Both threads, 4 and the ztest_thread (test_thread_join) where
joining thread5. If thread 4 is scheduled before the
main thread it will be dead before the main thread
had chance to join it. Just changed thread 4 priority to ensure that
this problem does not happen.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The cached device pointer must be placed in memory that allows user
mode invocation of the test functions to access it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Refactor use of 16-bit common GATT UUID types where a complete UUID
object is declared on the stack only to use the 16-bit value.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When converting ELF to a flashable image, the esptool can only
process up to 16 ELF sections. Zephyr has been happily grouping
similar objects into linker sections which can easily go over
esptool's limit. This patch consolidates the kernel, net, log,
and shell objects into their own sections.
Also remove the app_noinit section as no one is emitting
anything into that section, and it's not being used by other
arch/SoC/boards in Zephyr.
Fixes#20980
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v1.03.
Requires https://github.com/zephyrproject-rtos/hal_st/pull/5
(merged as b52fdbf4b62439be9fab9bb4bae9690a42d2fb14)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The interrupt enabling routine was called before the
chip enabling routine resulting in a runtime failure
when triggers are set.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The Cypress cy8ckit_062_wifi_bt kit is splitted on two directories.
There is no reason to keep it separated. This squash M4 and M0 boards
as one board file.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Reduce the size of the disconnect pool required the full MTU
for a disconnect request.
Also completely remove the pool when not needed.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
If we run with --cmake-only we get the following:
`ERROR - Unknown status None`
Fix this by treating no status set as "passed" for the --cmake-only
case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctrl-0 property for CAN nodes and remove pinmux.c.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Martin Jäger <martin@libre.solar>
OSDP secure channel require a truly random number generator
source. Make this dependency explicit.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Fix the missing return statement when Auxiliary PDU
transmission is aborted because Primary PDU does not have
the aux pointer setup. Also, directly stop clocks and
post LLL done, like being done in other state/role LLL.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Minor Extended Advertising conditional compilation reorder
to better reflect the order Observer->Extended Scanning
dependency.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
NODE_RX_TYPE_EXT_ADV_TERMINATE is generated in ULL context
and shall not increment received PDU quota value.
Fixes#29101.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
It's great to have full manifest examples that can actually work as they
are, however the number of lines can "dilute" the feature currently
described and distract from it. Add some comments in the manifests to
highlight the current topic(s).
The file tree examples and their descriptions are carefully made up and
generally excellent, however I found my eyes going constantly back and
forth between the two in order to match them with one another and build
the actual, graphical representation in my head. These new comments
attached to the major elements of the trees will IMHO accelerate that
visual representation. What I found especially lacking: clues about
which directories are .git/ clones; a pity in the pages specifically
about git clone organization.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
This CL fixed the wrong comparison during searching the vw signal
that issued interrupt from MIWU in espi_vw_generic_isr().
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The WGM160P module combines the WF200 Wi-Fi transceiver with
an EFM32GG11 MCU
This code is based on the efm32gg_stk3701a board definitions
Signed-off-by: Thorvald Natvig <thorvald@natvig.com>
Setup the stack as early as possible to catch any possible errors in the
reset routine and handle also EL3 fatal errors.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The content of the SCR_EL3 register is overwritten by a later
instruction. Also no need to route SError, IRQs and FIQs to EL3.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Use the new DT facilities to configure DAC pinmux on all STM32 nucleo
boards currently supporting the DAC.
Signed-off-by: Martin Jäger <martin@libre.solar>
The nrf52 bsim hw models now require some of these to
be defined. For this case we cannot implement these
as static inline functions as that would redefinitions
of the functions.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
A normal websocket close sequence:
close(websock) ->
websocket_close_vmeth() ->
websocket_disconnect()
close(ctx->sock) called in the function websocket_disconnect()
and cause websocket_close_vmeth() called again.
Finally stack overflow by loop close call.
It's maybe a side-effect by PR #27485
Signed-off-by: Jackie Ja <qazq.jackie@gmail.com>
The existing calculation of the BULK_EP size can sometimes result in a
bulk EP size that is not spec-compliant. The accepted BULK_EP sizes are
8, 16, 32 or 64 bytes.
Additionally, the INT_EP size is always set to the max EP size since
BT_BUF_RX_SIZE is always greater than that (min. 73 in Kconfig).
This commit sets the BULK and INT endpoint sizes to their maximum
supported values.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
In PR #26836, we switch nSIM from custom legacy ARC UART model
to ns16550 model, which will allow us to use zephyr images build for
nSIM on other platforms like HAPS, QEMU, etc...
In PR #27334, which introduce new board nsim_em7d_v22, has gone
parallel to the switch to dwuart, and is still using legacy model.
With wrong configuration, the uart for nsim_em7d_v22 has no output,
which cause all tests failure.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
The legacy macros were first deprecated in Zephyr v2.3. Now that
Zephyr v2.4 has been released, that makes two releases where these
macros have been deprecated, so it's OK to remove them.
This leaves support for legacy binding syntax in place. Removing that
is left to future work.
We need to update various pieces of documentation related to flash
partitions that never got updated when the new API was introduced.
Consolidate this information in the flash_map.h API reference page,
since that's really where users will run into it. This also gives us
the opportunity to improve this documentation.
Adjust a couple of kconfigfunctions.py and sanitycheck bits to use
non-legacy edtlib APIs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
BOSSA takes the offset within flash memory, not the absolute address.
This doesn't matter on most boards as the flash starts at zero but
does matter on the Due as the flash starts at +512 KiB.
Signed-off-by: Michael Hope <mlhx@google.com>
Port minor anchor point synchronization drift implementation
changes.
Relates to changes in commit 732de50f67 ("Bluetooth:
controller: Refactor out drift compensation code").
Fixes#29062.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In order to be in line with other DT_INST macros in zephyr code base,
swap the arguments order in following macro definitions:
*ST_STM32_DT_PINCTRL
*ST_STM32_DT_INST_PINCTRL
Update the users accordingly.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to pcintrl configuration using pcintrl helper
macros.
Pinctrl init sequence has to be done before bus_mutex initialization.
Driver dts bindings are updated to reflect usage of pinctrl-x
properties
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
As an alternative to ST_STM32_DT_INST_PINCTRL, provide
ST_STM32_DT_PINCTRL macro and set of matching internal macros.
This could be used by device drivers that can't use directly
device instances but rather the node label identifier. For instance:
ST_STM32_DT_PINCTRL(0, i2c1);
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Current set of helpers provided for STM32 pinctrl devicetree are
using device instance as input.
In order to prepare for next version that will take node identifier
as input, change existing set of macros using _INST_ namespace.
Additionally rename NODE_ID_FROM_PINCTRL to
ST_STM32_DT_INST_NODE_ID_FROM_PINCTRL.
Finally update existing macros users to this new name scheme.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
