Those MCUs have 2KB RAM and 16KB FLASH memory, but they are still
powerful enough to run small configuration of Zephyr RTOS.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added / Tested support for RNG on the STM32F767ZI nucleo board.
Updated the SoC defconfig to auto-enable the driver when
ENTROPY_GENERATOR is enabled, and updated the board README.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
It was not clear that hexdump messages does not support prepending
with function name. Added clarification.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The HPET timer was hard-coded to support only edge triggering
interrupts. This adds the necessary bits to enable level
triggering for the timer.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix compilation regression due to addition of const
qualifier to tx_pwr_lvl parameter of ll_tx_pwr_lvl_set
function. Support for BT_CTLR_TX_PWR_DYNAMIC_CONTROL
needs the tx_pwr_lvl to be updated and returned.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The driver API should be assigned at the time the device is defined.
Assigning in the init function is redundant and prevents moving the
pointer to a immutable driver structure.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update code comments in ringbuffer/src/main.c
modify a testcase to verify the address stored by ring buffer
is contiguous, and the size of every element is equal to the size of
pointer.
Signed-off-by: Ningx Zhao <ningx.zhao@intel.com>
DMA driver shall be initialized before any of its
clients. Right now, its initialization priority is
lower than that of UARTs. So, increase its init
priority to support future async uart drivers.
Signed-off-by: Jun Li <jun.r.li@intel.com>
- Change default CPU Clock to 240MHz
(PLL is activated)
- I2C, UART will use sysclk from clock driver
- esp32_enable_peripheral replaced by
clock_control_on
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
- Support PLL for Higher Frequencies 80,160,240 MHz
- Support XTAL Frequencies 26MHz, 40MHz
- Clock Driver can't be disabled, because all of the other drivers
will depend on it to get their operating Frequency based on chosen
clock source (XTAL/PLL).
- Add needed references to BBPLL i2c bus ROM functions.
- Add `rtc` node to Device Tree.
- Since All Peripherals Frequency is depending on CPU_CLK Source,
`clock-source` property added to CPU node
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
If CONFIG_THREAD_NAME is enabled, we must use log_strdup() when
printing the thread name.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
test_testsuite_class.py: Added testcases for load_From_file and
apply_filters functions of Class Testsuite.
conftest.py: Modified class_testsuite fixture to create the
outdir as temporary directory which gets deleted after execution
of testcases.
test_data/sanitycheck.csv: load_from_file function uses this
customized file to load the failed or last run testcases.
test_data/sanitycheck_keyerror.csv: file used by
test_load_from_file function to raise the appropriate error
if there is a keyerror.
scripts/requirements-build-test.txt: added mock & csv python libraries
Signed-off-by: Aastha Grover <aastha.grover@intel.com>
test_testsuite_class.py: Added testcases for add_configurations(),
get_all_testcases(), get_toolchain() and get_platforms() functions
test_data/board_config: board root directory for all board
configurations. This is also to add the platform configurations
in a list which is used for further testing.
conftest.py: Added fixtures for all_testcases_dict (returns a
dictionary of testcases) and platforms_list (returns a list of
all platforms using add_configurations function).
Signed-off-by: Aastha Grover <aastha.grover@intel.com>
Under Linux when you shutdown a socket which is blocked on
an accept call the error code returned by accept is EINVAL.
Modify the socket code to be inline with this behaviour.
Signed-off-by: Léonard Bise <leonard.bise@gmail.com>
When closing a listening socket the functions waiting on the
FIFO will be unblocked this will result in receiving a NULL child
context. If that is the case return an error instead of carrying on.
Return the same error code (EINVAL) that is returned on Linux when
calling shutdown on a blocked accept call.
Signed-off-by: Léonard Bise <leonard.bise@gmail.com>
In case CoAP packet does not carry payload, and the last option is
zero-length, the option structure was not filled with data (opt number
and length). Fix the length check to prevent this from happening.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This should be boolean according to specification. It makes difference
when JSON encoding is used.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Allow passing the channel as a number instead of a string in order to
support sensor-specific channels (channel SENSOR_CHAN_PRIV_START and
up).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Enable VLAN support so that this driver can be used to test
the VLAN when using qemu_x86 board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This change removes references to raw POSIX types and functions,
allowing the drivers to build without NET_SOCKETS_POSIX_NAMES.
After this, the dependency between NET_SOCKETS_OFFLOAD and
NET_SOCKETS_POSIX_NAMES can be removed.
See issue #26033 for additional context
Signed-off-by: Adam Porter <porter.adam@gmail.com>
The driver currently blindly copies all of the outgoing bytes into the
endpoint. Instead, calculate the endpoint size and copy up to that
amount instead.
Signed-off-by: Michael Hope <mlhx@google.com>
Sets thread names for all usb device class threads (bluetooth, bt_h4,
mass storage, and rndis) to aid debug.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch introduces the support of low power modes
for the STM32L4xx from STMicroelectronics based on the lptim
Here, the power modes are sleep modes with lptimer as wakeup.
Depending on the SYS_POWER_MANAGEMENT configuration.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
A non-blocking, isr-safe version of get_entropy() is necessary in order
to be called during boot time before POST_KERNEL initialization.
Otherwise a crash is seen as the existing get_entropy() implementation
uses k_sem and relies on interrupts.
Fixes#18629
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Introduce new test for eventfd, which will test it in only basic
scope. The real reason why this is introduced is to have a test with
minimal set of configuration dependencies, such as disabled
pthreads (compared to full tests/posix/eventfd/ variant). This allows to
test eventfd mechanism with both POSIX_API=n and POSIX_API=y.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The test takes ~175s to end on nrf5284dk_nrf52840 and was failing
due to too short default timeout (60s).
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
Avoid null pointer access by checking that Ethernet device has
PTP clock before trying to get the actual PTP clock device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to follow threads by name in the debug output,
output a thread name if CONFIG_THREAD_NAME is enabled.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
So far net config initialization code relied on number of services
needed by application. This was fine as long as all enabled
services (e.g. CONFIG_NET_IPV4=y, CONFIG_NET_IPV6=y) were selected by
project configuration as "needed" (e.g. CONFIG_NET_CONFIG_NEED_IPV4=y,
CONFIG_NET_CONFIG_NEED_IPV6=y). Problem appeared for example when both
IPv4 and IPv6 were enabled (CONFIG_NET_IPV4=y, CONFIG_NET_IPV6=y), but
only IPv6 was marked as "needed" (CONFIG_NET_CONFIG_NEED_IPV6=y). In
such situation number of required services was equal to 1. When IPv4
setup was completed, this resulted in returning from net_config_init()
function. Application code failed, because IPv6 was still not
functional.
Do not rely on number of services anymore, as it is error prone. Use
flags instead to mark which services are ready. Compare those flags with
the flags passed to net_config_init() (selected in project configuration
in most cases) to decide whether network configuration has completed
already or not.
Also introduce services_notify_ready() and services_are_ready() helper
functions to isolate implementation details from the logic.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
With current design there is single semaphore (called 'waiter') for
wakeing up initialization thread. This thread should then check for
number of protocols that still need to be initialized. This happens now
only when waiting on 'waiter' semaphore times out.
Do not check for k_sem_take(&waiter) return value, as all needed
information about protocols being initialized already is in 'counter'
semaphore.
Fixes: #25358
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Unit test code requires IPv6 to be ready. Select
CONFIG_NET_CONFIG_NEED_IPV6=y to ensure that.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Unit test code requires IPv6 to be ready. Select
CONFIG_NET_CONFIG_NEED_IPV6=y to ensure that.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
