This is a follow-up to commits e15bdaa1bd
and 07bf22cc94.
The above two commits added some enumerated gain values and those
are not currently handled by the inverting function. Add the missing
entries to the conversion array in the function.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
List of the changes:
* add info about ARCv3 32bit HS5x which support has been
upstreamed recently
* mark HS6x MWDT toolchain support as Y
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
The following modules contain code that include Zephyr headers:
- fatfs
- littlefs
- hal_espressif
They have all been update with the <zephyr/...> include prefix.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The drive-mode property is nRF specific, so prefix it with `nordic,`,
same as the `nordic,invert` property.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
NXP i.MXRT11xx devices have up to 202 dma slots(peripheral dma requests).
Extended dma_slot to 8-bits to support more dma requests.
Signed-off-by: Chay Guo <changyi.guo@nxp.com>
Add LTDC config and pinctrl in board DTS
Modify defconfig so KSCAN and MEMC drivers are enabled if
display is enabled
Update board doc and yaml
Signed-off-by: Tomislav Milkovic <tomislav.milkovic95@gmail.com>
Refactor help text for TFM_FLASH_MERGED_BINARY to use the standard
indentation of tab plus 2 spaces.
Reword BUILD_WITH_TFM default comment, TF-M is enabled by default, not
forced enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Enabling an eSPI channel (r.g. Peripheral Channel, Virtual Wire Channel,
etc.) during an eSPI transaction might (with low probability) cause the
eSPI_SIF module to transition to a wrong state and therefore response
with FATAL_ERROR on an incoming transaction.
This CL workarounds this issue by clearing the bit 4 of NPCX eSPI
specific register#2.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
A missing semicolon caused compiler errors when more than one emulated
gpio device was defined in the device tree.
Signed-off-by: Jan Peters <peters@kt-elektronik.de>
Add support for an alternate clock. If available,
alternate clock is enabled and used to get the
device clock rate.
Based on: #45053.
Signed-off-by: Artur Lipowski <Artur.Lipowski@hidglobal.com>
Previously, the uart_stm32 driver was extended in #44487 to support
swapping the tx and rx pins of supported STM32 UART peripherals.
However, the original change applied this configuration during the
call to the uart_stm32_configure() function. This has now been added to
the uart_stm32_init() function to ensure this behavior on startup for
ports like the virtual com port.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Adds information on adding the image header details to the img mgmt
callback for application-level determination of what to allow or
decline.
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
This allows an application to inspect a mcumgr img upload command to
provide additional information for acceptance or rejection of it, and
makes the previous private version compare function public so that
application code can call it.
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
Enable ZTEST_DO_THE_SHUFFLE to shuffle the order tests are ran.
Additional configs ZTEST_DO_THE_SHUFFLE_SUITE_REPEAT_COUNT
ZTEST_DO_THE_SHUFFLE_TEST_REPEAT_COUNT specify the number of times
the test or suite is executed.
Signed-off-by: Al Semjonovs <asemjonovs@google.com>
Adds the file read/write request hook that applications can use to allow
or decline requests to files to the release notes.
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
Adds details about the file read/write request hook that applications
can use to allow or decline requests to files.
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
This allows an application to inspect a mcumgr file access command and
either allow it or deny it with a result code.
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
The hardware map feature can be used with serial pty mode in
this change. And also add an runner_params option for passing
more parameters from hardware map file to west runner. Note
that you need to create this map file manually because it
cannot be scanned out correctly due to pty is not a physical
HW device existing in system.
And also update doc/develop/test/twister.rst for the usage.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
After introducing SO_SNDBUF socket option, a possible deadlock situation
slipped into the TCP implementation. The scenario for the deadlock:
* application thread tries to send some data, it enters
net_context_send() which locks the context mutex,
* internal context_sendto() blocks on a TX packet allocation, if the
TX pool is empty rescheduling takes place,
* now, if at the same time some incoming packet has arrived (ACK for
example), TCP stack enters tcp_in() function from a different
thread. The function locks the TCP connection mutex, and tries to
obtain the SNDBUF option value. net_context_get_option() tries to
lock the context mutex, but it is already held by the transmitting
thread, so the receiver thread blocks
* when TX packet is available again, the transmitting thread unblocks
and tries to pass the packet down to TCP stack. net_tcp_queue_data()
is called which attempts to lock the TCP connection mutex, but it is
already held by the receiving thread. Both threads are in a deadlock
now with no chance to recover.
