Update the driver to account for variations in the SDK driver
when it uses the instance number instead of the base address.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
LPFlexcomm is a MFD device hence select this Kconfig whenever
it is enabled.
Remove the selection from the individual driver Kconfig files.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
When sending commands containing something like "AT+CFUN" the expected
regex was not escaped and as a result such regex never matched what has
been echoed over serial.
Escape all commands with re.escape() so that echoed shell commands are
always matched, even when they contain special characters (like '+' in the
example above).
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
On some boards, there is not dedicated reset pin for GT911, it might
be the same pin with display IC, or might be tighted to a high level
voltage.
This patch makes the rst_gpio can be empty.
Signed-off-by: Jason Yu <zejiang.yu@nxp.com>
This commit enables PMP on the default revision of the SiFive HiFive1
board. PMP was already enabled on the Rev B of this board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit sets `CONFIG_NEWLIB_LIBC_MIN_REQUIRED_HEAP_SIZE=2048` for the
SiFive HiFive1 board. Otherwise, the test fails on the following assert
from Newlib:
memory space available for newlib heap is less than the minimum required
size specified by CONFIG_NEWLIB_LIBC_MIN_REQUIRED_HEAP_SIZE
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit sets `CONFIG_NEWLIB_LIBC_MIN_REQUIRED_HEAP_SIZE=2048` for the
SiFive HiFive1 board. Otherwise, the test fails on the following assert
from Newlib:
memory space available for newlib heap is less than the minimum required
size specified by CONFIG_NEWLIB_LIBC_MIN_REQUIRED_HEAP_SIZE
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Set CONFIG_BT_MAX_PAIRED with same value as in host.
This is needed for CSIP tests with three lower testers:
CSIP/CL/SP/BV-07-C, CSIP/CL/SP/BV-03-C, CSIP/CL/SP/BV-04-C,
CSIP/CL/SPE/BI-01-C
Signed-off-by: Piotr Narajowski <piotr.narajowski@codecoup.pl>
Add pinctrl for SAI1 node. This means:
1) Adding definitions for the pads used by SAI1.
2) Creating a pin group and referencing it in
the SAI1 node via the `pinctrl-0` property.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add pinctrl for SAI1 node. This means:
1) Adding definitions for the pads used by SAI1.
2) Creating a pin group and referencing it in the
SAI1 node via the `pinctrl-0` property.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add support for performing pinctrl operations. For now,
the only supported operation is applying the pinctrl default
state. Pinctrl is left optional to allow for scenarios in which
this is not required (e.g: AMP system in which another
OS configures the pinctrl).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add a property to select the push-pull GPIO output type to drive the
I2C recovery. The default is open-drain.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
On the RT1170-EVKB, the framebuffer displays incorrectly
(shifted by about 1/4 of the screen width). This is because
pixelclk-active was set to 1 (which corresponds to
kELCDIF_DriveDataOnRisingClkEdge).
According to the RM68200 datasheet, the DSI transfert begins at
the uprising pixel clock and stop at the falling pixel clock. So,
pixelclk-active needs to be set to 0 (which corresponds to
kELCDIF_DriveDataOnFallingClkEdge).
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
On the RT1170-EVKB, the framebuffer displays incorrectly
(shifted by about 1/4 of the screen width). This is because
pixelclk-active was set to 1 (which corresponds to
kELCDIF_DriveDataOnRisingClkEdge).
According to the HX8394 datasheet, the DSI transfert begins at
the uprising pixel clock and stop at the falling pixel clock. So,
pixelclk-active needs to be set to 0 (which corresponds to
kELCDIF_DriveDataOnFallingClkEdge).
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Enable clock control for i.MX8ULP. This consists of:
1) Adding a PCC node in the DTS
2) Adding a header file containing the definitions
of the clocks used by the peripherals to be enabled.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This patch add supports for performing clock-related operations
on i.MX8ULP. This consists of:
1) Adding a LUT.
2) Adding an initialization function meant to tell the
HAL which rate the XTALs on the boards (EVK and EVK9)
run at. This is used by the functions that compute the
rate of an IP clock.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
In the case of some SOCs simply using the PCC base and clock
offset to build the clock ID passed to the HAL is not sufficient
since the clock ID may also contain some flags (e.g: see the case of
i.MX8ULP). For such SOCs, we change the semantic of the value passed
from the DTS (which is simply called "name", thus allowing us to
interpret it differently from SOC to SOC) to an index in a LUT
used to fetch the clock ID that can be safely passed to the HAL.
For compatibility reasons, we also keep the old way and use it
for SOCs which don't define such a LUT. The driver will decide
which method to use based on the LUT size (i.e: if 0, use the
old way, if != 0 use the new way).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Adds the device trees, Kconfig, and documentation files.
The following features have been confirmed working on hardware:
* LED
* Button
* ST7735 TFT-LCD
* External QuadSPI NOR Flash memory
* External SPI NOR Flash memory
* USB CDC ACM
* microSD card
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
- Remove OS specific instructions, instructions depend on the shell and
are the same across OS;
- Add fish shell to the documentation.
Signed-off-by: Théo Battrel <theo.util@protonmail.ch>
Change, for audio DSP and M7 cores, SOC_<name> to match
the exact soc name.
Update the board files accordingly.
These configs are used in SOF and NXP_HAL, so change
sha for these modules.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Enable sleep mode on LPC55S69 (corresponding to zephyr's runtime idle
mode). Add DT description and power api implementations.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The thermometer sensor sample application can support any board that
defines the `ambient-temp0` devicetree alias, but the restrictive
`platform_allow` list prevented twister from running on all but two
selected boards. Use a more flexible `dt_alias_exists` filter instead to
allow running this sample on additional boards.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Adds a devicetree alias to the ambient temperature sensor on
adi_eval_adin1110ebz to support the thermometer sensor sample
application.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Timing function need Cycle Count Register CYCCNT of DWT,
but Arm-Cortex-M23 only support DWT_CTRL, DWT_PCSR and DWT_COMP
& DWT_FUNCTION registers. It can't meet the requirement of timing
function, so to remove CPU_CORTEX_M_HAS_DWT.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Run clang-format on qdec_stm32.c.
This moves '\' in macros to line index 100, which ensures '\' still
aligns if a macro is edited with a new line that is longer than the
previous longest line.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The VLAN sample application only had configuration support for
the Ethernet interface and one VLAN interface, and left the one
VLAN interface unconfigured. Fix this by adding config support for
all three network interfaces created by the sample.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
