One of the test case is performing long transfers using 1k buffers.
For some targets there may be not enough RAM to perform such
transfers. Make long buffer length configurable.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Fix the test for sending frames with the CAN_FRAME_ESI flag set. Sending
frames with this flag set in software is never allowed.
Fixes: 8023a58c2a
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Linter pass makes CI happy and keeps code compliant
with the stylistic guidelines of the project
Signed-off-by: Rafael Laya <rafael_laya97@hotmail.com.com>
This updates the documentation of all the NXP boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Rework overlays and add sysbuild/vpr_launcher folder to allow standard
test configuration for nrf54h20dk cpuppr.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Rework existing nrf54h20dk overlays to allow adding of
nrf54h20dk//cpuppr target.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
In order to allow fiting test in targets with smaller memory make
large buffer configurable through Kconfig.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
It will increase test coverage for adc driver, no test uses
ADC_GAIN_2_3 setting yet.
Signed-off-by: Bartlomiej Buczek <bartlomiej.buczek@nordicsemi.no>
Tests are checking error codes returned from adc_read() and
adc_channel_setup() used with invalid configurations.
Signed-off-by: Bartlomiej Buczek <bartlomiej.buczek@nordicsemi.no>
The ILPS22QS is an ultra-compact piezoresistive absolute pressure sensor
which functions as a digital output barometer, supporting dual full-scale
up to user- selectable 4060 hPa. The device delivers ultra-low pressure
noise with very low power consumption and operates over an extended
temperature range from -40 °C to +105 °C.
(https://www.st.com/en/mems-and-sensors/ilps22qs.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Check error codes when sending invalid frames:
- too big data payload;
- wrong set of flags.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
There is negative test for too high data bitrate.
Add test that checks too low data bitrate.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
This commit does the following:
1. tests set_callback and user_data
2. fixes the api as well as the drivers by passing user_data
back to the set callback
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Add overlay for APARD32690 board and add a new test case to
test RTIO functionalities of SPI MAX32 driver.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
Enable flash driver test for MAX32690 boards.
Signed-off-by: Mert Vatansever <mert.vatansever@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Add test suite which uses GPIO loopback to produce a "very low" and
"very high" voltage at the positive input of the comparator using the
output of a GPIO. The negative input is set to a voltage between the
high and low output voltages of the GPIO using whichever internal
reference is available to the comparator.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
