HAL API changes in ethernet and pwm
SoC RT595 power management code change
west.yml update
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
This prevents configuration errors if a board is configured when
the SoC indicates segger RTT support but the segger module is
not available.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This commit adds a missing `__weak` symbol to the `pm_policy_next_state`
function.
This is needed for e.g. `tests/kernel/profiling/profiling_api` to build
correctly.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The nRF9161 is technically a SiP (System-in-Package) that consists of
the nRF9120 SoC and additional components like PMIC, FEM, and XTAL,
so for nrfx/MDK the nRF9120 SoC is to be selected as the build target,
but since the nRF9161 is what a user can actually see on a board, using
only nRF9120 in the Zephyr build infrastructure might be confusing.
That's why in the top level of SoC definitions (for user-configurable
options in Kconfig, for example) the nRF9161 term is used and nRF9120
underneath.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use one common `if SOC_SERIES_NRF52X` instead of `depends on` for
each particular SoC option.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit 4be102f8e05a9fa12290d8209a8cb38569265478.
Inclusion of `<system_nrf*.>` from `soc.c` files is no longer needed
since `SystemInit()` is not called from those files.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds USB-HS support for LPC55S16, much in the same way that
LPC55S28 support was added previously.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Many areas of Zephyr divide and round up without using the DIV_ROUND_UP
macro. Make use of it, so that we make use of a tested system macro and
at the same time we make code more readable.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The init infrastructure, found in `init.h`, is currently used by:
- `SYS_INIT`: to call functions before `main`
- `DEVICE_*`: to initialize devices
They are all sorted according to an initialization level + a priority.
`SYS_INIT` calls are really orthogonal to devices, however, the required
function signature requires a `const struct device *dev` as a first
argument. The only reason for that is because the same init machinery is
used by devices, so we have something like:
```c
struct init_entry {
int (*init)(const struct device *dev);
/* only set by DEVICE_*, otherwise NULL */
const struct device *dev;
}
```
As a result, we end up with such weird/ugly pattern:
```c
static int my_init(const struct device *dev)
{
/* always NULL! add ARG_UNUSED to avoid compiler warning */
ARG_UNUSED(dev);
...
}
```
This is really a result of poor internals isolation. This patch proposes
a to make init entries more flexible so that they can accept sytem
initialization calls like this:
```c
static int my_init(void)
{
...
}
```
This is achieved using a union:
```c
union init_function {
/* for SYS_INIT, used when init_entry.dev == NULL */
int (*sys)(void);
/* for DEVICE*, used when init_entry.dev != NULL */
int (*dev)(const struct device *dev);
};
struct init_entry {
/* stores init function (either for SYS_INIT or DEVICE*)
union init_function init_fn;
/* stores device pointer for DEVICE*, NULL for SYS_INIT. Allows
* to know which union entry to call.
*/
const struct device *dev;
}
```
This solution **does not increase ROM usage**, and allows to offer clean
public APIs for both SYS_INIT and DEVICE*. Note that however, init
machinery keeps a coupling with devices.
**NOTE**: This is a breaking change! All `SYS_INIT` functions will need
to be converted to the new signature. See the script offered in the
following commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
init: convert SYS_INIT functions to the new signature
Conversion scripted using scripts/utils/migrate_sys_init.py.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
manifest: update projects for SYS_INIT changes
Update modules with updated SYS_INIT calls:
- hal_ti
- lvgl
- sof
- TraceRecorderSource
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: devicetree: devices: adjust test
Adjust test according to the recently introduced SYS_INIT
infrastructure.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: kernel: threads: adjust SYS_INIT call
Adjust to the new signature: int (*init_fn)(void);
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Remove per soc definitions that are already defined in the exact same
way in include/zephyr/arch/arm/aarch32/nmi.h.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Remove per soc definitions that are already defined in the exact same
way in include/zephyr/arch/arm/aarch32/nmi.h.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Initialization part of this anomaly is now handled internally
by the startup code provided by the MDK.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Zephyr PM expects the SoC layer upon wake to unmask interrupts
the PM layer masked. MEC172x was re-enabling interrupt globally
in the Cortex-M4 but not clearing the mask set by Zephyr PM.
This worked in previous Zephyr releases but broke in the latest
Zephyr changes. Fixed the SoC to re-enable interrupts globally
and call irq_unlock(0) as Zephyr PM does if pm_state_exit_post_ops
is not implemented. Tested on MEC172x EVB with PLL clock out pin
enabled and verified PLL goes off in deep sleep, system wakes,
and interrupts are firing.
Signed-off-by: scott worley <scott.worley@microchip.com>
This commit introduces power management support for EFR32BG SoCs.
Tested on the efr32bg_sltb010a board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
There are some issues with the current version of the code, mainly the
improper use of the internal OSC8M as a source for the DFLL48m without
division. The DFLL48M is designed to accept a maximum of ~33KHz
at it's input, as higher values will bring the multiplier down,
leading to instability.
