Add `DT_ANY_INST_HAS_BOOL_STATUS_OKAY` as a complement to
`DT_ANY_INST_HAS_PROP_STATUS_OKAY`. This macro exists because boolean
properties not present on a node are still generated with a value of 0,
and therefore cannot be used with `DT_ANY_INST_HAS_PROP_STATUS_OKAY`.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The mechanism for communication between domains requires
extra threads. So change the default value MAX_THREAD_BYTES
to allow usage of more threads.
Signed-off-by: Georgios Vasilakis <georgios.vasilakis@nordicsemi.no>
The commit removes flash_area_open usage from tests, where it is not tested
and only used to obtain area.
The commit adds tests for flash_area_device_is_ready.
The commit adds test for flash_area_sectors, which is equivalent
of flash_area_get_sectors but takes flash area object instead of flash
area index.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit adds flash_area_sectors function that allows to get information
on sector/erase page layout by flash_area object pointer instead of
index.
The only difference between flash_area_sectors and flash_area_get_sectors
is that the later calls flash_area_open internally and as such requires
flash map to be compiled in.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit adds FIXED_PARTITION(label) macro that allows to obtain
struct flash_area object for partition of given label.
The macro allows instantiation of partition at point of usage
and will be replacing need for defining flash map with all partition
entries.
Area obtained with the macro should not be passed to open, instead
flash_area_device_is_ready, basically equivalent of device_is_ready
should be called on the obtained pointer to check if area is ready
for use.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Removes legacy configuration options. The same coverage is provided by
existing PSA_WANT_... selects.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Introduced few Kconfigs that allow to change default values
of MLE child timeout and child supervision timeouts.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Similar to `stm32_ltdc_display_blanking_off()`, use local device variable
instead of accessing the config's structure member again.
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Change `GPIO39` to `GPIO38` in overlay.
The esp32s3_devkitc rgb led is connected to GPIO38, not 39.
Tested change on board and verified to function as intended.
Signed-off-by: david burke <david@aheng.io>
Make sure that `MBEDTLS_PSA_ITS_FILE_C` is not defined when
`CONFIG_SECURE_STORAGE` is enabled as the former takes precedence over
the latter in Mbed TLS (`psa_crypto_storage.c`).
This fixes usage of the secure storage subsystem by Mbed TLS on platforms
such as `native_sim`.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Allow configuring the clock prescaler divider for the NXP Kinetis
Timer/PWM Module (TPM). Setting the prescaler to a lower value
allows for higher resolution for the generated PWM waveforms.
This change is inspired from the pwm_mcux_ftm driver:
Link: https://github.com/zephyrproject-rtos/zephyr/pull/25396
Signed-off-by: Maximilian Werner <maximilian.werner96@gmail.com>
This is line is breaking in some CI setups since the recent ruff fixup
with:
ModuleNotFoundError: No module named 'domains'
Try and fixit by explicitly adding the path before the include, all
other instances have it already.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Enumerate explicitly on which SoC's DMA_INTEL_ADSP_HDA_TIMING_L1_EXIT
should be set by default. For new platforms in the ACE series, the
default should be disabled.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Endpoint disable function is racing against bus traffic. If the bus
traffic leads to transfer completion immediately before the endpoint
disable is executed, then the transfer complete interrupt will remain
set when the endpoint is disabled. For OUT endpoints this leads to "No
buffer for ep" errors, while for IN endpoint this can lead to double
buffer pull which causes assertion failure.
The proper solution would be to change endpoint disable to not actually
wait for the individual events (and accept that the endpoint may not
need to be disabled because the transfer can just finish). For the time
being workaround the issue by clearing XferCompl bit on endpoint
disable.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Application is expected to call usbd_uac2_send() on each enabled USB
Streaming Output Terminal (isochronous IN data endpoint) exactly once
every SOF. The class is bookkeeping queued transfers to make it easier
to determine component at fault when things go wrong. However, this
approach only works fine if the underlying USB device controller buffers
the data to be sent on next SOF and reports the transfer completion
immediately after data is buffered (e.g. nRF52 USBD).
While DWC2 otg also requires the SW to arm endpoint with data for the
next SOF, unlike nRF52 USBD the transfer is only considered complete
after either the IN token for isochronous endpoint is received or after
the Periodic Frame Interval elapses without IN token. This design
inevitably requires the application to be able to have at least two
buffers for isochronous IN endpoints.
Support dual buffering on IN data endpoints to facilitate sending
isochronous IN data on every SOF regardless of the underlying USB device
controller design.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
When handling incomplete iso IN interrupt mark current transfer as
complete and program the endpoint with any subsequently queued packet.
Program the endpoint directly in interrupt handler because the data
must be programmed before SOF (by the time incomplete iso IN interrupt
is raised there is less than 20% * 125 us = 25 us before SOF).
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
The NAKSts bit may be set on isochronous OUT endpoints when incomplete
ISO OUT interrupt is raised. The code would then assume that endpoint is
already disabled and would not perform the endpoint disable procedure.
This in turn was essentially halting any transmission on the isochronous
endpoint, abruptly terminating the data stream.
Fix the issue by always following full endpoint disable procedure on
isochronous endpoints.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Fixes a wrong placement of a Kconfig which was put into the
wrong file and was bleeding through to every board
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add myself to the ARC collaborators list, as I'm currently employed
by Synopsys to work on improving ARC support in Zephyr.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
This reverts commit 3d3ffa2c05.
The original commit aimed to prevent NULL pointer accesses by moving the
MMU mapping starting point one page later. However, this change has
caused a regression on PTL. Our DSP has registers with addresses lower
than 0x1000, and the firmware uses addresses starting from 0xC40. For
instance, the HDAMLDMICL register is located at 0xCC0, which is now
inaccessible due to the change.
Reverting this commit restores access to these critical registers and
resolves the regression issue.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
- Remove @julius-barendt as collaborator and code owner for areas
related to SPARC and LEON.
- Add myself to the same areas.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Fix the out of bound buffer read by checking the lower-bound index
in the ov5640_enum_frmival function.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
This reverts commit 26614832f2.
A bug in upstream nanopb, which this commit was pulling as part
of the submanifest update, seems to be causing test failures
on big-endian platforms.
Upstream bug: https://github.com/nanopb/nanopb/issues/1039
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Or more precisely, do not remove the workaround for them.
The current HW models are accurate enough in this area for the
workaround to work properly.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
