GRTC peripheral is present on nRF54H20,
so the tests should be executed on this target as well.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add support for half-duplex (3-wire) SPI operation using the Raspberry
Pi Pico PIO. To allow control of the size of the driver, including
half-duplex support is optional, under the control of Kconfig options.
The original PIO source code is also included as a reference.
Corrected 3-wire tx/rx counts.
Enable half-duplex code based on DTS configuration
Replace runtime checks with static BUILD_ASSERT()
Remove too-fussy Kconfig options
Removed PIO source per review request
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Since `NONE` is a valid option for key management in `connect`
command, we should remove the part in help text which says:
"valid only for secure SSIDs".
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Redundant kLPSPI_MasterPcsContinuous transfer config flag
is eliminated since this is set earlier.
Signed-off-by: Dipak Shetty <dipak.shetty@zeiss.com>
When using sysbuild,
set the primary MCU index to be the app core
only when we are building the test app in the app core.
Otherwise, if the test app is build in the net core,
the test command line parameters won't be sent by default
to it, and tests will fail.
Luckily, these tests are only built in CI using sysbuild
when we target the 5340bsim app core, and in all but 2,
even if sysbuild was used, this setting was propagated
to the zephyr build if we had separate net and app core
images.
The issue was introduced during the transition to
hwmv2.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Submit USBFSOTG_EVT_XFER on halt clear to allow queued
transfers to execute as soon as endpoint STALL is cleared.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Add overlay for nrf52_bsim to the fixed_top test.
For bsim board RTC register address has to be translated.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
UBSan was showing the following error:
```
runtime error: left shift of 137 by 24 places cannot be represented in
type 'int'
```
Cast the value to `uint32_t` to make UBSan happy.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Adds missing overlay and conf for native_sim/native/64 and
native_posix/native/64 platforms.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The comment states the reason for this requirement is to detect
violations by a remote peer. The ATT version of this was removed in
ea04fd95f9. TLDR: It's neither possible
for, nor the job of the host to police the remote device.
We remove this requirement to be more flexible about the number of
priority levels in the system, and to avoid the temptation of using
priorities as a synchronization mechanism.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
The configuration file is mostly tested for the nRF53 series
where the controller configuration is usually from the
hci_ipc sample.
This means that the existing audio.conf before this commit
has not really been tested for audio, and were missing a few
configurations to make it work properly.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
LLD produces warnings about orphaned sections if there are no matching
rules in the linker script:
ld.lld: warning: <internal>:(.symtab) is being placed in '.symtab'
ld.lld: warning: <internal>:(.shstrtab) is being placed in '.shstrtab'
ld.lld: warning: <internal>:(.strtab) is being placed in '.strtab'
Handle these sections when building with LLD to prevent the warnings.
Signed-off-by: Patryk Duda <patrykd@google.com>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies of the base overlay were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During the hwmv1->v2 transition, overlays from a base
board were made to be shared with the variants.
So at that time all overlays for variants which were
just copies were removed.
After that in
https://github.com/zephyrproject-rtos/zephyr/pull/71149
this shared/merged overlay behaviour was reverted,
but not all tests were fixed.
This is one of those. Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The last parameter to getsockopt() should be a socklen_t *
not an int *.
Let's fix it to avoid a build warning which breaks this tests
in CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Make DSA dependent on ETH_DSA_SUPPORT which is selected by driver
kconfigs, rather than having a list of dependencies.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Convert all of the NXP SOCs with ENET to use the new
binding scheme, which is used by the new driver.
Convert any boards using this SOC to the new scheme as well,
and remove from the documentation the bit about the experimental
nature of the new driver and the overlay that shall no longer exist.
Some of the boards I do not have the hardware of, so apologies
if something breaks, as I have no way to know. All the boards
were made sure to at least build.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Deprecate ETH_MCUX, by:
- Marking it as DEPRECATED in Kconfig, obviously.
- Unmarking the new driver as experimental.
- Putting the new and old drivers in the same folder.
- Reworking the menu appearance of the driver selection.
Note that technically now it is possible to choose the wrong
driver than what is enabled in DT, this is intentional, but
the correct one will obviously be enabled by default.
- Convert all sample overlays to the new Kconfigs. This was
part of the motivation for the shared overlays, as it was
causing twister/CI logs to look ugly and misleading due
to Kconfig warnings.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
I have tested the DSA support with ETH_NXP_ENET driver and it
works, so marking it as supported by adding it to the dependency
list for the DSA feature.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The MAC address macros are ridiculous in this driver.
Rewrite to be simpler and use eth.h common function.
Also, clarify the mac address generation on the DT overlays.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Convert from multiple threads for each instance to use
one workqueue for all instances. The benefit is to save
memory and use a kernel function that already exists
for a use case like this.
Also introduce the ETH_NXP_ENET_RX_THREAD_PRIORITY kconfig,
which makes the thread priority of the workqueue configurable.
Finally, remove the code enabling the RxBufferInterrupt, since
the meaning of it isn't used currently in this driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add functionality for when NET_POWER_MANAGEMENT (ie PM_DEVICE)
is enabled. This function code originally comes from the
old eth_mcux driver which was only tested on kinetis family SOCs,
so that family kconfig is a dependency for this feature for now.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Some comments in this driver are just redundant - the code
spells out exactly what the comment says. And some comment
blocks are just unnecessary to have. Finally, remove the TODO
comment because this is flagged by static analysis and there
are already tracking issues for the zero copy enhancement.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The dependencies should be in a 'depends on' clause.
Also, 'depends on PTP_CLOCK' is redundant because this is
within 'if PTP_CLOCK' already.
Additionally, conditionally include the PTP header in the mac driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Added changes required for nxp_enet ethernet driver to work
with multiple PHYs and fixed few problems:
- The cfg_link API resets PHY before configuring link. It was moved
here so the ethernet driver does not have to reset it - not all
PHYs need reset before configuring link and moving the reset code
here makes possible to have the reset done in a PHY specific way
(for example to reset by toggling GPIO pin). It also avoids ethernet
driver touching PHY registers without locking.
- When reset GPIO is not defined, reset is performed by setting reset
bit in control register.
- The cfg_link API does not return error when autonegotiation fails.
This fixes situation when the link is down at system start - ethernet
driver then skipped setting link-change callback and link was never
to be detected again.
- Added reset of excessive bits 16-31 when reading register values.
As only 16 bits are read from PHY, but the API is supposed to read
into uint32_t, the remaining bits contained previous data after
a successful read.
- Fixed missing mutex unlock when querying link state and link was down.
- Added missing initializer to link state variables. This could result
in link state change detection while link was still down, because
the speed/duplex settings could be random and old and new state
could be wrongly detected as different.
- Not logging link speed/duplex status when link is not up.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Enabled nxp lpadc driver acquisition time feature, the overlay file
can express acquisition time in microseconds, nanosecond and ADC
ticks.
The purpose of updating these overlay files is not only for local
testing, but also to remind users that they can use this feature.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