Fix this, by obtaining the SNDBUF option value in tcp_in() before
locking the TCP connection mutex.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Thread network makes no use of Solicited-node multicast addresses,
thereby do no create them on the interface to save multicast address
entries for important ones.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
There is a risk of deadlock in case net_if APIs are used from within
net_mgmt handlers as both module APIs are protected with their own
mutexes.
The scenario observed with OpenThread happend when
NET_EVENT_IPV6_ADDR_ADD/NET_EVENT_IPV6_MADDR_ADD events were processed.
The net_mgmt mutex is locked when both, an event handler is being
processed (from a separate net_mgmt thread) and when an event is raised
(for example when a new address is added on an interface). In case a
net_mgmt handler tried to use some mutex-protected net_if API, we could
end up in a deadlock situation - the net_mgmt would wait for the net_if
mutex to release, while some other thread (in this case main during
initialization) could wait within some net_if function, pending on
net_mgmt mutex to be released to notify the event.
Fix this, by preventing net_if APIs from being used from within OT
net_mgmt handlers.
Additionally, simplify the net_mgmt handlers logic, by making use of
additional info provided with an event. Instead of blindy assuming that
recently added address was the last on the list (which might not always
be the case, if addresses are added/removed dynamically), read the
actual address being added from the net_mgmt_event_callback structure.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Since the recent OpenThread update, OT needs more stack to initialize,
therefore bump the stack size in samples using OpenThread.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Inform about the new Zephyr include prefix, mention compatibility
Kconfig option and migration script.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
All includes are now prefixed with <zephyr/...>, even though the old
include paths can still be used when CONFIG_LEGACY_INCLUDE_PATH=y, an
option still enabled by default. Migrating large projects can be tedious
and time consuming. This patch provides a script that can be used to
migrate any Zephyr-based project to the new include path. It is used
like this:
python $ZEPHYR_BASE/scripts/utils/migrate_includes.py \
-p path/to/zephyr-based-project
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactors invalid switch into if statement.
Fixes orientation set return value for normal
display orientation.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Make sure cxcprs isn't zero, or we will have
divide-by-zero on calculating actual_freq.
Test:
1.tests/drivers/pwm/pwm_api pattern
2.GPA0(pwm0) output 79201Hz, 324Hz, 100Hz, 1Hz waveform
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
The overlay was accidentally pushed as part of another commit while
doing some pinctrl/pwm tests.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This is the same fix as the one introduced in 49520eea57 ("samples: nrf:
system_off: Fix force state usage") for nRF boards. Quoting original
commit:
The sample cannot spin in an infinity loop because the idle thread
will not run and consequently the forced state will not be used.
Without this fix, the system doesn't enter SOFT_OFF state:
*** Booting Zephyr OS build zephyr-v3.0.0-3495-ga456c5274614 ***
cc1352r1_launchxl system off demo
Busy-wait 5 s
Sleep 2000 us (IDLE)
Sleep 3 s (STANDBY)
Entering system off (SHUTDOWN); press BUTTON1 to restart
ERROR: System off failed
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for enabling/disabling CAN-FD frame transmission/reception at
run-time.
Fixes: #45303
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert the can_mode enum to a bit field to prepare for future extensions
(CAN-FD mode, transmitter delay compensation, one-shot mode, 3-samples
mode, ...).
Rename the existing modes:
- CAN_NORMAL_MODE -> CAN_MODE_NORMAL
- CAN_SILENT_MODE -> CAN_MODE_LISTENONLY
- CAN_LOOPBACK_MODE -> CAN_MODE_LOOPBACK
These mode names align with the Linux naming for CAN control modes.
The old CAN_SILENT_LOOPBACK_MODE can be set with the bitmask
(CAN_MODE_LISTENONLY | CAN_MODE_LOOPBACK).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Always define the CAN-FD related syscalls but only define the
syscall implementations when CONFIG_CAN_FD_MODE is enabled.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the CAN data phase API functions to timing_data_* for consistency:
- can_get_timing_min_data() -> can_get_timing_data_min()
- can_get_timing_max_data() -> can_get_timing_data_max()
- .timing_min_data -> timing_data_min
- .timing_max_data -> timing_data_max
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Removes label and compatible properties
from the flash section. The properties are
provided by included stm32h723.dtsi.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Removes label and compatible properties
from the flash section. The properties are
provided by included stm32h723.dtsi.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
