Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some devices do not need to perform any initialization, so allow the
init function to be NULL. In this case, the initialization code will
just mark the device as initialized, i.e. ready.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The below is the unit test result for the driver and kernel of
it82xx2_evb board.
GPIO/gpio_basic_api: PASS
I2C/i2c_api: PASS
Flash: PASS
UART/uart_basic_api: PASS
PWM/pwm_api: PASS
WDT/wdt_basic_api: PASS
KSCAN/kscan_api: PASS
kernel/sched/schedule_api: PASS
kernel/sched/preempt: PASS
kernel/timer/timer_api: PASS
kernel/sleep: PASS
ADC/adc_api: PASS.
ADC note: conversion time~=61.6us
sample time delay~=60us
wait voltage stable time~=202.8us
Set sampling time to 500us will pass for ADC test.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
1. Increase sram to 256KB.
A block sram of SCAR0~15 is 4KB.
A block sram of SCAR16~19 is 16KB.
A block sram of SCAR20~23 is 32KB.
2. Removed the register of RVILMCR which has no effect.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The alternate pins of UART2 have been remapped, and the remapped
alternate pins must be added to the pinctrl map.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add the pinctrl node that has been remapped in the chip of it82xx2.
And modify kscan's pinctrl for the it82xx2.
And swap I2C default pins.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Use the minimum supported cis_offset_min considering that
ACL radio event does not overlap with CIG event. Use the
calculated maximum of local and remote cis_offset_min in the
Response PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We have an entry for shell_root_cmds using zephyr_iterable_section so
remove duplicate handling of shell_root_cmds.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Convert following construction:
elif self.options.device_serial or self.options.device_serial_pty:
if self.options.device_serial:
...
else
...
to the construction:
elif self.options.device_serial:
...
else self.options.device_serial_pty:
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use flash_timeout and flash_with_test options not only for
serial console but also for device_serial_pty.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
compliance script runs pylink on size_calc.py and reports:
C0325:Unnecessary parens after '=' keyword (superfluous-parens)
Fix warning by remove unnecessary parens.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
On iMX.RT devices, the number of GPIO pins exceeds the maximum of
64 that the PINT interrupt controller can support. Therefore, two
interrupt lines are now shared between the GPIO modules.
This patch allows the user to set the interrupt source for a GPIO
peripheral. For most LPC devices, this will always be the PINT. For some
RT devices, the PINT cannot use pins on GPIO modules other than 0 and 1
as input, and thus the INTA and INTB sources should be used.
Since Zephyr does not support sharing these interrupt between all GPIO
controllers, the user must configure a subset of all GPIO controllers to
use the shared module interrupts. An example of how to do so is provided
for the RT595 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove PINT management code from the LPC GPIO driver, as this code is
now contained within the PINT interrupt controller driver, which exposes
an interface to install interrupt callbacks.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce PINT driver, for NXP pin interrupt and pattern match engine.
The driver currently supports only the pin interrupt feature of the
PINT.
Add DTS entires for the PINT on LPC and RT devices that support this
peripheral, and remove the interrupt defintions that are PINT specific
from the GPIO module on these devices.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
If the timer driver only implements sys_clock_cycle_get_32() (meaning
CONFIG_TIMER_HAS_64BIT_CYCLE_COUNTER=n) and the hardware clock is high
enough then the reported cycle count may wrap an uint32_t during the
test. This makes validating the total test duration pointless as it
cannot be measured. Just print a warning instead of failing the test
in that case.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The Arm assembler in binutils 2.40 contains a change [1] which affects
how multiple directives on the same line are parsed.
Previously, the following combination of directives parsed successfully:
.code 32 .balign 4
With binutils 2.40, the following error is now seen:
Error: junk at end of line, first unrecognised character is `.'
To fix, insert a semicolon after '.code 32', as there already is after
'.thumb'.
[1] https://sourceware.org/git/?p=binutils-gdb.git;a=commitdiff;h=a37854f9162fac592b669eda53f465fc190c9341
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
rtio is utilizing iterable sections so the explicit linker
code does not need to exist so we can remove it.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
NTC thermistor changes updated the sample app output,
correcting harness string to match sample app.
Signed-off-by: Al Semjonovs <asemjonovs@google.com>
When building the rtio_api tests with arm-clang we get the following
compiler warning:
rtio_api/src/test_rtio_api.c:436:58: warning: format specifies type
'unsigned long' but the argument has type 'uintptr_t'
(aka 'unsigned int') [-Wformat]
TC_PRINT("userdata is %p, value %lu\n", cqe->userdata, idx);
~~~ ^~~
%u
Use PRIuPTR to fix the issue.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Updates the release notes to document which absolute symbols
(generated via GEN_ABSOLUTE_SYM) have been removed.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
Removes unused absolute symbols that are defined via the
GEN_ABSOLUTE_SYM() macro in the kernel directory.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
This patch adds HDA to device tree for LNL platforms.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The OFLEN bit has to be set by the host driver for ACE2.x. The
ownership of the IP is now handled at the host driver level, no longer
the firmware.
Setting it at the firmware level is a no-op if the bit is already set
by the host driver, and will fail it isn't already set.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
This patch fixes i2svss field initialisation in Device Tree for LNL
platform. It fixes this bug: #482
Problem is observed only when using SSP_BLOB_VER_1_5 version.
Unfortunatelly this version is not tested in FW validation tests.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
