built in isolation as a unit test on a Linux host.
Limitations:
+ Right now the SDK lacks an x86_64 toolchain. The build will fall
back to a host toolchain if it finds no cross compiler defined,
which is tested to work on gcc 8.2.1 right now.
+ No x87/SSE/AVX usage is allowed. This is a stronger limitation than
other architectures where the instructions work from one thread even
if the context switch code doesn't support it. We are passing
-no-sse to prevent gcc from automatically generating SSE
instructions for non-floating-point purposes, which has the side
effect of changing the ABI. Future work to handle the FPU registers
will need to be combined with an "application" ABI distinct from the
kernel one (or just to require USERSPACE).
+ Paging is enabled (it has to be in long mode), but is a 1:1 mapping
of all memory. No MMU/USERSPACE support yet.
+ We are building with -mno-red-zone for stack size reasons, but this
is a valuable optimization. Enabling it requires automatic stack
switching, which requires a TSS, which means it has to happen after
MMU support.
+ The OS runs in 64 bit mode, but for compatibility reasons is
compiled to the 32 bit "X32" ABI. So while the full 64 bit
registers and instruction set are available, C pointers are 32 bits
long and Zephyr is constrained to run in the bottom 4G of memory.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
As this was written before, a 'FLAOT' menu entry was present, and to
see what kind of features or configuration it had, one had to navigate
into the menu to determine if anything related to 'FLOAT' was enabled
at all.
Now there is an unchecked box on the 'FLOAT' menu when it is disabled,
which clearly expresses that it is disabled without the need to enter
the menu entry.
This change only changes the menu layout, and not the dependencies of
any options.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
When code relocation feature with userspace mode is turned on we
need a bit more memory to fit the text section for these 2
generated files.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This commit exposes k_mem_partition_attr_t outside User Mode, so
we can use struct k_mem_partition for defining memory partitions
outside the scope of user space (for example, to describe thread
stack guards or no-cacheable MPU regions). A requirement is that
the Zephyr build supports Memory protection. To signify this, a
new hidden, all-architecture Kconfig symbol is defined (MPU). In
the wake of exposing k_mem_partition_attr_t, the commit exposes
the MPU architecture-specific access permission attribute macros
outside the User space context (for all ARCHs), so they can be
used in a more generic way.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add a "nocache" read-write memory section that is configured to
not be cached. This memory section can be used to perform DMA
transfers when cache coherence issues are not optimal or can not
be solved using cache maintenance operations.
This is currently only supported on ARM Cortex M7 with MPU.
Fixes#2927
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This option is useful to have for a flatter hierarchy for one-off SoCs
that aren't split into family and series from the silicon vendor
perspective.
The commit saying it was going to go away is from 2 years ago; it
hasn't happened and it doesn't seem to need to happen. Just delete it.
Signed-off-by: Marti Bolivar <marti@foundries.io>
In the past the capability to install interrupts at runtime was
removed due to lack of use-cases for Zephyr's intended targets.
Now we want to support hypervisor applications like ACRN where
virtual devices are presented to the kernel using PCI enumeration,
and the interrupt configuration is not known at build time.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Remove either duplicate settings between arch & board, or just set
HAS_DTS at the arch level since all the boards for a given arch support
DTS now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit increases the privilege stack size to 512 bytes,
when building with support for built-in stack-overflow checking.
This is in alignment with #10729, which increases the privilege
stack size when MPU-based stack guarding is enabled.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes a Kconfig symbol hierarchy which allows
the user to build Zephyr Secure and Non-Secure images on ARMv8-M
MCUs with support for Trusted Execution. However, the high-level
configuration structure is generic, thus, can be potentially
used for any platform that supports Trusted Execution.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This patch adds Big Endian architecture support. Even if a compiler
generating big endian object files is used, our linker script, or
include/linker/linker-tool-gcc.h to be precise, has default output
format as little endian.
This patch adds a hidden config CONFIG_BIG_ENDIAN, which should be set
by big endian architectures or a SoC's, and adds an condition to
switch OUTPUT_FORMAT in our linker.cmd.
Signed-off-by: Yasushi SHOJI <y-shoji@ispace-inc.com>
Instead of hardcoding in linker script, use a Kconfig and deal with
dependencies in Kconfig instead of directly in the linker file.
This patch moves both:
PRIVILEGED_STACK_TEXT_AREA
and
KOBJECT_TEXT_AREA
to arch/Kconfig.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add Kconfig options for Low Power and Deep Sleep States which
need to be selected by the SoC's based on it's supported
Low Power States.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Rather than do that for each architecture, source SoC Kconfigs where the
code is maintained, under ZEPHYR_BASE/soc.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
With the new Kconfig preprocessor (described in
https://github.com/torvalds/linux/blob/master/Documentation/kbuild/
kconfig-macro-language.txt), the syntax for expanding environment
variables is $(FOO) rather than $FOO.
$(FOO) is a general preprocessor variable expansion, which falls back to
environment variables if the variable isn't set (like in Make). It can
also be used in prompts, 'comment's, etc.
The old syntax will probably be supported forever in Kconfiglib for
backwards compatibility, but might as well make it consistent now that
people might start using the preprocessor more.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The prefixes might be a leftover from the old 'option env="..."' symbols
(which are no longer needed). Since environment variables can be
referenced directly now, there's no point in having a prefix.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