Also added the following features:
* Support for external HF oscillator (XOSC)
* Support for crystal/external oscillators on XOSC32K/XOSC
* Automatic dividers/multiplier computation based on DT cpu frequency
* Support for user configurable NVM wait states
* Added option to skip clock (re)initialization (bootloader usecase).
Tests were performed on a custom SAMD20G18 board using different clock
sources and cpu frequencies.
Clocks were routed to GPIO pins and observed on a scope.
According to the datasheet, architecture is identical on D21/R21.
Due to the nature of the internal architecture and the fact that
DFLL48M is not really meant to output anything other than 48MHZ
some combinations of requested DT cpu frequency and source
frequency will not result in a perfect match.
Mostly insipred by the SAML21 implementation.
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
1. Move the GPIO mux setting to the soc layer. The GPIO MUX
value may vary based on the SoC Family
2. Enable the digital input buffer if available
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add configuration items to select various ARM debug options
such as SWD only, SWD plus SWV, or SWD plus ETM. The default
is SWD only.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Enable at SoC boot time when enabled through Kconfig. Cache management
API is not used since it could be built without its support enabled.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
When CONFIG_NOCACHE_MEMORY=y, the .nocache section is placed in between
__rodata_region_end and _app_smem_start/__kernel_ram_start. Make sure
this region is covered by the MPU background region so that the static
region for nocache is configured correctly.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Introduce the new stm32h5 soc serie from STMIcroelectronics.
Note that stm32h503x do not have TrustZone nor SAU
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove the manually created linker section, because it's already
automatically generated for all sram regions in the DTS with the
"zephyr,memory-region" compatibility.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Change device tree VW routing to a form allowing overrides.
Add two new DT optional properties for specifying the reset
source and reset value of each virtual wire. Only virtual
wires that are enabled using the status property are modified.
NOTE: eSPI virtual wires are controlled in groups of 4 by
hardware. The optional reset signal source properties applies
to all four virtual wires in the group. If this field is
changed from the hardware default, it should be changed for
only one virtual wire in the group. If the property exists
in more than one wire in the group it must be set to the
same value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Modify Mircrochip MEC172x eSPI driver to get eSPI virtual wire
hardware routing from device tree.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The clock control driver requires three pieces of information:
PCR register index, bit position, and clock domain. Clock domain
was missing from DT information and MCHP macros.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Some pico-sdk drivers call a panic function, originally implemented
as part of the Pico's C runtime. This commit adds a Zephyr compatible
implementation of panic, so that those drivers could be compiled with
Zephyr.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Product URL: https://www.ti.com/product/CC1352P7
Datasheet : https://www.ti.com/lit/ds/symlink/cc1352p7.pdf
Features:
Powerful 48-MHz Arm® Cortex®-M4F processor
* 704KB flash program memory
* 256KB of ROM for protocols and library functions
* 8KB of cache SRAM
* 144KB of ultra-low leakage SRAM with parity for
high-reliability operation
* Dual-band Sub-1 GHz and 2.4 GHz operation
Updates:
* Remove CC1352P7_LaunchXL due to compliance checks
* Add CC1352P7 updates
* Update hal_ti for CC1352P7 support
* Remove blank line at end of modules/Kconfig.simplelink
* Split struct and typedef for pinctrl_soc_pin/pinctrl_soc_pin_t
* Reference cc13x2_cc26x2/pinctrl_soc.h
* Reference cc13x2_cc26x2/soc.h
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
In general, RTC and TIMER driver implements counter API but there
are exception when those peripherals are used in a custom way
(e.g. for system timer or bluetooth). In that case, system must
prevent using counter based on a reserved instance. Previously,
it was managed by Kconfig options but that cannot be maintained
when switching to devicetree configuration of the counter driver.
A new approach removes Kconfig options and instead adds static
asserts in the files which are using direct peripherals. Those
asserts check if given node is not enabled in the device tree.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Removed the EEPROM and ESPI configuration from file
Kconfig.defconfig.mec172xnsz. Since it overrides the
setting present in the Device Tree file.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Use Device Tree bindings to configure clock source/frequency for enabled
UARTs only.
Get rid of UART clock ungating from `soc.c`, as that functionality has
been moved to the clock controller.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
Add functionality for changing the code location
based on the flash chosen node for RT devices.
Remove obsolete Kconfigs that used to be used
to set the code location for RT devices.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Allow selecting between direct SMPS and LDO on the startup. This
enables selecting to use SMPS regulators which can save bit of power.
Signed-off-by: Miika Karanki <miika.karanki@vaisala.com>
The STM32H730 series has a variant built with SMPS. It uses
`stm32h730xxq.h` header file instead of `stm32h730xx.h`, which has the
SMPS macro defined.
This commit adds the `SOC_STM32H730XXQ` configuration option to allow
the build system include the proper header file. With this change,
boards can enable `CONFIG_POWER_SUPPLY_DIRECT_SMPS` to set up the power
supply for the CPU.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Add clock initialization for MIPI and LCIDF to NXP RT5xx SOC.
Note that clock divider properties are used by both initialization
routines, as the required clock divider will vary depending on
attached display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
