remove existing SDMMC SPI driver, since it is replaced by the SPI mode
SD host controller driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
switch all in tree usage of zephyr,mmc-spi-slot to zephyr,sdhc-spi-slot.
This will change all boards to use the new SD subsystem instead of the
SDMMC SPI driver
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
with the legacy USDHC driver fully removed from the tree, the
nxp,imx-usdhc binding can now be used for the new SD host controller
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
all in tree SOCs with the USDHC peripheral have now been converted to
use the new SD host controller USDHC driver, so remove legacy NXP disk
USDHC driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
added support for NXP iMX RT600/RT500 to use to SDHC driver, with SD
subsystem. Tested with RT685 EVK
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SDHC driver implementing spi mode support for SD cards. This driver
implements the standard SD host controller APIs, and sets the host
property "is_spi" to indicate to the SD subsystem the card will be
running in SPI mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable new USDHC driver for all RT10xx boards, since those will have
the SDHC driver selected by Kconfig
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SDMMC driver to subsystem. SDMMC driver will handle initialization,
as well as SDMMC I/O. SD mode support is currently supported, SPI mode
support is not.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
All SD cards require SD CMD0 (reset) and CMD8 (send IF cond) at boot.
Add this portion of the initialization flow to SD subsystem, as well as
query command to check if card is SDIO.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SD subsystem headers. SD subsystem contains generic header for SD
initialization, and headers for SDIO and SDMMC cards.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
SD host controller driver runs basic SD host controller tests, including
checking SD presence, and sending commands to SD card. No data transfer
is performed.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add generic SDHC dts binding, as well as DTS binding for NXP USDHC.
Update iMX.RT DTS binding to use USDHC compatible
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Implement SDHC driver for NXP USDHC peripheral, supporting all api calls
available in the sdhc driver. This implementation leverages NXP's HAL,
and simply implements a shim layer over the HAL itself.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add api for SD host controller driver. SD host controller driver
supports the following operations:
- reset: reset host controller state
- request: send SD command and data via SDHC
- set_io: set I/O settings (voltage, clocks, etc..) on SDHC
- get_card_present: check for card presence
- execute_tuning: run tuning process for UHS cards
- card_busy: check if SD card bus is busy
- get_host_props: get host controller properties
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
LiteX CSRs can only be accessed on addresses aligned to 4 bytes.
That's why in 32-bit CSRs case there is bit shifting needed.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Removed register sizes from config struct, as they are known.
This allowed to remove driver specific function reading from CSR and use
`litex_write*` functions from LiteX HAL.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Use LiteX HAL functions instead of `sys_read*` or `sys_write*`
functions.
They use them inside, but choose which one to use according to
configured CSR data width.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
With universal LiteX HAL working, there is no need to perform multibyte
reads and writes using bitwise operations.
Just use appropriate `litex_read*` or `litex_write*` function.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Use LiteX HAL functions instead of `sys_read*` or `sys_write*`
functions.
They use them inside, but choose which one to use according to
configured CSR data width.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Use LiteX HAL functions instead of `sys_read*` or `sys_write*`
functions.
They use them inside, but choose which one to use according to
configured CSR data width.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Changes signature so it takes uint32_t instead of pointer to a
register.
Later `sys_read*` and `sys_write*` functions are used, which cast
given address to volatile pointer anyway.
This required changing types of some fields in LiteX GPIO driver and
removal of two casts in clock control driver.
There was a weird assert from LiteX GPIO driver, which checked whether
size of first register in dts was a multiple of 4.
It didn't make much sense, so I removed it.
Previous dts was describing size of a register in terms of subregisters
used. New one uses size of register, so right now it is almost always
4 bytes.
Most drivers don't read register size from dts anyway, so only changes
had to be made in GPIO and clock control drivers.
Both use `litex_read` and `litex_write` to operate on `n`bytes.
Now GPIO driver calculates this `n` value in compile time from given
number of pins and stores it in `reg_size` field of config struct like
before.
Registe sizes in clock control driver are hardcoded, because they are
tied to LiteX wrapper anyway.
This makes it possible to have code, independent of CSR data width.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Adds LITEX_CSR_DATA_WIDTH option to Kconfig
Depending on its value appropriate read/write handling is used
for accessing CSR registers.
By using `>=` in preprocessor conditions it is somewhat future-proofed.
Doesn't touch `litex_read` and `litex_write` yet.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Fixed the issue when sometimes "update" is not called for the
last RXRDY signal. First, need to reset the signal and only
after that need to call the "update" function.
Signed-off-by: Yuriy Vynnychek <yura.vynnychek@telink-semi.com>
Make the LSE driving capability configurable for the STM32 series.
Fixes#44737.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Currently the driver only setup the ADC to read from the
internal temperature channel on init. However, it is possible
that some other application that uses the ADC can setup the
ADC to read from some other channel and therefore subsequent
stm32_temp_sample_fetch will fail to read the targeted channel.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The ADC should be calibrated on init, there is no requirement
to calibrate ADC again on stm32_temp_init, remove it.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Keys' order - bn, n - might differ from the default due to
Length-First Map Key Ordering rules.
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
Regenerates the encoder and decoder. Treats integers and floating-point
values as separate entities instead of saying that those are numerical
values. Brings some memory savings.
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
Makes possible to write an empty CBOR array if there are no SenML CBOR
records that needs to be written. This came up when trying to delete a
portfolio object instance.
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
With LwM2M v1.1 SenML CBOR is preferred over SenML JSON.
TLV is on by default only with v1.0.
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
The peripheral is configured to update the connection
parameters for 5 seconds by default.
There is an abnormal situation with a very low probability.
The central actively disconnects or abnormally disconnects the
Bluetooth connection at the same time.
At this time, the connection disconnection event will be
handled by BT RX.
At this time, sysworkq has sent a parameter update request and
will receive a reply with status = 0x02, because the handle is
invalid at this time.
We can not just cancel work, because work->flag may be
in K_WORK_RUNNING, so work->flag is set to K_WORK_CANCELING
and subsequent conn_cleanup will unable call k_work_rescheduler
successfully.
According submit_to_queue_locked will return ret = -EBUSY.
if (flag_test(&work->flags, K_WORK_CANCELING_BIT)) {
/* Disallowed */
ret = -EBUSY;
As a result, the connection cannot be cleanup correctly.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
The NAPOT mode isn't computed properly in qemu when the full address
range is covered. Let's hardcode the value that the qemu code checks
explicitly until the appropriate fix is applied to qemu itself.
For reference, here's the qemu patch:
https://lists.gnu.org/archive/html/qemu-devel/2022-04/msg00961.html
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
QEMU does its dynamic instruction translation in 4096-byte-sized chunks.
Therefore it doesn't vet PMP access for each instruction prefetch but
for the whole "page" at once. If the end of the ROM area lands in the
middle of such a page with a corresponding PMP entry then any instruction
access within that page will fault even if it is located in the PMP
mapped portion.
To work around this QEMU peculiarity, we simply align the end of the ROM
area to a page boundary.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
