The lis2dw12 sensor can generate the TAP interrupt only on INT1,
while DRDY can be generated on both. The int-pin DT property
specifiy on which pin the DRDY (and not the TAP) can be generated.
This commit fix the way the trigger is set: first the driver checks
the trigger type (DRDY or TAP), then it uses the int-pin information
only in DRDY case but allows setting TAP regardless of int-pin (it
always routes it on INT1).
The previous code was first checking int-pin: if it was INT2 then
the driver refused setting TAP triggers.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit aligns lis2dw12 sensor driver to latest multi
instance sensor driver model.
In particular it makes use of the stmemsc common routines
and move ctx handler inside struct config, so that the
bus_init routines can be totally avoided.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Remove all odr values from Kconfig and always init it
at 12.5Hz. It is responsibility of application to set
the rate to a different value using SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move lis2dw12 trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use gpio_dt_spec structure (and related APIs) in config for configuring
the gpio used for drdy and pulse interrupts.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
When the temperature is lower than 20C, adc_temperature is smaller than
(data->t_ref << 8), which should yield a negative value for dT. While dT
and adc_temperature are correctly declared as signed, the subtrahend is
wrongly casted to unsigned, yielding insanely high temperature values.
Fix that by casting it to int32_t instead of uint32_t.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Convert the various device_get_binding() calls used to get the device
clock node to use DEVICE_DT_GET. The latter is processed at link time,
so it should be a bit more efficient.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Since we are writing a register it makes more sense for the type
to be unsigned. This hopefully address a compile warning we get
with clang:
error: implicit conversion from 'int' to 'int16_t' (aka 'short')
changes value from 32768 to -32768 [-Werror,-Wconstant-conversion]
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If CONFIG_ICM42605_TRIGGER is not set the driver doesn't build. There
are a few places that need ifdefs based on CONFIG_ICM42605_TRIGGER for
the driver to build correctly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add multi-instance support to the MS5607 driver. This is needed to
easily add I2C support later. It also simplifies a bit the driver
initialisation by using more static values.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
axis1bit16 and axis3bit16 unions are no longer used
and can be deleted from all .h files that are referencing
them.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v2.00.
Requires https://github.com/zephyrproject-rtos/hal_st/pull/7
(merged as 575de9d461aa6f430cf62c58a053675377e700f3)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
It is necessary to put the device in standby to change the contents of
CTRL_REG1. This register is used to change the sampling frequency.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The bq274xx fuel gauge does a softreset when configuring, after
which the device is polled and sealed. However the sleep logic
was inverted so the poll became blocking.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
The macros are used to get the pin(s) of a given driver instance. Add
_INST prefix to match convention used by the devicetree.h. The original
macros can now be used to obtain pin(s) of an arbitrary device instance
identified by the nodelabel.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add multi-instance support and make use of the stmemsc i2c/spi
read/write routine that has been introduced to simplify the ST
sensor drivers code.
Moreover, move spi-full-duplex property from Kconfig inside Device
Tree, so that each LIS2MDL instance can be configured selectively
in accordance to how it is used in h/w.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
commit d31ed3be04 enabled multiple
instances but when multiple instances are actually used the code does
not compile
Signed-off-by: Guillaume Lager <g.lager@innoseis.com>
For some reason a few drivers were not converted to the new device PM
callback signature. The reason may be because the device PM part is
compiled only when CONFIG_PM_DEVICE=y, a condition not enabled in CI by
default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The lis2mdl temperature samples work with a level of 25 Celsius.
When temperature goes below that level the samples become negative
and there was an issue in properly propagating the sign.
Fix#35910
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The lps22hh 24 bit raw sample is left aligned, which means that
it needs to be right-shifted by 8 before applying conversion.
Moreover the conversion has been simplified for clarity.
Fix#35871
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use gpio_dt_spec structure and related macros for both drdy
and AnyMotion interrupts, to have a more compat, readable and
safe code. Moreover, skip setting DRDY or AnyMotion trigger
from application if the corresponding irq-gpios has not been set.
(This commit also fixes#34794)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Change the drivers's compatible from atmel,sam-tc to atmel,sam-tc-qdec.
The atmel,sam-tc should be reserved for the future counter driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
(same considerations as commit 2f01479b)
In a multi-instance driver it may happen that on some h/w
one device should use interrupts and a second device should use
polling mode. So, CONFIG_IIS2ICLX_TRIGGER is not enough to discriminmate
if interrupt inizialization routine should be called or not; the choice
is now based whether the "irq-gpios" property is present in the DT
for that particular instance or not.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use gpio_pin_configure_dt() and gpio_pin_interrupt_configure_dt()
for drdy_gpio: they result in a more readable code.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
In case of multi-instance the driver tries to discover whether
there are devices attached to SDx/SCx sensorhub bus. If not it
just turns the shub_inited variable (inside data structure) to false
and skips doing any further sensorhub related action for that
particular IIS2ICLX device instance, regardless the fact that the
macro CONFIG_IIS2ICLC_SENSORHUB is enabled.
Moreover, the info found during the enumeration process for a
particular instance (number and types of attached devices) must be
saved inside the per-instance data structure, so that more than one
IIS2ICLX device can be used as a sensorhub without interfering with
the others.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
In case of multi-instance the driver tries to discover whether
there are devices attached to SDx/SCx sensorhub bus. If not it
just turns the shub_inited variable (inside data structure) to false
and skips doing any further sensorhub related action for that
particular LSM6DSO device instance, regardless the fact that the macro
CONFIG_LSM6DSO_SENSORHUB is enabled.
Moreover, the info found during the enumeration process for a
particular instance (number and types of attached devices) must be
saved inside the per-instance data structure, so that more than one
LSM6DSO device can be used as a sensorhub without interfering with
the others.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use gpio_pin_configure_dt() and gpio_pin_interrupt_configure_dt()
for drdy_gpio: they result in a more readable code.
Moreover, this commit includes also the fix for PR #35156
(i.e. CID 235979, add check for gpio_pin_configure() return val).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
STM32 internal temperature sensor driver.
This sensor can be used to measure the temperature of the CPU
and its surroundings.
Signed-off-by: Eug Krashtan <eug.krashtan@gmail.com>
In a multi-instance driver it may happen that on some h/w
one device should use interrupts and a second device should use
polling mode. So, CONFIG_LSM6DSO_TRIGGER is not enough to discriminmate
if interrupt inizialization routine should be called or not; the choice
is now based whether the "irq-gpios" property is present in the DT
for that particular instance or not.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move ctx structure from struct data to struct config, so that
it can be filled at compile time and we could get rid of the bus
init routines.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The context parameter used across device power management is
actually the power state. Just use it and avoid a lot of
unnecessary casts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
device_pm_control_nop has been marked deprecated so we get a CI
build error due to its use. Replace with NULL to fix the issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The MAX17262 is an ultra-low power fuel-gauge IC which implements the
Maxim ModelGauge m5 algorithm. The IC monitors a single-cell battery
pack and supports internal current sensing for up to 3.1A pulse
current. The IC provides best performance for batteries with 100mAhr
to 6Ahr capacity.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
