The different boards with stm32 which have node enabled in their DTS
also requires the HSI48 clock to be enabled.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
-Enable the die-temp capabilities of ADC in each dts file of stm32
boards where it is available.
-Execute the testcase running the samples/sensor/stm32_temp_sensor on each
available target board.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
Add alias to boards with watchdog enabled to facilitate the
move of samples/drivers/watchdog to use DT_ALIAS.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
The goal of this commit is to update existing STM32 boards descriptions
to use these size "DT_SIZE" macros to enhance readability. To realize this
i used a python script, which will detect the STM32 Boards
/zephyr/board/arm, and then will update in the dts files the partition
description using "DT_SIZE_K" and "DT_SIZE_M" macros.
Check manually and modify in .overlay files in samples and tests.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
Most LEDs had 0 or 4 nanoseconds set as a period, a value that doesn't
make sense for a PWM signal driving an LED. A period of 20ms (50Hz) is a
frequently used value as it is above the flicker fusion threshold. All
STM32 based boards have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add the pinctrl state name (default) for the PWM peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the CAN peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the I2C peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the ADC peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the UART/USART/LPUART
peripherals. Changes performed using the following Python script run
from the repository root:
```
from pathlib import Path
import re
for fpath in Path(".").glob("boards/arm/**/*.dts"):
lines = open(fpath).readlines()
is_stm32 = False
for line in lines:
if "stm32" in line:
is_stm32 = True
break
if not is_stm32:
continue
with open(fpath, "w") as f:
for line in lines:
f.write(line)
m = re.match(r"(\s+)pinctrl-0.*us?art.*", line)
if m:
f.write(m.group(1) + "pinctrl-names = \"default\";\n")
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Prescaler was misplaced in pwm binding, instead of timers binding.
For example, TIM6/TIM7 doesn't have PWM capability,
but have a prescaler.
This change also prepares the introduction of timer based counter
(which requires prescaler at timer level)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
USB devicetree nodes in Zephyr have different names,
mostly derived from the designations in data sheets.
Add zephyr_udc0 (USB device controller) nodelabel to
specific USB node to allow generic USB sample to be build.
Follow up on commit b4242a8 ("boards: add USB node aliases")
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Defines partitions that can be used by mcuboot on nucleo_h743zi board.
Please note that mcuboot is not yet supported on stm32 h7 family as the
write-block-size is greater than 8.
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Defines partitions that can be used by mcuboot on nucleo_h743zi board.
Please note that mcuboot is not yet supported on stm32 h7 family as the
write-block-size is greater than 8.
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Update PWM pinctrl signal names of all non-F1 STM32 boards.
`pwm` variant is not available anymore on non-F1 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Use the new DT facilities to configure ADC pinmux on all boards with
STM32 MCUs currently supporting the ADC.
Signed-off-by: Martin Jäger <martin@libre.solar>
Add support for the polarity flag in the STM32 PWM driver.
STM32 boards using PWM have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Enables PWM support using the built-in red LED. Tested with:
- samples/basic/blink_led
- samples/basic/fade_led
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Only basic support has been added as some drivers require some fixes.
I have successfully tested the following examples:
- samples/hello_world
- samples/basic/blinky
- samples/basic/button
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
