Value changed from 100us to 150us. Value was not enough upon softreset.
This value was arbitrarily chosen and should be changed if more
information on the subject is provided.
Fixes#43794
Signed-off-by: Diogo Correia <dcorreia@protonmail.com>
bmi160.c module defines DT_DRV_COMPAT, but bmi160_trigger.c doesn't.
This causes a catastrophic chain of events.
The bmi160.c module includes bmi160.h,
in which the macro DT_ANY_INST_ON_BUS_STATUS_OKAY
affects the size of bmi160_bus union.
So bmi160.c defines a bmi160_cfg struct which contains that union.
Now, in bmi160_trigger_init we get a pointer to that config struct.
The fact that this module now includes bmi160.h without
DT_DRV_COMPAT, causes it to think the union is empty.
That doesn't cause compilation error, just undefined behaviour,
In which you address an empty struct fields.
In general, I suggest that someone makes sure it doesn't happen
in other drivers as well. The problem presented here is general,
meaning that if an h file assumes someone defined DT_DRV_COMPAT
before and it doesn't,
it may lead to some weird behaviour, like the one described.
Signed-off-by: Avi Green <avigreen1978@yandex.com>
Replace all get_dev_data()/get_dev_config() accessor utilities with
dev->data and dev->config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The warning below appears once -Waddress-of-packed-mem is enabled:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_gyr_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:795:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
795 | data->sample.gyr, val);
| ~~~~~~~~~~~~^~~~
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_acc_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:807:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
807 | data->sample.acc, val);
| ~~~~~~~~~~~~^~~~
To avoid the warning, make the struct non-packed, since it is not
necessary in this case given that a union already guarantees that the
pointer to the union points to each member of the union equally..
More info in #16587.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some GPIO related functions were not being checked for errors.
This patch fixes coverity issue 236653.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In drivers/sensor/CMakeLists.txt, we have various lines like this:
add_subdirectory_ifdef(CONFIG_FOO foo)
Then drivers/sensor/foo/CMakeLists.txt says:
zephyr_library()
zephyr_library_sources_ifdef(CONFIG_FOO foo.c)
This is redundant; the foo/CMakeLists.txt won't be added to the build
system unless CONFIG_FOO=y in the first place, so there's no need for
extra boilerplate testing it again.
Remove all these unnecessary instances in each sensor driver's
CMakeLists.txt using this pattern:
zephyr_library()
zephyr_library_sources(foo.c)
In a couple of places, the '.c' extension is missing. Add them in for
consistency when that happens.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Fix#32774
Bit position BIT(7) is 1000 0000 in binary which is actually the
bit positon 128. BIT(7) can be used as a mask, but we need to define
the position specifically as the integer 7.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
Currently there is no way to distinguish between a caller
explicitly asking for a semaphore with a limit that
happens to be `UINT_MAX` and a semaphore that just
has a limit "as large as possible".
Add `K_SEM_MAX_LIMIT`, currently defined to `UINT_MAX`, and akin
to `K_FOREVER` versus just passing some very large wait time.
In addition, the `k_sem_*` APIs were type-confused, where
the internal data structure was `uint32_t`, but the APIs took
and returned `unsigned int`. This changes the underlying data
structure to also use `unsigned int`, as changing the APIs
would be a (potentially) breaking change.
These changes are backwards-compatible, but it is strongly suggested
to take a quick scan for `k_sem_init` and `K_SEM_DEFINE` calls with
`UINT_MAX` (or `UINT32_MAX`) and replace them with `K_SEM_MAX_LIMIT`
where appropriate.
Signed-off-by: James Harris <james.harris@intel.com>
When testing the bmi160 I've come across an issue where the readings
didn't make sense to me. The issue comes from reading the
BMI160_SAMPLE_BURST_READ_ADDR which is 0x0C assuming both accelerometer
and gyroscope. At this point we would normally read 12 bytes
(2 bytes per sample * 3 axes * 2 sensors). This reading takes place in
bmi160_sample_fetch and begins writing to data->sample.raw
Without this change, the first byte written is actually to the dummy
byte which effectively gets tossed. The issue is that this is the
GYR_X<7:0>(LSB) according to the BMI160 data sheet. When we later call
either bmi160_gyr_channel_get or bmi160_acc_channel_get we're looking
at sample.gyr and sample.acc (which is effectively shiften by 1 byte).
This change gets rid of the dummy byte which re-alignes gyr with the
start of the raw buffer.
Signed-off-by: Yuval Peress <peress@chromium.org>
At present this driver only supports SPI. Refactor it so that SPI is
just one of the options. This does not change any functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
This member holds the SPI bus pointer. Change its name to make that
more obvious and so that it can be used for an I2C bus also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are three separate read functions and two write
functions. This makes it harder to provide an interface that can work
with either SPI or I2C.
Use bmi160_read() for all reads and create a new bmi160_write()
function for all writes.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this driver only supports a single instance. It sets up some
of its config in the init routine. It is better to put config in
constant data so that multiple instances can be supported and RAM space
is minimised.
Update the driver accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently a 'bmi160' pointer is used to point to the driver data. This
confusing, as the driver uses both data and config. Rename the variable
to 'data' like the bme280 driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver uses verbose names for the config and data structures, which
makes it harder to see which one we are talking about. Shorten it, like
the bme280 driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This emulator supports enable functionality to start up the device and
read a few samples. It connects itself to any BMI160 device it finds in
the device tree. The SPI emulation controller driver is used to direct
SPI messages from the BMI160 driver to the BMI160 emulator.
Add a few more definitions to the header file, as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present register access is a mix of constants and open-coded values
in the driver. Add a few more constants to clean this up.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is necessary to wrap the device pointer into data.
Which was done already on most of them when global trigger is enabled.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use the named representation for no-wait to future-proof against a
change to the representation of timeout values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sensor.h to drivers/sensor.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
