Modify the BT_UUID_XX_ENCODE and BT_LE_SUPP_FEAT_XX_ENCODE
macros to use the SYS_ENCODE_LEXX macros, instead of re-inventing
the encoding.
Also apply the macros for several other places.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add a series of macros that can encode a XX-bit value
into array values. This can be used to easily encode
const array data.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
KSGEN and CRYPT tasks and corresponding events weren't compiled
for boards with nRF51 SoCs due to change in HAL.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
- Add doxygen group and improve documentation for bbram.h
- Add a bbram section under peripherals in the main doc/ directory
Fixes#55257
Signed-off-by: Yuval Peress <peress@google.com>
Modify UseTab to use ForContinuationAndIndentation instead
of always. This will only use tabs for indentation, and then
spaces for alignment, which is the most commonly used approach
in Zephyr.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The function bt_codec_cfg_get_chan_allocation_val takes a pointer
to an enum, rather than an uint32_t, but was wrongly defined in
the header files and incorrectly used a few places.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The generic BT shell header, bt.h, contained quite a few things
related to audio, which should be put in the audio.h shell header
file.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Word size setting limited any SPI transaction to the frame
size. In addition to making the SPI inefficient this
broke drivers that set the word size. It appears that most
drivers use a one byte (8) size for this setting.
This change respects what I think is the intended use of
the word size setting. That is to set the length of
each element in a tx/rx buffer struct.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
Allow defining multiple instances of enc28j60.
Remove the ETH_ENC28J60_0 Kconfig option along with this.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Following the change that replaces ETH_ENC28J60_0_FULL_DUPLEX
by devicetree property.
Enable enc28j60's `full-duplex` explicitly in the overlay file.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Following the change that replaces ETH_ENC28J60_0_FULL_DUPLEX
by devicetree property.
Enable `full-duplex` explicitly in overlay files.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add the `full-duplex` property for the `microchip,enc28j60` node.
Replace ETH_ENC28J60_0_FULL_DUPLEX Kconfig option with this property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
This patch adds MULTITHREADING as a dependency to the nrfx i2c driver.
The driver uses semaphores internally and can result in linker errors
if MULTITHREADING is not enabled.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Updated the code to to invoke reset using PCR block
z_mchp_xec_pcr_periph_reset() instead of resetting
using I2C Configuration register
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Do not enable SOF event interrupt when the USB device driver is going to
discard the event anyway. This prevents completely unnecessary interrupt
handler from executing 1000 times a second when device is connected.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Test script clean up related to common code moved in
commit add1397e4a ("tests/bsim/bluetooth: Tests scripts
refactor").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add BabbleSim test to verify creation of peripheral multiple
CIS in a CIG, connect ACL to one peripherals and create nine
CIS to that peripheral device.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Updated nRF5 Series LLL implementation to support multiple
peripheral CIS establishment from peer central devices.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add BabbleSim test to verify creation of Central multiple
CIS in a CIG, connect ACL to three peripherals in a group
in the timeline and create CIS to each peripheral.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Central multiple CIS create implementation using advanced
scheduling to find the active CIG events and calculate the
CIS offset to be used in the LL_CIS_REQ PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add BabbleSim test to verify creation of Central multiple
CIS in a CIG, connect ACL to nine peripherals and create
CIS to each peripheral.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use accumulated connected ISO LLL prepare callback latencies
to check supervision timeout.
Also use the accumulated connected ISO LLL prepare callback
latencies to adjust SN and NESN values.
Connection establishment can cause short prepare callbacks
inserted before Connected ISO group prepare callbacks, that
cause the Connected ISO group prepare callbacks being
cancelled while being in prepare pipeline. Hence, it is
necessary to accumulate prepare callback latencies wherein
ticker callbacks are executed but prepare callbacks are
cancelled in the prepare pipeline.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implementation of preliminary Central with multiple CIS
create support in Lower Link Layer. Uses a simple CIS
offset calculation that works when ACL are created with
connection interval that is multiple of CIG ISO interval.
Each ACLs are offset using BT_CTLR_CENTRAL_SPACING hence
having the same CIG sync delay values for all the ACLs.
Advanced Scheduling to setup CIS in any order of ACL and
CIS combination, ACL placed anywhere in timeline and CIS
creation will come therein will be implemented in later
Pull Requests.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Include ticker expire remainder value when calculating the
cis_offset to acheive fine timing in scheduling the CIG
radio events relative to its associated ACL radio events.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use the ticker_start_us() interface for Central and Central
ISO setup to acheive fine timing for the first expire
timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To acheive microsecond or fine timing for first expire
timeout, pass remainder value of the coarse tick to a new
ticker_start_us() interface. The new interface is available
with BT_TICKER_EXT feature enabled.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix implementation of CIS Null PDU Indicator use to meet the
BT Specification statement, that, if the source of the data
fails to provide a payload in time for a CIS subevent, then
the link layer shall transmit a CIS Null PDU instead.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This is re-introduction of Extended, Periodic Advertising
and Broadcast ISO using ticker expire info feature to get
the aux, sync and BIG offsets.
Relates to commit 714d74b77b ("Bluetooth: controller: Use
new ticker feature to get offsets").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Ticker remainder and lazy get depends on match get interface
provided by BT_TICKER_NEXT_SLOT_GET_MATCH.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove redundant range and default for BT_CTLR_ADV_AUX_SET
when supporting BT_CTLR_ADV_PERIODIC.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
BT_TICKER_EXT is not supported with BT_TICKER_LOW_LAT.
Remove redundant select of BT_TICKER_EXT for
BT_CTLR_ADV_EXT.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When debugging devicetree related issues, it may be useful to turn macro
expansion tracking off. Let's document this in the troubleshooting
section.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a new compiler option to control tracking locations of tokens across
macro expansions. It may be useful to disable it when debugging long
macro expansion chains.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Improve the radio off code, mainly:
- Compile the file only if necessary, ie, LORA radio not in use
- Use pin information from DT, so that we do not need to hardcode pins
and can switch to dt-spec APIs.
- Improve error handling, includes, etc.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The SERCOM4 is hardwired to PB30/31, PC18/19 internally for the LoRa
radio. Move the pinctrl entries to SoC dts level. The same applies for
samr35.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In general, peripherals should be disabled by default and enabled at
board level when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
