The blobs are now part of nrf_wifi module, and remove the manual check
and add verifying the blobs and their integrity using helper function.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The shim files should be part of the Zephyr module directory within
Zephyr, as they are coupled with the module implementation which os OS
agnostic.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Following the naming convention add an underscore and update path in the
maintainers file too.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Do not enable the video sw generator if a real camera is present. This
helps to save some spaces and to avoid unrelated code going
into the built image.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Most likely there is no point of synchronizing RTC if net core is
not enabled. Same for the bootloader.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Replacing "area: Networking" with "area: PTP" to prevent from
including myself in issues and PRs that are related to every
piece of Networking code. Insted I'll be included only in PTP
related issued/PRs.
Signed-off-by: Adam Wojasinski <awojasinski@baylibre.com>
Enable BLE feature for Nucleo-WB09KE and Nucleo-WB05KZ.
Dedicate 32KB and 8KB at the end of flash memory to storage partition on
Nucleo-WB09KE and Nucleo-WB05KZ respectively.
Add ble tag to the both devices yaml file.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Put the default value for BT_AUTO_PHY_UPDATE and BT_AUTO_DATA_LEN_UPDATE
to "n" at SOC level since they cause "controller busy" due to starting
several parallel BLE procedures during connection by
"perform_auto_initiated_procedures" function. At the moment, ST controller
does not support parallelism, i.e. host should not initiate a new procedure
before previous one is completed.
Disable CONFIG_BT_HCI_ACL_FLOW_CONTROL at SOC level.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Add Bluetooth HCI driver for STM32WB0x series.
Modify CMakeLists.txt to compile the driver based on its kconfig parameter.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
This PR adds arduino giga r1 overlay in the dac sample.
Arduino Giga R1 has a 3.5mm audio jack connected to the
dac.
Signed-off-by: Mario Paja <mariopaja@hotmail.com>
allows use of touch_sensor, rtc_counter, and wdt simultaneously by enabling
ESP_INTR_FLAG_SHARED when calling esp_intr_alloc()
Signed-off-by: Marcio Ribeiro <marcio.ribeiro@espressif.com>
The `Kconfig.defconfig` is not good place for put `select PINCTRL`.
Drop `select PINCTL` from `Kconfig.defconfig` and add it at each
driver's Kconfig.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
A warning could be generated when compiling with -Wtype-limits. This
works around the warning which could happen if initial_count is 0 and
count_limit is K_SEM_MAX_LIMIT.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The function does not return the language, but rather stores
the lang in the provided lang param.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
bt_conn_le_create logs a warning if the provided conn is
non-NULL which was the case here. Simply set it to
NULL as it is a local variable.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Optionally write to ad559x register bit which increases DAC output range
from 0V to 2 x Vref.
The functionality has been tested on AD5593r.
The voltage at 4095 has been measured to 5.01 volts.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The `default y`, which is coupled with
`depends on DT_HAS_WOLFSON_WM8904_ENABLED` to link the settings with
DeviceTree, which was missing, so I added it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add a new west command as helper for package management of Zephyr
and modules.
The first package manager to get supported is pip, where west projects
can list individual packages or requirements files in their module file.
A convenience --install argument is added to install the packages instead.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
